Home › Engine / Hybrid System › A25B-FXS (ENGINE MECHANICAL) › CYLINDER HEAD › 2019.02–2020.08
RM3620E _51 Engine / Hybrid System _080117 A25B-FXS ENGINE MECHANICAL _0390041 CYLINDER HEAD A

A25B-FXS ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)(for 2WD)
(Click here)(for 4WD/AWD)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment
1.

Clear the zero point calibration data and stored linear solenoid valve calibration data.

2.

Perform initialization and calibration of the linear solenoid valve.

3.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

NOTICE:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 13711 1.REMOVE INTAKE VALVE

a.
A400439N01
0.958,0.448 1.25,0.115 1.25,0.115 1.406,0.115 true 2.25,1.844 2.01,2.042 2.01,2.042 1.865,2.042 false 1.469,0.021 1.927,0.219 0.458,0.198 10 false SST 1.563,1.958 2.021,2.156 0.458,0.198 10 false SST

Using SST, compress each intake valve compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 intake valve compression springs and 8 intake valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13715 2.REMOVE EXHAUST VALVE

a.
A400441N01
1.375,1.875 1.583,1.99 1.583,1.99 1.75,1.99 false 1.781,0.135 1.99,0.135 1.99,0.135 2.313,0.26 true 1.823,1.927 2.281,2.125 0.458,0.198 10 false SST 1.406,0.063 1.75,0.281 0.344,0.219 10 true SST

Using SST, compress each exhaust valve compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 exhaust valve compression springs and 8 exhaust valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 3.REMOVE VALVE STEM OIL SEAL

a.
A400443

Using needle-nose pliers, remove the 16 valve stem oil seals.


Hide 13734A 4.REMOVE INTAKE VALVE SPRING SEAT

a.
A400444

Using compressed air and a Magnet Hand, remove the 8 intake valve spring seats from the cylinder head sub-assembly by blowing air onto them.


Hide 13734B 5.REMOVE EXHAUST VALVE SPRING SEAT

a.

Using compressed air and a Magnet Hand, remove the 8 exhaust valve spring seats from the cylinder head sub-assembly by blowing air onto them.


Hide 11117E 6.REMOVE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.


A400445

a.

Using a 6 mm hexagon socket wrench, remove the 4 No. 1 straight screw plugs from the cylinder head sub-assembly.


Hide 7.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A400447

Using an E8 "TORX" socket wrench, remove the 7 stud bolts.