Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › REAR MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.02
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0390718 REAR MOTOR GENERATOR CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  REAR MOTOR GENERATOR CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P0C5513  Drive Motor "B" Position Sensor Circuit "A" Circuit Open  P0C551F  Drive Motor "B" Position Sensor Circuit "A" Circuit Intermittent  P0C5F13  Drive Motor "B" Position Sensor Circuit "B" Circuit Open  P0C5F1F  Drive Motor "B" Position Sensor Circuit "B" Circuit Intermittent  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs indicate that the resolver output signal is abnormal. The cause of this malfunction may be one of the following:


Area Main Malfunction Description
Inverter low-voltage circuit The connectors are not connected properly
Rear traction motor with transaxle assembly
·

Open circuit in the rear motor resolver circuit

·

Rear motor (MGR) internal malfunction (entry of foreign matter, etc.)


Wire harness between the resolver and inverter with converter assembly
·

Open circuit in the wire harness

·

The connectors are not connected properly


Inside of inverter Inverter with converter assembly internal circuit malfunction

DESCRIPTION

Refer to the system description for the Rear Motor Resolver Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>Rear Motor Resolver Circuit

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0C5513 Drive Motor "B" Position Sensor Circuit "A" Circuit Open Open in rear motor resolver sin phase signal circuit
(1 trip detection logic)
·

Wire harness or connector

·

Rear traction motor with transaxle assembly

·

Inverter with converter assembly


Comes on Master Warning:
Comes on
P0C551F Drive Motor "B" Position Sensor Circuit "A" Circuit Intermittent Open in rear motor resolver sin phase circuit detected when DTC P0C7917, P0D3319, P1C5D19, P1C5F19 or P1C5E19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Rear traction motor with transaxle assembly

·

Inverter with converter assembly


Does not come on Master Warning:
Does not come on
P0C5F13 Drive Motor "B" Position Sensor Circuit "B" Circuit Open Open in rear motor resolver cos phase signal circuit
(1 trip detection logic)
·

Wire harness or connector

·

Rear traction motor with transaxle assembly

·

Inverter with converter assembly


Comes on Master Warning:
Comes on
P0C5F1F Drive Motor "B" Position Sensor Circuit "B" Circuit Intermittent Open in rear motor resolver cos phase circuit detected when DTC P0C7917, P0D3319, P1C5D19, P1C5F19 or P1C5E19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Rear traction motor with transaxle assembly

·

Inverter with converter assembly


Does not come on Master Warning:
Does not come on

HINT:

If either of these DTCs is output, an open in the indicated circuit (sin or cos phase circuit) is suspected.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Turn the power switch on (READY) and wait for 5 seconds or more.

8.

Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.

9.

Drive the vehicle forward with the shift lever in D for 5 m (16 ft.) or more.

10.

Drive the vehicle backward with the shift lever in R for 5 m (16 ft.) or more.

11.

Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.

12.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.

·

If the resolver is malfunctioning, the vehicle may not drive smoothly.

·

When inspecting the connectors, if it is difficult to judge if a connector was disconnected, deformed or improperly secured, disconnect and reconnect the connector and then check for DTCs again. Check if the same DTC is output. If the same DTC is not output, improper connection of connectors is suspected.

·

As a malfunction detection threshold may be exceeded when performing the vibration or heat connector inspections, make sure to perform the following inspection to check that the DTC was not stored due to the malfunction of a part.



PROCEDURE

1.GO TO MOTOR GENERATOR CONTROL SYSTEM
a.

Go to Motor Generator Control System.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>P0C5513

HINT:

For the P0C5513, P0C551F, P0C5F13 and P0C5F1F inspection procedures, refer to the Motor Generator Control System section.



Result:
Result
NEXT



NEXT

END