If the power switch is on (IG), the hybrid vehicle control ECU assembly applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the +B1 and +B2 terminals.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the power switch on (IG).
for LHD:
Measure the voltage according to the value(s) in the table below.
| *A | for LHD | - | - |
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-11 (+B1) - Body ground | Power switch on (IG) | 11 to 14 V |
| A30-1 (+B2) - Body ground | Power switch on (IG) | 11 to 14 V |
for RHD:
Measure the voltage according to the value(s) in the table below.
| *A | for RHD | - | - |
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-11 (+B1) - Body ground | Power switch on (IG) | 11 to 14 V |
| G63-1 (+B2) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A30*1, G63*2 and A31*1, G64*2 hybrid vehicle control ECU assembly connectors.
*1: for LHD
*2: for RHD
for LHD:
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | - | - |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-3 (E1) - Body ground | Always | Below 1 Ω |
| A31-12 (E01) - Body ground | Always | Below 1 Ω |
| A31-11 (E02) - Body ground | Always | Below 1 Ω |
| A31-34 (E12) - Body ground | Always | Below 1 Ω |
for RHD:
Measure the resistance according to the value(s) in the table below.
| *A | for RHD | - | - |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G63-3 (E1) - Body ground | Always | Below 1 Ω |
| G64-12 (E01) - Body ground | Always | Below 1 Ω |
| G64-11 (E02) - Body ground | Always | Below 1 Ω |
| G64-34 (E12) - Body ground | Always | Below 1 Ω |
Reconnect the A30*1, G63*2 and A31*1, G64*2 hybrid vehicle control ECU assembly connectors.
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-5 (MREL) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 3 Relay Block and Junction Block Assembly |
| *2 | IGCT NO. 2 Fuse |
Remove the IGCT NO. 2 fuse from the No. 3 relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IGCT NO. 2 fuse terminals | Always | Below 1 Ω |
Install the IGCT NO. 2 fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 3 Relay Block and Junction Block Assembly |
| *2 | IGCT Fuse |
Remove the IGCT fuse from the No. 3 relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IGCT fuse terminals | Always | Below 1 Ω |
Install the IGCT fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 3 Relay Block and Junction Block Assembly |
| *2 | IGCT Relay |
Remove the IGCT relay from the No. 3 relay block and junction block assembly.
| *1 | IGCT Relay |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Auxiliary battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
Install the IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A29 and A30*1, G63*2 hybrid vehicle control ECU assembly connectors.
*1: for LHD
*2: for RHD
Remove the IGCT NO. 2 fuse from the No. 3 relay block and junction block assembly.
for LHD:
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | - | - |
| *1 | No. 3 Relay Block and Junction Block Assembly | *2 | IGCT NO. 2 Fuse |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-11 (+B1) - 2 (IGCT NO. 2 fuse terminal) | Always | Below 1 Ω |
| A30-1 (+B2) - 2 (IGCT NO. 2 fuse terminal) | Always | Below 1 Ω |
for RHD:
Measure the resistance according to the value(s) in the table below.
| *A | for RHD | - | - |
| *1 | No. 3 Relay Block and Junction Block Assembly | *2 | IGCT NO. 2 Fuse |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-11 (+B1) - 2 (IGCT NO. 2 fuse terminal) | Always | Below 1 Ω |
| G63-1 (+B2) - 2 (IGCT NO. 2 fuse terminal) | Always | Below 1 Ω |
Reconnect the A29 and A30*1, G63*2 hybrid vehicle control ECU assembly connectors.
*1: for LHD
*2: for RHD
Install the IGCT NO. 2 fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IGCT fuse, IGCT NO. 2 fuse and IGCT relay from the No. 3 relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *1 | No. 3 Relay Block and Junction Block Assembly | *2 | IGCT NO. 2 Fuse |
| *3 | IGCT Relay | *4 | IGCT Fuse |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IGCT relay) - 2 (IGCT fuse terminal) | Always | Below 1 Ω |
| 5 (IGCT relay) - 1 (IGCT NO. 2 fuse terminal) | Always | Below 1 Ω |
Install the IGCT fuse, IGCT NO. 2 fuse and IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A29 hybrid vehicle control ECU assembly connector.
Remove the IGCT relay from the No. 3 relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *1 | No. 3 Relay Block and Junction Block Assembly | *2 | IGCT Relay |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-5 (MREL) - 1 (IGCT relay) | Always | Below 1 Ω |
| A29-5 (MREL) or 1 (IGCT relay) - Body ground and other terminals | Always | 10 kΩ or higher |
Install the IGCT relay.
Reconnect the A29 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGCT relay from the No. 3 relay block and junction block assembly
| *1 | No. 3 Relay Block and Junction Block Assembly |
| *2 | IGCT Relay |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (IGCT relay) - Body ground | Always | Below 1 Ω |
Install the IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGCT NO. 2 fuse from the No. 3 relay block and junction block assembly.
Disconnect the A29 and A30*1, G63*2 hybrid vehicle control ECU assembly connectors.
*1: for LHD
*2: for RHD
for LHD:
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | - | - |
| *1 | No. 3 Relay Block and Junction Block Assembly | *2 | IGCT No. 2 Fuse |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-11 (+B1) or 2 (IGCT No. 2 fuse terminal) - Body ground and other terminals | Always | 10 kΩ or higher |
| A30-1 (+B2) or 2 (IGCT No. 2 fuse terminal) - Body ground and other terminals | Always | 10 kΩ or higher |
for RHD:
Measure the resistance according to the value(s) in the table below.
| *A | for RHD | - | - |
| *1 | No. 3 Relay Block and Junction Block Assembly | *2 | IGCT No. 2 Fuse |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-11 (+B1) or 2 (IGCT No. 2 fuse terminal) - Body ground and other terminals | Always | 10 kΩ or higher |
| G63-1 (+B2) or 2 (IGCT No. 2 fuse terminal) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the A29 and A30*1, G63*2 hybrid vehicle control ECU assembly connectors.
*1: for LHD
*2: for RHD
Install the IGCT No. 2 fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IGCT fuse, IGCT NO. 2 fuse and IGCT relay from the No. 3 relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *1 | No. 3 Relay Block and Junction Block Assembly | *2 | IGCT NO. 2 Fuse |
| *3 | IGCT Relay | *4 | IGCT Fuse |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IGCT relay) or 2 (IGCT fuse terminal) - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGCT relay) or 1 (IGCT No. 2 fuse terminal) - Body ground and other terminals | Always | 10 kΩ or higher |
Install the IGCT fuse, IGCT NO. 2 fuse and IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT