Home › Engine / Hybrid System › A25B-FXS (ENGINE MECHANICAL) › ENGINE UNIT › from 2019.02
RM3620E _51 Engine / Hybrid System _080117 A25B-FXS ENGINE MECHANICAL _0390040 ENGINE UNIT G

A25B-FXS ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A400361

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.

Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

A293105C23
1.5,0.302 1.969,0.302 false 2.344,0.302 2.875,0.302 false 1.448,0.958 2.052,0.698 true 2.313,0.698 2.896,0.865 true 1.5,1.125 2.063,0.938 false 2.302,0.938 2.833,1.083 false 1.385,1.406 2.052,1.229 true 2.313,1.219 2.938,1.365 true 1.302,1.99 2.052,1.583 true 2.323,1.573 3.042,1.969 true 1.469,2.115 2.063,1.958 true 2.323,1.958 2.875,2.104 true 4.698,1.104 5.052,1.354 false 2.115,0.844 2.427,1 0.313,0.156 10 false *f 2.115,1.469 2.313,1.708 0.198,0.24 10 false *g 1.229,0.031 1.542,0.188 0.313,0.156 10 false *a 3.01,0.031 3.323,0.188 0.313,0.156 10 false *b 2.115,0.594 2.427,0.75 0.313,0.156 10 false *c 2.115,1.135 2.427,1.292 0.313,0.156 10 false *d 2.115,1.854 2.427,2.01 0.313,0.156 10 false *e 2.031,0.219 2.49,0.417 0.458,0.198 10 false SST 4.427,0.938 4.885,1.135 0.458,0.198 10 false SST
*a Correct *b Incorrect
*c Tapered Path *d Low Pressure Chamber
*e High Pressure Chamber *f Plunger
*g Check Ball - -


SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

The plunger is very difficult to move.


HINT:

If the plunger is easy to move, replace the valve lash adjuster assembly.



Hide 13511 3.INSPECT CAMSHAFT

a.
A400362

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

0.03 mm (0.00118 in.)


HINT:
·

If the runout is more than the maximum, replace the camshaft.

·

Check the camshaft oil clearance after replacing the camshaft.





b.
A400363

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:

42.217 to 42.417 mm (1.66208 to 1.66995 in.)


Minimum Cam Lobe Height:

42.157 mm (1.65972 in.)


HINT:

If the cam lobe height is less than the minimum, replace the camshaft.




c.
A400364

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 33.984 to 34.000 mm (1.33795 to 1.33858 in.)
Other journals 23.959 to 23.975 mm (0.94326 to 0.94389 in.)


HINT:

If the journal diameter is not as specified, check the camshaft oil clearance.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION




Hide 13512 4.INSPECT NO. 2 CAMSHAFT

a.
A400365

Inspect the No. 2 camshaft for runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

0.03 mm (0.00118 in.)


HINT:
·

If the runout is more than the maximum, replace the No. 2 camshaft.

·

Check the camshaft oil clearance after replacing the No. 2 camshaft.





b.
A400366

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
No. 2 camshaft 37.914 to 38.114 mm (1.49267 to 1.50054 in.)
No. 2 camshaft (for Fuel Pump) 39.398 to 39.598 mm (1.55109 to 1.55897 in.)


Minimum Cam Lobe Height:
Item Specified Condition
No. 2 camshaft 37.804 mm (1.48834 in.)
No. 2 camshaft (for Fuel Pump) 39.348 mm (1.54913 in.)


HINT:

If the cam lobe height is less than the minimum, replace the No. 2 camshaft.




c.
A400367

Inspect the No. 2 camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 40.984 to 41.000 mm (1.61354 to 1.61417 in.)
Other journals 23.959 to 23.975 mm (0.94326 to 0.94389 in.)


HINT:

If the journal diameter is not as specified, check the camshaft oil clearance.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION




Hide 13511 5.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps, No. 4 camshaft bearing cap, camshaft housing sub-assembly and camshaft journals.


b.

Place the camshaft and No. 2 camshaft on the camshaft housing sub-assembly.


c.
A400368C01
1.198,1.042 1.01,0.365 1.01,0.365 0.854,0.365 true 0.656,0.25 0.969,0.448 0.313,0.198 10 false *a
*a Plastigage


Lay a strip of Plastigage across each of the camshaft journals.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY

NOTICE:

Do not turn the camshafts.




f.
A400369C01
0.604,0.813 0.802,0.813 0.802,0.813 1.167,1.333 true 0.542,3.885 0.281,3.146 0.281,3.146 0.552,3.24 true 2.625,3.396 1.896,4.51 1.896,4.51 1.083,3.365 true 2.156,3.396 1.896,4.49 1.896,4.49 1.604,3.375 true 2.635,3.979 1.896,4.5 1.896,4.5 1.094,3.969 true 2.156,3.969 1.896,4.49 1.896,4.49 1.625,3.979 true 0.406,0.708 0.719,0.906 0.313,0.198 10 false *a 0.094,3.031 0.406,3.229 0.313,0.198 10 false *b 1.823,4.5 2.135,4.667 0.313,0.167 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journal


Measure the Plastigage at its widest point.

Standard Oil Clearance (for camshaft):
Item Specified Condition
No. 1 journal 0.035 to 0.072 mm (0.00138 to 0.00283 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Standard Oil Clearance (for No. 2 camshaft):
Item Specified Condition
No. 1 journal 0.027 to 0.064 mm (0.00106 to 0.00252 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance (for camshaft):
Item Specified Condition
No. 1 journal 0.085 mm (0.00335 in.)
Other journals 0.085 mm (0.00335 in.)


Maximum Oil Clearance (for No. 2 camshaft):
Item Specified Condition
No. 1 journal 0.085 mm (0.00335 in.)
Other journals 0.085 mm (0.00335 in.)


NOTICE:

Completely remove the Plastigage after the inspection.


HINT:

If the oil clearance is more than the maximum, replace the camshaft or No. 2 camshaft. If necessary, replace the camshaft housing sub-assembly.



Hide 13506 6.INSPECT CHAIN SUB-ASSEMBLY

a.
A382970C04
1.625,0.906 1.938,1.104 0.313,0.198 10 false *a
*a Measurement Length


Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

116.35 mm (4.58 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


HINT:

If the average elongation is more than the maximum, replace the chain sub-assembly.



Hide 13507A 7.INSPECT OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

a.
A382970C01
1.625,0.906 1.938,1.104 0.313,0.198 10 false *a
*a Measurement Length


Using a spring scale, pull the oil pump drive chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

116.35 mm (4.58 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


HINT:

If the average elongation is more than the maximum, replace the oil pump drive chain sub-assembly.



Hide 13519B 8.INSPECT OIL PUMP DRIVE SPROCKET

a.
A400370

Place the oil pump drive chain sub-assembly around the oil pump drive sprocket.


b.

Using a vernier caliper, measure the diameter of the oil pump drive sprocket and oil pump drive chain sub-assembly.

Minimum Gear Diameter (with Oil Pump Drive Chain Sub-assembly):

51.23 mm (2.02 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the oil pump drive chain sub-assembly and oil pump drive sprocket.



Hide 15163C 9.INSPECT OIL PUMP DRIVE SHAFT SPROCKET

a.
A402717

Place the oil pump drive chain sub-assembly around the oil pump drive shaft sprocket.


b.

Using a vernier caliper, measure the diameter of the oil pump drive shaft sprocket and oil pump drive chain sub-assembly.

Minimum Gear Diameter (with Oil Pump Drive Chain Sub-assembly):

51.23 mm (2.02 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the oil pump drive chain sub-assembly and oil pump drive shaft sprocket.



Hide 13050 10.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A402718

Place the chain sub-assembly around the camshaft timing gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing gear assembly and chain sub-assembly.

Minimum Gear Diameter (with Chain Sub-assembly):

100.01 mm (3.94 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing gear assembly.



Hide 13070A 11.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A402719

Place the chain sub-assembly around the camshaft timing exhaust gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing exhaust gear assembly and chain sub-assembly.

Minimum Gear Diameter (with Chain Sub-assembly):

100.01 mm (3.94 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing exhaust gear assembly.



Hide 13521 12.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A402721

Place the chain sub-assembly around the crankshaft timing sprocket.


b.

Using a vernier caliper, measure the diameter of the crankshaft timing sprocket and chain sub-assembly.

Minimum Sprocket Diameter (with Chain Sub-assembly):

51.23 mm (2.02 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.



Hide 13540 13.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A400371C01
2.781,1.896 2.604,1.896 2.604,1.896 2.604,1.458 false 2.865,1.802 3.177,2 0.313,0.198 10 false *a
*a Plunger


Push the plunger and check that it moves smoothly.

HINT:

If the plunger does not move smoothly, replace the No. 1 chain tensioner assembly.



Hide 13559 14.INSPECT CHAIN TENSIONER SLIPPER

a.
A400372C01
3.177,1.063 3.427,1.26 0.25,0.198 10 false *a
*a Depth


Using a vernier caliper, measure the wear depth of the chain tensioner slipper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner slipper.



Hide 13561 15.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A400373C01
2.938,1.021 3.25,1.219 0.313,0.198 10 false *a
*a Depth


Using a vernier caliper, measure the wear depth of the No. 1 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 1 chain vibration damper.



Hide 13620B 16.INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE

a.
A400374

Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.

Standard Thrust Clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum Thrust Clearance:

0.09 mm (0.00354 in.)


HINT:

If the thrust clearance is more than the maximum, replace the engine balancer assembly.



Hide 13620B 17.INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE

a.
A400375

Using a dial indicator, measure the thrust clearance while moving the No. 2 balance shaft back and forth.

Standard Thrust Clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum Thrust Clearance:

0.09 mm (0.00354 in.)


HINT:

If the thrust clearance is more than the maximum, replace the engine balancer assembly.



Hide 11101A 18.INSPECT CYLINDER HEAD SET BOLT

a.

for 140 mm cylinder head set bolt:

i.
A400376C01
2.219,0.344 2.531,0.542 0.313,0.198 10 false *a 1.292,1.51 1.604,1.708 0.313,0.198 10 false *b
*a Measurement Point
*b 105 mm (4.13 in.)


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard Diameter:

10.7 to 10.9 mm (0.421 to 0.429 in.)


Minimum Diameter:

10.6 mm (0.417 in.)


Measurement Point (Distance from the Seat):

105 mm (4.13 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.





b.

for 150 mm cylinder head set bolt:

i.
A400376C01
2.219,0.344 2.531,0.542 0.313,0.198 10 false *a 1.292,1.51 1.604,1.708 0.313,0.198 10 false *b
*a Measurement Point
*b 115 mm (4.53 in.)


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard Diameter:

11.7 to 11.9 mm (0.461 to 0.469 in.)


Minimum Diameter:

11.6 mm (0.457 in.)


Measurement Point (Distance from the Seat):

115 mm (4.53 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.





Hide 17141 19.INSPECT EXHAUST MANIFOLD

a.
A400377

Using a precision straightedge and feeler gauge, check the surface that contacts the cylinder head sub-assembly for warpage.

Maximum Warpage:

0.7 mm (0.0276 in.)


HINT:

If the warpage is more than the maximum, replace the exhaust manifold.



Hide 15703A 20.INSPECT OIL NOZZLE VALVE SUB-ASSEMBLY

a.
A404938C01
1.26,1.854 1.521,1.479 1.521,1.479 1.625,1.479 false 0.479,1.677 0.344,1.042 0.344,1.042 0.271,1.042 true 2.906,0.823 3.219,1.021 0.313,0.198 10 false *a 2.083,1.042 2.396,1.24 0.313,0.198 10 false *b 2.396,0.75 2.854,0.948 0.458,0.198 10 false 90° 1.896,0.167 2.208,0.365 0.313,0.198 10 false *d 1.656,1.385 1.969,1.583 0.313,0.198 10 false *d 0.083,0.927 0.396,1.125 0.313,0.198 10 false *c
*a 1.0 mm (0.0394 in.)
*b 5.0 mm (0.197 in.)
*c Check Valve
*d Wire
V100135

Move the wire in this direction.
V100136

Movement of Check Valve


Using a piece of wire, check that the check valve is not stuck.

HINT:
·

Form a 1.0 mm (0.0394 in.) diameter piece of wire to the shape shown in the illustration.

·

If the check valve is stuck, replace the oil nozzle valve sub-assembly with a new one.




b.
A404939C01
1.354,1.635 0.854,1.406 0.854,1.406 1.396,1.49 true 1.854,1.781 2.615,1.688 2.615,1.688 1.896,1.635 true 0.969,0.49 1.115,0.49 1.115,0.49 1.563,0.688 false 1.854,0.323 2.01,0.521 0.156,0.198 10 false A 0.688,1.302 0.844,1.5 0.156,0.198 10 false B 2.677,1.594 2.833,1.792 0.156,0.198 10 false B 0.792,0.406 1.104,0.604 0.313,0.198 10 false *a
*a Hose


Connect a hose to the oil nozzle valve sub-assembly.


c.

Check that air does not leak from the port (B) when blowing air into the port (A).

HINT:

If air leaks from the port (B), replace the oil nozzle valve sub-assembly with a new one.



d.
A404940C01
1.281,1.448 0.906,1.333 0.906,1.333 1.313,1.323 true 1.75,1.552 2.344,1.719 2.344,1.719 1.781,1.438 true 1.292,0.323 1.563,0.323 false 2.073,0.313 2.229,0.51 0.156,0.198 10 false A 0.771,1.26 0.927,1.458 0.156,0.198 10 false B 2.417,1.667 2.573,1.865 0.156,0.198 10 false B 1.115,0.229 1.427,0.427 0.313,0.198 10 false *a
*a Hose
V100135

Move the wire in this direction.
V100136

Movement of Check Valve


With the check valve depressed using a piece of wire, check that air flows from the port (B) when blowing air into the port (A).

HINT:

If air does not flow from the port (B), replace the oil nozzle valve sub-assembly with a new one.



e.

Disconnect the hose from the oil nozzle valve sub-assembly.