Refer to DTC P003012.
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P003012
Although the DTC titles say O2 sensor, these DTCs relate to the air fuel ratio sensor (sensor 1).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P014C00 | O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 1 | The rich to lean response rate deterioration level* value is standard or less (2 trip detection logic). | ·
Air fuel ratio sensor (sensor 1) ·
Air fuel ratio sensor (sensor 1) heater ·
ECM |
Comes on | DTC stored | SAE Code: P014C |
| P014D00 | O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 1 | The lean to rich response rate deterioration level* value is standard or more (2 trip detection logic). | ·
Air fuel ratio sensor (sensor 1) ·
Air fuel ratio sensor (sensor 1) heater ·
ECM |
Comes on | DTC stored | SAE Code: P014D |
| P015A00 | O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1 | The rich to lean delay level* value is standard or more (2 trip detection logic). | ·
Air fuel ratio sensor (sensor 1) ·
Air fuel ratio sensor (sensor 1) heater ·
ECM |
Comes on | DTC stored | SAE Code: P015A |
| P015B00 | O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1 | The lean to rich delay level* value is standard or more (2 trip detection logic). | ·
Air fuel ratio sensor (sensor 1) ·
Air fuel ratio sensor (sensor 1) heater ·
ECM |
Comes on | DTC stored | SAE Code: P015B |
*: Calculated by ECM based on the air fuel ratio sensor (sensor 1) output.
After the engine has been warmed up, the ECM carries out air fuel ratio feedback control and maintains the air fuel ratio at the theoretical ratio. In addition, after all the preconditions have been met, active air fuel ratio control is performed for approximately 30 seconds. During active air fuel ratio control, the ECM measures the response of the air fuel ratio sensor (sensor 1) by increasing or decreasing a specific injection quantity based on the theoretical air fuel ratio learned during normal air fuel control. The ECM determines whether there is an air fuel ratio sensor (sensor 1) malfunction at the mid-point of active air fuel ratio control.
If the response of the air fuel ratio sensor (sensor 1) has decreased, DTC P014C00 and P014D00 are output.
If the air fuel ratio sensor (sensor 1) output timing is delayed, DTC P015A00 and P015B00 are output.
| Required Sensors/Components (Main) | Air fuel ratio sensor (sensor 1) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Active air fuel ratio control | Performing |
| Active air fuel ratio control is performed when the following conditions are met | - |
| Auxiliary battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Idle | Off |
| Engine speed | 1000 rpm or higher, and less than 4000 rpm |
| Air fuel ratio sensor (sensor 1) status | Activated |
| Fuel-cut | Off |
| Engine load | 10% or higher, and less than 70% |
| Catalyst monitor | Not yet |
| Mass air flow | 4.5 gm/sec or higher, and less than 15 gm/sec |
Performing this confirmation pattern will activate the air fuel ratio sensor (sensor 1) response monitor.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) [A].
Drive the vehicle at a constant speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the engine stops, further depress the accelerator pedal to restart the engine.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P014C00, P014D00, P015A00 or P015B00.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
Refer to DTC P003012.
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P003012
Inspect the fuses for circuits related to this system before performing the following procedure.
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
A low air fuel ratio sensor (sensor 1) current could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor (sensor 1) current could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P014C00, P014D00, P015A00 or P015B00 is output | A |
| DTC P014C00, P014D00, P015A00 or P015B00 and other DTCs are output | B |
If any DTCs other than P014C00, P014D00, P015A00 or P015B00 are output, troubleshoot those DTCs first.
A
B
Inspect the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air fuel ratio sensor (sensor 1) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C28-1 (HA1A) - C45-9 (HA1A) | Always | Below 1 Ω |
| C28-3 (A1A+) - C45-95 (A1A+) | Always | Below 1 Ω |
| C28-4 (A1A-) - C45-94 (A1A-) | Always | Below 1 Ω |
| C28-1 (HA1A) or C45-9 (HA1A) - Body ground and other terminals | Always | 10 kΩ or higher |
| C28-3 (A1A+) or C45-95 (A1A+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C28-4 (A1A-) or C45-94 (A1A-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P014C00, P014D00, P015A00 or P015B00 is output | B |
A
B
Replace the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P014C00, P014D00, P015A00 or P015B00 is output | B |
A
B
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P017100