Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS TRANSCEIVER › 2019.02–2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0370494 TELEMATICS TRANSCEIVER A

TELEMATICS  TELEMATICS TRANSCEIVER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the telephone transceiver assembly removal/installation are shown below.

Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link
Telephone transceiver assembly
for ERA-GLONASS:

Register vehicle information


Emergency call service (Click here)
for eCall:
·

Register vehicle information

·

DCM activation


Emergency call service (Click here)
Mobilephone battery Reset mobilephone battery condition Emergency call service for ERA-GLONASS:
(Click here)
for eCall:
(Click here)

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 55900 2.REMOVE AIR CONDITIONING CONTROL ASSEMBLY

Hide 55434B 3.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Hide 4.REMOVE TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (for LHD)

a.

w/ Navigation System, for eCall:

i.
E406834C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the 3 connectors and detach the clamp.


iii.
E406835C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, and then while bending the instrument panel safety pad assembly, detach the guide and remove the telephone transceiver assembly with bracket.


iv.

Disconnect each connector.

HINT:

Remove the telephone transceiver assembly with bracket together with the No. 2 antenna cord sub-assembly and No. 2 navigation wire.




b.

w/ Navigation System, for ERA-GLONASS:

i.
E416838C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the 3 connectors and detach the clamp.


iii.
E416839C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, and then while bending the instrument panel safety pad assembly, detach the guide and remove the telephone transceiver assembly with bracket.


iv.

Disconnect each connector.

HINT:

Remove the telephone transceiver assembly with bracket together with the No. 2 antenna cord sub-assembly and No. 2 navigation wire.




c.

w/o Navigation System, for ERA-GLONASS:

i.
E416840C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the connector and detach the clamp.


iii.
E416841C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the telephone transceiver assembly with bracket.


iv.

Disconnect the connector.

HINT:

Remove the telephone transceiver assembly with bracket together with the No. 2 antenna cord sub-assembly.




d.

w/ Connector holder:

i.
E409944C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the 3 connectors and detach the clamp.


iii.
E409945C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the telephone transceiver assembly with bracket.


iv.

Disconnect the connector.

HINT:

Remove the telephone transceiver assembly with bracket together with the No. 2 antenna cord sub-assembly.




Hide 5.REMOVE TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (for RHD)

a.

w/ Navigation System:

i.
E406864C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the 3 connectors and detach the clamp.


iii.
E406865C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, and then while bending the instrument panel safety pad assembly, detach the guide and remove the telephone transceiver assembly with bracket.


iv.

Disconnect each connector.

HINT:

Remove the telephone transceiver assembly with bracket together with the No. 2 antenna cord sub-assembly and No. 2 navigation wire.




b.

w/o Navigation System:

i.
E406858C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the connector and detach the clamp.


iii.
E406859C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the telephone transceiver assembly with bracket.


iv.

Disconnect the connector.

HINT:

Remove the telephone transceiver assembly with bracket together with the No. 2 antenna cord sub-assembly.




c.

w/ Connector holder:

i.
E409946C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Remove the 2 bolts.


ii.

Disconnect the 3 connectors and detach the clamp.


iii.
E409947C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the telephone transceiver assembly with bracket.


iv.

Disconnect the connector.

HINT:

Remove the telephone transceiver assembly with bracket together with the No. 2 antenna cord sub-assembly.




Hide 86101J 6.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for LHD)

a.

w/ Navigation System, for eCall:

i.
E406836

Disconnect the 3 connectors.


ii.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



b.

w/ Navigation System, for ERA-GLONASS:

i.
E416842

Disconnect the 3 connectors.


ii.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



c.

w/o Navigation System, for ERA-GLONASS:

i.
E416843

Disconnect the 2 connectors.


ii.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



Hide 86101J 7.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

w/ Navigation System:

i.
E406854

Disconnect the 3 connectors.


ii.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



b.

w/o Navigation System:

i.
E406860

Disconnect the 2 connectors.


ii.

Detach the clamp and remove the No. 2 antenna cord sub-assembly.



Hide 86842J 8.REMOVE NO. 2 NAVIGATION WIRE (for LHD)

a.

w/ Navigation System, for eCall:

i.
E406837

Disconnect the connector.


ii.

Detach the clamp and remove the No. 2 navigation wire.



b.

w/ Navigation System, for ERA-GLONASS:

i.
E416844

Disconnect the connector.


ii.

Detach the clamp and remove the No. 2 navigation wire.



Hide 86842J 9.REMOVE NO. 2 NAVIGATION WIRE (for RHD)

a.
E406855

Disconnect the connector.


b.

Detach the clamp and remove the No. 2 navigation wire.


Hide 86842J 10.REMOVE NO. 2 NAVIGATION WIRE (w/ Connector Holder)

E409943

a.

Detach the clamp and remove the No. 2 navigation wire.


Hide 86457 11.REMOVE NO. 1 MULTI-MEDIA MODULE BRACKET

a.
E406838

w/ Navigation System:

Remove the 3 screws and No. 1 multi-media module bracket.


b.
E409950

w/o Navigation System:

Remove the screw and No. 1 multi-media module bracket.


Hide 86457A 12.REMOVE NO. 2 MULTI-MEDIA MODULE BRACKET

a.
E406839

w/ Navigation System:

Remove the 3 screws and No. 2 multi-media module bracket.


b.
E409951

w/o Navigation System:

Remove the screw and No. 2 multi-media module bracket.


Hide 86740 13.REMOVE TELEPHONE TRANSCEIVER ASSEMBLY