Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › 2019.02–2019.09
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0389152 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B15C4  SRS Communication Error  


DESCRIPTION

If the telephone transceiver assembly detects an error in communication between itself and the airbag sensor assembly as a result of a self check, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C4 SRS Communication Error The telephone transceiver assembly detects an error in signals from the airbag sensor assembly when power switch on (IG).
·

Telephone transceiver assembly

·

Airbag sensor assembly

·

Harness or connector

·

Airbag system



WIRING DIAGRAM

E342824E51
1.25,0.833 1.865,1.031 0.615,0.198 10 false GSW3 5.531,0.854 6.146,1.052 0.615,0.198 10 false GSW 1.75,0.729 2.063,0.927 0.313,0.198 10 false 23 5.26,0.729 5.573,0.927 0.313,0.198 10 false 24 0.927,1.406 1.323,1.604 0.396,0.198 10 false G70 5.281,1.396 5.677,1.594 0.396,0.198 10 false H6 0.917,1.583 2.938,1.875 2.021,0.292 10 false Airbag Sensor Assembly 5.271,1.594 6.656,2.469 1.385,0.875 10 false Telephone Transceiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION

·

This vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check if airbag system DTCs are output.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.INSPECT TELEPHONE TRANSCEIVER ASSEMBLY

B

2.INSPECT TELEPHONE TRANSCEIVER ASSEMBLY
a.
B240640C49
1.469,0.104 1.865,0.344 0.396,0.24 2.354,1.25 2.563,1.698 2.563,1.698 2.688,1.698 false 0.125,0.125 0.396,0.385 0.271,0.26 10 false *a 2.729,1.625 3.177,1.906 0.448,0.281 10 false GSW 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND 0.208,2.333 0.479,2.594 0.271,0.26 10 false *b 1.573,0.146 1.885,0.344 0.313,0.198 10 false H6
*a Component with harness connected
(Telephone Transceiver Assembly)
*b Waveform


Check the output waveform.

i.

Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


ii.

Connect an oscilloscope to terminal H6-24 (GSW) - Body ground.


iii.

Turn the power switch on (IG).


iv.

Check the signal waveform according to the condition(s) in the table below.

Reference Waveform:
Item Condition
Tester connection H6-24 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms/DIV.
Vehicle condition Power switch on (IG)


OK:

Waveform is as shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H6 telephone transceiver assembly connector.


b.

Disconnect the G70 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-24 (GSW) - G70-23 (GSW3) Always Below 1 Ω
H6-24 (GSW) or G70-23 (GSW3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR