This DTC is stored when the telephone transceiver assembly detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.
The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the power switch is turned on (IG).
If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1570 | Red LED Error | Current for the manual (SOS) switch indicator (red) exceeds malfunction threshold for 10 seconds or more when the power switch is on (IG). | ·
Telephone transceiver assembly ·
Map light assembly (manual (SOS) switch) ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
If DTC B1570 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect 2 dry-cell batteries (1.5 V each) in series.
Connect a positive (+) lead from the batteries to terminal 8 (IND1) and a negative (-) lead to terminal 12 (GND3) of the map light assembly (manual (SOS) switch) connector.
Check if the manual (SOS) switch indicator (red) illuminates.
Manual (SOS) switch indicator (red) illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H6 telephone transceiver assembly assembly.
Disconnect the P14 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-11 (IND1) - P14-8 (IND1) | Always | Below 1 Ω |
| H6-11 (IND1) or P14-8 (IND1) - Body ground | Always | 10 kΩ or higher |
| H6-26 (SIG-) - P14-12 (GND3) | Always | Below 1 Ω |
| H6-26 (SIG-) or P14-12 (GND3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT