Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P21CF13  Cylinder 1 Injector "B" Circuit Open  P21D013  Cylinder 2 Injector "B" Circuit Open  P21D113  Cylinder 3 Injector "B" Circuit Open  P21D213  Cylinder 4 Injector "B" Circuit Open  


DESCRIPTION

The D-4S system has two injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is an intake port injection system. The ECM determines the percentage of direct injection and port injection necessary in accordance with the engine speed and load.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P21CF13 Cylinder 1 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code: P21CF
P21D013 Cylinder 2 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code: P21D0
P21D113 Cylinder 3 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code: P21D1
P21D213 Cylinder 4 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code: P21D2

MONITOR DESCRIPTION

The ECM monitors the injection control of the port fuel injector assemblies. If a malfunction is detected in a port fuel injector assembly circuit, the ECM cancels the injection control for the corresponding cylinder, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Port fuel injector assembly (cylinder 1 to 4)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine [A].

10.

Idle the engine for 3 minutes or more [B].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P21CF13, P21D013, P21D113 or P21D213.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A409166E07
0.521,0.99 1.75,1.188 1.229,0.198 10 false IG2 MAIN 1.354,1.583 2.583,1.781 1.229,0.198 10 false IG2 NO. 1 2.406,1 3.635,1.198 1.229,0.198 10 false INJ 0.948,4.271 2.177,4.469 1.229,0.198 10 false G54 0.938,4.448 2.74,4.917 1.802,0.469 10 false Certification ECU (Smart Key ECU Assembly) 0.396,5.073 1.625,5.271 1.229,0.198 10 false MAIN 0.583,6.073 1.813,6.271 1.229,0.198 10 false Auxiliary Battery 1.833,3.865 3.063,4.063 1.229,0.198 10 false IG1D 2.25,3.75 2.625,3.938 0.375,0.188 10 false 17 1.198,1.146 1.573,1.333 0.375,0.188 10 false 2 1.99,1.156 2.365,1.344 0.375,0.188 10 false 1 1.208,0.75 1.583,0.938 0.375,0.188 10 false 5 2,0.75 2.375,0.938 0.375,0.188 10 false 3 3.563,0.969 3.979,1.125 0.417,0.156 10 false E1 3.563,1.146 5.302,1.594 1.74,0.448 10 false Port Fuel Injector Assembly (No. 1 Cylinder) 3.563,2.156 5.302,2.604 1.74,0.448 10 false Port Fuel Injector Assembly (No. 2 Cylinder) 3.563,3.167 5.302,3.615 1.74,0.448 10 false Port Fuel Injector Assembly (No. 3 Cylinder) 3.552,4.167 5.292,4.615 1.74,0.448 10 false Port Fuel Injector Assembly (No. 4 Cylinder) 3.563,1.969 3.979,2.125 0.417,0.156 10 false E2 3.583,2.979 4,3.135 0.417,0.156 10 false E3 3.552,3.99 3.969,4.146 0.417,0.156 10 false E4 5.448,0.865 5.865,1.021 0.417,0.156 10 false C45 5.458,4.896 5.875,5.052 0.417,0.156 10 false A24 5.51,0.667 5.938,0.844 0.427,0.177 10 false 76 5.5,1.667 5.927,1.844 0.427,0.177 10 false 75 5.479,2.688 5.906,2.865 0.427,0.177 10 false 74 5.521,3.677 5.948,3.854 0.427,0.177 10 false 73 5.51,4.698 5.938,4.875 0.427,0.177 10 false 10 6.25,6.052 6.667,6.208 0.417,0.156 10 false ECM 5.844,0.76 6.229,0.938 0.385,0.177 10 false #10 5.844,1.771 6.229,1.948 0.385,0.177 10 false #20 5.844,2.771 6.229,2.948 0.385,0.177 10 false #30 5.854,3.781 6.24,3.958 0.385,0.177 10 false #40 5.844,4.792 6.229,4.969 0.385,0.177 10 false E1 6.667,2.615 6.875,2.875 0.208,0.26 10 false IC 4.792,0.76 5.177,0.938 0.385,0.177 10 false 2 4.802,1.771 5.188,1.948 0.385,0.177 10 false 2 4.802,2.771 5.188,2.948 0.385,0.177 10 false 2 4.802,3.781 5.188,3.958 0.385,0.177 10 false 2 3.854,0.76 4.24,0.938 0.385,0.177 10 false 1 3.844,1.76 4.229,1.938 0.385,0.177 10 false 1 3.844,2.771 4.229,2.948 0.385,0.177 10 false 1 3.854,3.781 4.24,3.958 0.385,0.177 10 false 1 5.448,1.875 5.865,2.031 0.417,0.156 10 false C45 5.448,2.875 5.865,3.031 0.417,0.156 10 false C45 5.448,3.885 5.865,4.042 0.417,0.156 10 false C45

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTCS OUTPUT (IN ADDITION TO DTC P21CF13, P21D013, P21D113 OR P21D213)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P21CF13, P21D013, P21D113 or P21D213 is output A
DTC P21CF13, P21D013, P21D113 and P21D213 are output B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - PORT FUEL INJECTOR ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)
A402432C77
0.417,0.656 0.75,0.896 0.333,0.24 0.427,0.948 0.74,1.156 0.313,0.208 0.417,1.198 0.75,1.396 0.333,0.198 0.427,1.448 0.75,1.698 0.323,0.25 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 0.49,0.698 0.802,0.896 0.313,0.198 10 false E1 0.5,0.979 0.813,1.177 0.313,0.198 10 false E2 0.5,1.219 0.813,1.417 0.313,0.198 10 false E3 0.5,1.49 0.958,1.688 0.458,0.198 10 false E4
*a Front view of wire harness connector
(to Port Fuel Injector Assembly)


a.

Disconnect the port fuel injector assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below

Standard Voltage:
Tester Connection Condition Specified Condition
E1-1 - Body ground Power switch on (IG) 11 to 14 V
E2-1 - Body ground Power switch on (IG) 11 to 14 V
E3-1 - Body ground Power switch on (IG) 11 to 14 V
E4-1 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - PORT FUEL INJECTOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the port fuel injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-2 - C45-76 (#10) Always Below 1 Ω
E2-2 - C45-75 (#20) Always Below 1 Ω
E3-2 - C45-74 (#30) Always Below 1 Ω
E4-2 - C45-73 (#40) Always Below 1 Ω
E1-2 or C45-76 (#10) - Body ground and other terminals Always 10 kΩ or higher
E2-2 or C45-75 (#20) - Body ground and other terminals Always 10 kΩ or higher
E3-2 or C45-74 (#30) - Body ground and other terminals Always 10 kΩ or higher
E4-2 or C45-73 (#40) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)
a.

HINT:

Perform "Inspection After Repair" after replacing the port fuel injector assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

NG