Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2019.02–2020.05
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372717 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P26CA14  Engine Coolant Pump Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P26CA12.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P26CA12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P26CA14 Engine Coolant Pump Circuit Short to Ground or Open The operation duty ratio (WPO) of the monitoring engine water pump assembly becomes a certain amount or less when engine water pump assembly operation command is output (1 trip detection logic).
·

Open or short in engine water pump assembly (water inlet housing) circuit

·

Engine water pump assembly (water inlet housing)

·

ECM


Comes on DTC stored SAE Code: P26CC

Related Data List
DTC No. Data List
P26CA14
·

Coolant Temperature

·

Electric Water Pump Target Speed

·

Electric Water Pump Speed



MONITOR DESCRIPTION

The ECM outputs an operation duty signal (WPO) to steplessly control the speed of the engine water pump assembly. The ECM outputs an operation duty signal (WPO) to the engine water pump assembly and monitors the actual duty signal (WPO) being output. When the operation duty signal (WPO) is being output to the engine water pump assembly and the actual operation duty signal (WPO) is a certain value or less, the ECM detects a malfunction and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Engine water pump assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and maintain the engine speed at 2500 rpm or more for at least 40 seconds [B].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P26CA14.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ECM (INTERNAL CIRCUIT)
A436572C03
0.396,0.969 0.74,1.26 0.344,0.292 1.292,1.823 1.667,1.073 true 0.458,1.031 0.917,1.229 0.458,0.198 10 false C23 0.135,0.135 0.594,0.333 0.458,0.198 10 false *a 1.135,1.875 1.594,2.073 0.458,0.198 10 false SWP
*a Front view of wire harness connector
(to Engine Water Pump Assembly (Water Inlet Housing))


a.

Disconnect the engine water pump assembly (water inlet housing) connector.


b.

Turn the power switch on (IG).


c.

Measure the resistance according to the value(s) in the table below.

Standard:
Tester Connection Condition Specified Condition
C23-2 (SWP) - Body ground Power switch on (IG) Resistance fluctuates*


HINT:
·

*: When the connector of the engine water pump assembly is disconnected, the ECM will enter fail-safe mode. When the ECM is in fail-safe mode, a continuous duty signal will be output and the resistance will fluctuate as the transistor inside the ECM is turned on an off.

·

If the resistance fluctuates while the ECM is in fail-safe mode after the connector of the engine water pump assembly is disconnected, it can be determined that the transistor is operating.

·

If the transistor does not operate, the ECM may be malfunctioning.

·

If the resistance fluctuates after turning the power switch on (IG), it can be determined that the ECM is in fail-safe mode.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING) - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING) - ECM)
a.

Disconnect the engine water pump assembly (water inlet housing) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C23-2 (SWP) - C45-50 (WPO) Always Below 1 Ω
C23-2 (SWP) or C45-50 (WPO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR