Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › 2019.02–2019.09
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0389152 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B1AC0  Telephone Speaker Cable Connection Malfunction  


DESCRIPTION

If there is an open in a speaker circuit, the telephone transceiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the telephone transceiver assembly or front No. 4 speaker assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1AC0 Telephone Speaker Cable Connection Malfunction The malfunction is detected in the telephone speaker circuit for approximately 10 seconds or more.
·

Front No. 4 speaker assembly

·

Telephone transceiver assembly

·

Harness or connector



WIRING DIAGRAM

E405969E04
4.552,2.521 6.646,3.125 2.094,0.604 10 false Telephone Transceiver Assembly 1.125,2.479 3.146,2.74 2.021,0.26 10 false Front No. 4 Speaker Assembly 4.563,2.333 6.365,2.875 1.802,0.542 10 false H6 4.344,1.146 5.667,2.125 1.323,0.979 10 false 5 4.615,1.25 5.938,2.229 1.323,0.979 10 false SPO+ 1.75,1.25 3.073,2.229 1.323,0.979 10 false SP+ 1.813,1.688 3.135,2.667 1.323,0.979 10 false SP- 4.625,1.729 5.948,2.708 1.323,0.979 10 false SPO- 4.344,1.583 5.667,2.563 1.323,0.979 10 false 6 2.167,1.135 3.49,2.115 1.323,0.979 10 false 3 2.177,1.563 3.5,2.542 1.323,0.979 10 false 2 1.125,2.281 4.188,2.479 3.063,0.198 10 false G12

CAUTION / NOTICE / HINT

NOTICE:

When replacing the telephone transceiver assembly, make sure to replace it with a new one.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 10 seconds.


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (FRONT NO. 4 SPEAKER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (FRONT NO. 4 SPEAKER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the G12 front No. 4 speaker assembly connector.


b.

Disconnect the H6 telephone transceiver assembly connector.


c.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-3 (SP+) - H6-5 (SPO+) Always Below 1 Ω
G12-2 (SP-) - H6-6 (SPO-) Always Below 1 Ω
G12-3 (SP+) or H6-5 (SPO+) - Body ground Always 10 kΩ or higher
G12-2 (SP-) or H6-6 (SPO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT NO.4 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT NO.4 SPEAKER ASSEMBLY
a.

Remove the No. 4 front speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the No. 4 front speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT