Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2019.02–2020.05
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P013616  A/F (O2) Sensor Circuit Bank 1 Sensor 2 Circuit Current (Voltage) Below Threshold  


DESCRIPTION

Refer to DTC P003612.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P003612

HINT:

Although the DTC title say O2 sensor, this DTC relate to the air fuel ratio sensor (sensor 2).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P013616 A/F (O2) Sensor Circuit Bank 1 Sensor 2 Circuit Current (Voltage) Below Threshold Either of the following conditions is met (2 trip detection logic).
·

During active rich air-fuel ratio control, the air fuel ratio sensor (sensor 2) current is 6 mA or more

·

During active rich air-fuel ratio control, the oxygen storage capacity of the catalyst is more than 1.4 g when the air fuel ratio sensor (sensor 2) current is -0.25696 mA or higher


·

Air fuel ratio sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

EGR valve assembly

·

Fuel system

·

Intake system


Comes on (Euro- OBD) / Does not come on (Except Euro- OBD) DTC stored (Euro-OBD) / - (Except Euro-OBD) SAE Code: P0136

MONITOR DESCRIPTION

Active Air fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensors output indicates a near stoichiometric air fuel ratio. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and any malfunctions of the air fuel ratio sensor (sensor 2) (refer to the diagram below).

Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Air Fuel Ratio Sensor (Sensor 2) Output Current (DTC P013616)


Case 1: The ECM illuminates the MIL and stores a DTC when active rich air-fuel ratio control is being performed and the air fuel ratio sensor (sensor 2) current is 6 mA or more.

Case 2: The ECM illuminates the MIL and stores a DTC when active rich air-fuel ratio control is being performed, the oxygen storage capacity of the catalyst is more than 1.4 g and the air fuel ratio sensor (sensor 2) current is -0.25696 mA or more.

A392731E02
4.302,4.01 4.948,3.656 true 4.229,2.385 5.021,2.594 true 6.042,3.792 6.583,4.344 true 6.042,3.792 6.677,3.083 true 0.146,0.177 5.781,0.51 5.635,0.333 10 false Air Fuel Ratio Sensor (Sensor 2) Output Current Malfunction (P013616) 0.073,1.063 1.375,1.479 1.302,0.417 10 false Active Air Fuel Ratio Control 4.573,0.844 5.208,1.052 0.635,0.208 10 false Operation 0.031,2.927 1.365,3.5 1.333,0.573 10 false Air Fuel Ratio Sensor (Sensor 2) Output Current 0.063,4.448 1.115,4.958 1.052,0.51 10 false Oxygen Storage Capacity 3.813,3.927 4.354,4.198 0.542,0.271 10 false Normal 3.052,2.292 4.333,2.625 1.281,0.333 10 false Abnormal (Case 1) 0.063,1.917 1.5,2.167 1.438,0.25 10 false Fuel Injection Volume 1.74,1.677 2.427,1.969 0.688,0.292 10 false Increase 1.688,2.156 2.552,2.406 0.865,0.25 10 false Decrease 1.552,2.594 2.292,3.042 0.74,0.448 10 false Malfunction Threshold 1.594,3.479 2.229,3.969 0.635,0.49 10 false Normal Threshold 5.385,3.708 6.01,4.094 0.625,0.385 10 false Abnormal (Case 2) 1.583,4.323 2.302,4.729 0.719,0.406 10 false Malfunction Threshold


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor (sensor 2)
Required Sensors/Components (Related) Crankshaft position sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Throttle position sensor
Air fuel ratio sensor (sensor 1)
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Auxiliary battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor (sensor 1) status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 80%

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met A and B
A. Continuous time of active rich air fuel ratio control*1 0 seconds or more
*1: Target air fuel ratio 13.7 or less
B. Either of the following conditions is met (a) or (b)
(a) Air fuel ratio sensor (sensor 2) current 6 mA or more
(b) OSC (Oxygen Storage Capacity) of catalyst More than 1.4 g

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used for the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the air fuel ratio sensor (sensor 2) monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A264212E41
1.74,2.427 1.563,2.802 1.563,2.802 1.417,2.802 false 4.021,0.719 4.25,0.875 0.229,0.156 10 false [C] 3.49,2.906 4.729,3.063 1.24,0.156 10 false 10 minutes or more 0.563,1.365 1.615,1.802 1.052,0.438 10 false 75 km/h [Engine running] 2.042,2.417 2.406,2.646 0.365,0.229 10 false [A] 0.479,0.479 1.594,0.979 1.115,0.5 10 false 120 km/h [Engine running] 1.25,2.229 1.698,2.49 0.448,0.26 10 false Idling 0.063,2.74 1.396,2.896 1.333,0.156 10 false Power Switch on (IG) 2.677,2.135 3.063,2.406 0.385,0.271 10 false [B] 2.333,2.917 3.135,3.073 0.802,0.156 10 false Warming up 5.01,3.313 5.24,3.469 0.229,0.156 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P [B].

10.

Drive the vehicle at 75 to 120 km/h (46 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P013616.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [C] through [D] again.




CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Active Test "Control the Injection Volume for A/F Sensor". This Active Test can help to determine whether the air fuel ratio sensors (sensor 1 and sensor 2) and other potential trouble areas are malfunctioning.

The following procedure describes how to perform the Active Test "Control the Injection Volume for A/F Sensor" using the GTS.


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

5.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

6.

Idle the engine for 5 minutes or more with the shift lever in P.

7.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2.

8.

Perform the Active Test with the engine idling (change the fuel injection volume).

9.

Monitor the output current of the air fuel ratio sensor (sensor 1) (A/F (O2) Sensor Current B1S1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S2) displayed on the GTS.


HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

Each sensor reacts in accordance with the increase and decrease in the fuel injection volume.



Standard
GTS Display (Sensor) Injection Volume Status Current
A/F (O2) Sensor Current B1S1
(Air fuel ratio sensor (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean More than 0.037 mA
A/F (O2) Sensor Current B1S2
(Air fuel ratio sensor (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean More than 0.33 mA

NOTICE:

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


A392732E02
0.135,0.802 0.531,1.01 0.396,0.208 10 false Case 0.906,0.688 2.958,1.115 2.052,0.427 10 false Air Fuel Ratio Sensor (Sensor 1) Output Current 3.542,0.708 5.594,1.115 2.052,0.406 10 false Air Fuel Ratio Sensor (Sensor 2) Output Current 5.99,0.729 6.99,1.104 1,0.375 10 false Main Suspected Trouble Area 0.24,2.24 0.563,2.448 0.323,0.208 10 false 1 0.667,1.385 1.896,1.583 1.229,0.198 10 false Injection Volume 1.417,1.729 1.969,1.948 0.552,0.219 10 false 12.5% 1.365,1.938 2.021,2.156 0.656,0.219 10 false -12.5% 0.688,2.354 1.823,2.594 1.135,0.24 10 false Output Current 0.635,2.729 1.99,2.958 1.354,0.229 10 true More than 0.037 mA 0.833,2.958 1.906,3.167 1.073,0.208 10 true Below -0.075 mA 2.677,2.865 3.083,3.052 0.406,0.188 10 false OK 5.302,2.844 5.708,3.031 0.406,0.188 10 false OK 3.375,2.344 4.5,2.552 1.125,0.208 10 false Output Current 3.292,2.656 4.833,2.875 1.542,0.219 10 false More than 0.33 mA 3.49,2.938 4.75,3.167 1.26,0.229 10 false Below -0.86 mA 6.385,2.302 6.708,2.51 0.323,0.208 10 false - 0.229,4.365 0.552,4.573 0.323,0.208 10 false 2 5.25,4.906 5.656,5.094 0.406,0.188 10 false OK 2.667,4.833 3.073,5.021 0.406,0.188 10 false NG 0.625,4.823 2.094,5.083 1.469,0.26 10 false Almost no reaction 5.896,3.615 7.094,4.021 1.198,0.406 10 false Air fuel ratio sensor (sensor 1) 5.885,4.198 7.094,4.563 1.208,0.365 10 false Air fuel ratio sensor (sensor 1) heater 5.885,4.833 7.083,5.208 1.198,0.375 10 false Air fuel ratio sensor (sensor 1) circuit 5.802,3.615 6.125,3.823 0.323,0.208 10 false - 5.802,4.198 6.125,4.406 0.323,0.208 10 false - 5.792,4.833 6.115,5.042 0.323,0.208 10 false - 5.26,6.885 5.667,7.073 0.406,0.188 10 false NG 2.688,7 3.094,7.188 0.406,0.188 10 false OK 5.802,5.677 6.135,5.885 0.333,0.208 10 false - 5.792,6.281 6.125,6.49 0.333,0.208 10 false - 5.792,6.885 6.125,7.094 0.333,0.208 10 false - 5.24,8.948 5.646,9.135 0.406,0.188 10 false NG 2.646,8.948 3.052,9.135 0.406,0.188 10 false NG 6.021,7.969 6.99,8.292 0.969,0.323 10 false Fuel system 6.01,8.552 7.052,9.344 1.042,0.792 10 false Gas leak from exhaust system 5.917,7.969 6.25,8.177 0.333,0.208 10 false - 5.906,8.563 6.24,8.771 0.333,0.208 10 false - 3.344,1.385 4.573,1.583 1.229,0.198 10 false Injection Volume 0.677,3.469 1.906,3.667 1.229,0.198 10 false Injection Volume 3.333,3.49 4.563,3.688 1.229,0.198 10 false Injection Volume 0.698,4.354 1.833,4.594 1.135,0.24 10 false Output Current 3.406,4.354 4.531,4.563 1.125,0.208 10 false Output Current 3.313,4.771 4.854,4.99 1.542,0.219 10 false More than 0.33 mA 3.521,5.052 4.781,5.281 1.26,0.229 10 false Below -0.86 mA 3.26,6.865 4.729,7.125 1.469,0.26 10 false Almost no reaction 0.667,5.552 1.896,5.75 1.229,0.198 10 false Injection Volume 3.313,5.542 4.542,5.74 1.229,0.198 10 false Injection Volume 0.708,7.615 1.938,7.813 1.229,0.198 10 false Injection Volume 3.323,7.615 4.552,7.813 1.229,0.198 10 false Injection Volume 0.646,8.917 2.115,9.177 1.469,0.26 10 false Almost no reaction 3.292,8.917 4.76,9.177 1.469,0.26 10 false Almost no reaction 0.729,6.479 1.865,6.719 1.135,0.24 10 false Output Current 0.708,8.542 1.844,8.781 1.135,0.24 10 false Output Current 3.385,6.438 4.51,6.646 1.125,0.208 10 false Output Current 3.406,8.542 4.531,8.75 1.125,0.208 10 false Output Current 5.896,5.667 7.094,6.073 1.198,0.406 10 false Air fuel ratio sensor (sensor 2) 5.875,6.281 7.083,6.646 1.208,0.365 10 false Air fuel ratio sensor (sensor 2) heater 5.875,6.885 7.073,7.26 1.198,0.375 10 false Air fuel ratio sensor (sensor 2) circuit 4.031,1.688 4.583,1.906 0.552,0.219 10 false 12.5% 4,1.906 4.656,2.125 0.656,0.219 10 false -12.5% 1.396,3.771 1.948,3.99 0.552,0.219 10 false 12.5% 1.354,3.969 2.01,4.188 0.656,0.219 10 false -12.5% 4,3.781 4.552,4 0.552,0.219 10 false 12.5% 3.958,3.979 4.615,4.198 0.656,0.219 10 false -12.5% 1.396,5.833 1.948,6.052 0.552,0.219 10 false 12.5% 1.354,6.031 2.01,6.25 0.656,0.219 10 false -12.5% 3.958,5.854 4.51,6.073 0.552,0.219 10 false 12.5% 3.917,6.052 4.573,6.271 0.656,0.219 10 false -12.5% 1.385,7.875 1.938,8.094 0.552,0.219 10 false 12.5% 1.333,8.083 1.99,8.302 0.656,0.219 10 false -12.5% 3.948,7.885 4.5,8.104 0.552,0.219 10 false 12.5% 3.906,8.094 4.563,8.313 0.656,0.219 10 false -12.5% 0.229,6.365 0.552,6.573 0.323,0.208 10 false 3 0.24,8.406 0.563,8.615 0.323,0.208 10 false 4 0.625,6.844 1.969,7.052 1.344,0.208 10 true More than 0.037 mA 0.823,7.083 1.885,7.313 1.063,0.229 10 true Below -0.075 mA

Performing the Active Test "Control the Injection Volume for A/F Sensor" allows the output value of the air fuel ratio sensors (sensor 1 and sensor 2) to be checked and graphed.

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (IN ADDITION TO DTC P013616)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P013616 is output A
DTC P013616 and other DTCs are output B


HINT:

If any DTCs other than P013616 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Idle the engine for 5 minutes or more with the shift lever in P.


g.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / Coolant Temperature, A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temperature
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B1S2
50004 372 8 205,230,564

h.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


i.

Monitor the output values of the air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output value does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard
GTS Display (Sensor) Injection Volume Status Current
A/F (O2) Sensor Current B1S1
(Air fuel ratio (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean More than 0.037 mA
A/F (O2) Sensor Current B1S2
(Air fuel ratio (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean More than 0.33 mA

Result:
Status of A/F (O2) Sensor Current B1S1 Status of A/F (O2) Sensor Current B1S2 Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich
·

Air fuel ratio sensor (sensor 2)


A
Lean Lean
·

Gas leak from exhaust system

·

EGR valve assembly

·

Extremely lean actual air fuel ratio

·

Air fuel ratio sensor (sensor 2)


B
Rich Rich
·

Gas leak from exhaust system

·

EGR valve assembly

·

Extremely rich actual air fuel ratio

·

Air fuel ratio sensor (sensor 2)


Lean/Rich Lean
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


C
Lean/Rich Rich
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


Lean Lean/Rich
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)


D
Rich Lean/Rich
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)




Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently more than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently more than 0.33 mA.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently below -0.86 mA.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B1S2].

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DATA LIST / ACTIVE TEST




A

3.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

B

6.CHECK FOR EXHAUST GAS LEAK

C

10.CHECK FOR EXHAUST GAS LEAK

D

11.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
3.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)
a.

Replace the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P013616.


d.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions




Result:
Proceed to
NEXT



NEXT

END

6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



f.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Intake Manifold Absolute Pressure, Coolant Temperature and Engine Independent.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
Coolant Temperature
Engine Independent
50004 372 25 385,205,428

g.

Confirm that the value of Data List item Engine Independent is "Operate" then check the value of Intake Manifold Absolute Pressure while performing the Active Test.

NOTICE:
·

Make sure that the value of Data List item Engine Independent is "Operate" while performing the Active Test.

·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Intake Manifold Absolute Pressure
(Data List)
(EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.




Result:
Proceed to
OK
NG



OK

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

8.INSPECT EGR VALVE ASSEMBLY
8.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P017100 and P017200 Inspection Procedure.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P017100


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
10.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



HINT:
·

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION

·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

11.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
a.

Replace the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P013616)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P013616)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P013616.


d.

Check that the DTC judgment result is NORMAL. If the DTC judgment result is INCOMPLETE, perform the confirmation drive pattern again but increase the vehicle speed.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P013616 is output)
B



HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

END

B

REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)