Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P11EA00  Bank 1 Air-Fuel Ratio Imbalance (Port)  P11EC00  Cylinder #1 Air-Fuel Ratio Imbalance (Port)  P11ED00  Cylinder #2 Air-Fuel Ratio Imbalance (Port)  P11EE00  Cylinder #3 Air-Fuel Ratio Imbalance (Port)  P11EF00  Cylinder #4 Air-Fuel Ratio Imbalance (Port)  P219A00  Bank 1 Air-Fuel Ratio Imbalance  P219C00  Cylinder 1 Air-Fuel Ratio Imbalance  P219D00  Cylinder 2 Air-Fuel Ratio Imbalance  P219E00  Cylinder 3 Air-Fuel Ratio Imbalance  P219F00  Cylinder 4 Air-Fuel Ratio Imbalance  


DESCRIPTION

Refer to DTC P003012.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P003012

Refer to DTC P030000.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P030000

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P11EA00 Bank 1 Air-Fuel Ratio Imbalance (Port) The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P11EA
P11EC00 Cylinder #1 Air-Fuel Ratio Imbalance (Port) The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P11EC
P11ED00 Cylinder #2 Air-Fuel Ratio Imbalance (Port) The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P11ED
P11EE00 Cylinder #3 Air-Fuel Ratio Imbalance (Port) The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P11EE
P11EF00 Cylinder #4 Air-Fuel Ratio Imbalance (Port) The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P11EF
P219A00 Bank 1 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219A
P219C00 Cylinder 1 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219C
P219D00 Cylinder 2 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219D
P219E00 Cylinder 3 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219E
P219F00 Cylinder 4 Air-Fuel Ratio Imbalance The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Intake system

·

Gas leaks from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P219F

MONITOR DESCRIPTION

Fuel System Air Fuel Ratio Cylinder Imbalance Monitor

The ECM uses the air fuel ratio sensor (sensor 1) and crankshaft position sensor to monitor the difference in air fuel ratios between the cylinders caused by differences in injection volumes between the cylinders, leakage in the intake or exhaust system, etc.

When the air fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that there is a malfunction, illuminates the MIL and stores a DTC.


Air Fuel Ratio Sensor (Sensor 1) Monitoring Method: P11EA00 (for port injection), or P219A00 (for direct injection) is stored primarily when a rich side imbalance is detected.

When the system detects a difference in air fuel ratios between the cylinders due to fluctuation in the air fuel ratio sensor (sensor 1) output over 1 engine cycle (2 crankshaft revolutions), the system determines that there is a problem.


Crankshaft Position Sensor Monitoring Method: P11EC00, P11ED00, P11EE00 and/or P11EF00 (for port injection), or P219C00, P219D00, P219E00 and/or P219F00 (for direct injection) are stored primarily when a lean side imbalance is detected.

The system monitors the engine speed variation and when the variation becomes large, the system determines that there is a difference in air fuel ratios between the cylinders, which it determines to be a problem.


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor (sensor 1)
Crankshaft position sensor
Required Sensors/Components (Related) Mass air flow meter sub-assembly
Engine coolant temperature sensor
Vehicle speed sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

P11EA00: Air Fuel Ratio Sensor (Sensor 1) Monitoring Method
Air fuel ratio sensor (sensor 1) status Activated
Engine speed 1400 rpm or higher, and less than 2400 rpm
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Fuel system status Closed loop
Engine load 40% or higher, and less than 70%

P11EC00, P11ED00, P11EE00, P11EF00, P219C00, P219D00, P219E00 and P219F00: Crankshaft Position Sensor Monitoring Method (First Judgment)
Engine speed 1400 rpm or higher, and less than 2400 rpm
Engine coolant temperature 75°C (167°F) or higher
Air fuel ratio sensor (sensor 1) status Activated
Fuel system status Closed loop
Auxiliary battery voltage 11 V or higher

P11EC00, P11ED00, P11EE00, P11EF00, P219C00, P219D00, P219E00 and P219F00: Crankshaft Position Sensor Monitoring Method (Second Judgment)
Vehicle speed Less than 3 km/h (1.875 mph)
Engine speed 1050 rpm or higher, and less than 1350 rpm
Engine coolant temperature 75°C (167°F) or higher
Air fuel ratio sensor (sensor 1) status Activated
Fuel system status Closed loop
Auxiliary battery voltage 11 V or higher

P219A00: Air Fuel Ratio Sensor (Sensor 1) Monitoring Method
Air fuel ratio sensor (sensor 1) status Activated
Engine speed 1400 rpm or higher, and less than 2400 rpm
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Fuel system status Closed loop
Engine load 40% or higher, and less than 70%

TYPICAL MALFUNCTION THRESHOLDS

P11EA00: Air Fuel Ratio Sensor (Sensor 1) Monitoring Method
Air fuel ratio sensor (sensor 1) monitoring method criteria (rich side imbalance for port injection) 1 or more

P11EC00, P11ED00, P11EE00 and P11EF00: Crankshaft Position Sensor Monitoring Method (First Judgment)
Crankshaft position sensor monitoring method criteria (lean side imbalance for port injection) (first Judgment) 1.5 or more

P11EC00, P11ED00, P11EE00 and P11EF00: Crankshaft Position Sensor Monitoring Method (Second Judgment)
Crankshaft position sensor monitoring method criteria (lean side imbalance for port injection) (second judgment) 1 or more

P219A00: Air Fuel Ratio Sensor (Sensor 1) Monitoring Method
Air fuel ratio sensor (sensor 1) monitoring method criteria (rich side imbalance for direct injection) 1 or more

P219C00, P219D00, P219E00 and P219F00: Crankshaft Position Sensor Monitoring Method (First Judgment)
Crankshaft position sensor monitoring method criteria (lean side imbalance for direct injection) (first Judgment) 1.5 or more

P219C00, P219D00, P219E00 and P219F00: Crankshaft Position Sensor Monitoring Method (Second Judgment)
Crankshaft position sensor monitoring method criteria (lean side imbalance for direct injection) (second judgment) 1 or more

CONFIRMATION DRIVING PATTERN

A288663E09
4.729,3.51 4.427,3.51 false 4.427,3.5 4.083,2.625 false 5.167,3.156 4.573,3.156 false 5,3.156 4.896,2.635 false 4.573,3.146 4.406,2.625 false 1.875,2.625 1.979,3.125 false 1.979,3.115 2.563,3.115 false 2.448,3.115 2.375,2.615 false 1.563,2.646 1.729,3.49 false 1.729,3.479 1.885,3.479 false 1.813,0.781 2.167,0.958 0.354,0.177 10 false [C]* 0.083,2.438 0.958,2.792 0.875,0.354 10 false Power Switch off 0.583,2.146 1.073,2.5 0.49,0.354 10 false Idling 0.406,1.51 0.979,1.708 0.573,0.198 10 false 40 km/h 0.385,0.917 0.958,1.125 0.573,0.208 10 false 80 km/h 0.313,0.646 0.938,0.917 0.625,0.271 10 false 100 km/h 1.073,2.042 1.563,2.313 0.49,0.271 10 false [A] 1.219,1.135 1.531,1.333 0.313,0.198 10 false [B]* 2.313,2.031 2.833,2.333 0.521,0.302 10 false [D] 3.063,0.792 3.396,0.99 0.333,0.198 10 false [E]* 3.76,0.76 4.104,0.969 0.344,0.208 10 false [G]* 4.333,0.49 4.677,0.719 0.344,0.229 10 false [H]* 3.76,3.167 4.052,3.417 0.292,0.25 10 false [F] 4.844,2.042 5.219,2.323 0.375,0.281 10 false [I] 5.573,0.49 5.885,0.719 0.313,0.229 10 false [J]* 6.542,3.167 6.906,3.417 0.365,0.25 10 false [K] 0.073,0.052 1,0.448 0.927,0.396 10 false Vehicle Speed 6.781,2.583 7.135,2.906 0.354,0.323 10 false Time 1.917,3.396 3.156,3.719 1.24,0.323 10 false 10 to 20 seconds 2.573,3.021 3.844,3.344 1.271,0.323 10 false 1 minute or more 4.76,3.438 5.844,3.76 1.083,0.323 10 false 5 to 15 seconds 5.219,3.083 6.302,3.385 1.083,0.302 10 false 1 minute or more 0.208,3.396 1.365,3.594 1.156,0.198 10 false *: Engine running

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

7.

With the engine running, drive the vehicle at 40 km/h (25 mph) or higher.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


8.

With the engine running, gradually accelerate the vehicle from 40 km/h (25 mph) to 80 km/h (50 mph) taking approximately 10 to 20 seconds [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Refer to engine load and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 80 km/h (50 mph).

·

If the engine stops, further depress the accelerator pedal to restart the engine.



9.

With the engine running, drive the vehicle at 80 km/h (50 mph) or more for 1 minute or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Electrical load can be applied while the vehicle is driven.

·

If the engine stops, further depress the accelerator pedal to restart the engine.



10.

Idle the engine for 1 minute or more [D].

HINT:

Perform this step with the shift lever in D.


11.

Repeat steps [B] and [D] above at least 3 times [E].

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

With the engine running, drive the vehicle at 80 km/h (50 mph).

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


15.

With the engine running, gradually accelerate the vehicle from 80 km/h (50 mph) to 100 km/h (62 mph) taking approximately 5 to 15 seconds [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Refer to engine load and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 100 km/h (62 mph).

·

If the engine stops, further depress the accelerator pedal to restart the engine.



16.

With the engine running, drive the vehicle at 100 km/h (62 mph) or more for 1 minute or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Electrical load can be applied while the vehicle is driven.

·

If the engine stops, further depress the accelerator pedal to restart the engine.



17.

Idle the engine for 1 minute or more [I].

HINT:

Perform this step with the shift lever in D.


18.

Repeat steps [G] and [I] above at least 2 times [J].

19.

Enter the following menus: Powertrain / Engine / Trouble Codes [K].

20.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



21.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

22.

Input the DTC: P11EA00, P11EC00, P11ED00, P11EE00, P11EF00, P11F000, P219A00, P219C00, P219D00, P219E00 or P219F00.

23.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform the confirmation driving pattern and check the judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.

·

Whether malfunctions occur on the port injection side or direct injection side cannot be determined solely by the output DTCs. Inspect every suspected area even if it is not related to the DTCs.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P11EA00, P11EC00, P11ED00, P11EE00, P11EF00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 is output A
DTC P11EA00, P11EC00, P11ED00, P11EE00, P11EF00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 and other DTCs are output B


HINT:

If any DTCs other than DTC P11EA00, P11EC00, P11ED00, P11EE00, P11EF00, P219A00, P219C00, P219D00, P219E00 and/or P219F00 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (FREEZE FRAME DATA)

B

2.READ VALUE USING GTS (FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>FREEZE FRAME DATA

Freeze Frame Data Items for DTC P11EA00, P11EC00, P11ED00, P11EE00, P11EF00, P219A00, P219C00, P219D00, P219E00 or P219F00
·

Vehicle Speed

·

Engine Speed

·

Calculate Load

·

Short FT B1S1

·

Long FT B1S1

·

Misfire Count Cylinder #1 to #4


HINT:

When the sum of Short FT B1S1 and Long FT B1S1 is positive, the engine is running lean, and when the sum is negative, the engine is running rich.

Air Fuel Ratio Sensor (Sensor 1) Monitoring Method (P11EA00 and P219A00) Crankshaft Position Sensor Monitoring Method (P11EC00, P11ED00, P11EE00, P11EF00, P219C00, P219D00, P219E00 and P219F00) Note
DTCs are output DTC is output (Only one DTC relating to a single cylinder is output) Malfunctioning of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected
DTCs are output DTCs are output (Multiple DTCs relating to multiple cylinders are output) Malfunctioning of cylinders except ones detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.*
DTCs are not output DTCs are output Malfunctioning of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.
DTCs are output DTCs are not output Malfunctioning of the bank detected by the Air Fuel Ratio Sensor (Sensor 1) Monitoring Method is primarily suspected.

*: When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.



Result:
Proceed to
NEXT



NEXT

3.READ DTC OUTPUT
3.READ DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

HINT:
·

If any misfire count (Misfire Count Cylinder #1 to #4) increases while idling or driving the vehicle, proceed to step 6 (CHECK INTAKE SYSTEM).

·

Perform inspections while focusing on the cylinder whose misfire count has increased.




e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P11EA00 or P219A00 is output A
DTC P219A00 and P219C00, P219D00, P219E00 or P219F00 is output B
DTC P11EA00 and P11EC00, P11ED00, P11EE00 or P11EF00 is output
DTC P11EC00, P11ED00, P11EE00, P11EF00, P219C00, P219D00, P219E00 and/or P219F00 is output




A

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)

B

6.CHECK INTAKE SYSTEM
4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off and the shift lever should be in P or N.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / Coolant Temperature and Misfire Count Cylinder #1 to #4.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume
Data List Display
Coolant Temperature
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
50004 372 7 205,148,149,150,151
HINT:

When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 6 (CHECK INTAKE SYSTEM).



g.

Perform the Control the Injection Volume operation with the engine idling.


h.

Check the misfire counts (Misfire Count Cylinder #1 to #4) while decreasing the injection volume in 5% increments.

Result:

The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.



Result:
Proceed to
NEXT



NEXT

5.CHECK FOR EXHAUST GAS LEAK
5.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leaks in exhaust system.



HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

6.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE EXHAUST SYSTEM

6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>A25A-FXS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in the intake system.



HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

7.INSPECT SPARK PLUG

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.INSPECT SPARK PLUG
a.

Inspect the spark plug of the cylinder causing the imbalance.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION


HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

8.CHECK FOR SPARK (SPARK TEST)

NG

8.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

9.CHECK CYLINDER COMPRESSION PRESSURE
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

10.CHECK PORT FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.CHECK PORT FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE
a.

Check the port fuel injector assembly injection [whether fuel volume is high or low, and whether injection pattern is poor].

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL INJECTOR (for Port Injection)>INSPECTION


HINT:

Perform "Inspection After Repair" after replacing the port fuel injector assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

11.CHECK DIRECT FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE

NG

11.CHECK DIRECT FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE

HINT:

Perform "Inspection After Repair" after replacing the direct fuel injector assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

12.CHECK FOR CAUSE OF FAILURE

NG

12.CHECK FOR CAUSE OF FAILURE
a.

If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.


b.

Check the intake valve for deposits.

HINT:

As the DTC may have been stored due to deposits on the intake valve, remove the cylinder head sub-assembly and check the intake valve.



Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:

DTCs are not output.



Result:
Proceed to
NEXT



NEXT

END