Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › from 2019.02
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check Bus 1 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus wire and/or CAN branch wire when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area

*1: w/ Pre-collision System

*2: w/ Blind Spot Monitor System

*3: w/ Panoramic View Monitor System

*4: w/ TOYOTA Parking Assist-sensor System

*5: w/ Grille Shutter System

*6: w/ Parking Assist Monitor System

Resistance between terminals 23 (CA1H) and 8 (CA1L) of central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus wire

·

Short in CAN branch wire

·

Central gateway ECU (network gateway ECU)

·

Forward recognition camera*1

·

Millimeter wave radar sensor assembly*1

·

Blind spot monitor sensor LH*2

·

Parking assist ECU*3

·

Television camera assembly*3, *6

·

Clearance warning ECU assembly*4

·

Swing grille actuator assembly*5

·

Radiator shutter sub-assembly*5

·

No. 2 CAN junction connector

·

No. 8 CAN junction connector

·

No. 1 CAN junction terminal



WIRING DIAGRAM

C414777E01
0.229,1.042 2.25,1.271 2.021,0.229 10 false No. 1 CAN Junction Terminal 0.24,2.354 2.281,2.563 2.042,0.208 10 false Blind Spot Monitor Sensor LH*2 0.24,3.708 1.688,4.115 1.448,0.406 10 false Television Camera Assembly*3, *6 5.427,7.219 7.156,7.729 1.729,0.51 10 false Central Gateway ECU (Network Gateway ECU) 5.635,5.438 7.125,5.813 1.49,0.375 10 false Clearance Warning ECU Assembly*4 5.563,4 7.115,4.24 1.552,0.24 10 false Parking Assist ECU*3 5.625,2.448 7,2.813 1.375,0.365 10 false Millimeter Wave Radar Sensor Assembly*1 5.615,0.969 6.875,1.333 1.26,0.365 10 false Forward Recognition Camera*1 2.323,3.792 3.531,4.219 1.208,0.427 10 false No. 8 CAN Junction Connector 3.552,7.167 4.771,7.615 1.219,0.448 10 false No. 2 CAN Junction Connector 0.229,0.844 1.781,1.083 1.552,0.24 10 false N54 0.688,0.24 2.24,0.479 1.552,0.24 10 false CANH 0.708,0.646 2.26,0.885 1.552,0.24 10 false CANL 0.865,1.646 1.323,1.844 0.458,0.198 10 false CA1P 0.865,2.042 1.313,2.26 0.448,0.219 10 false CA1N 0.844,3 2.396,3.24 1.552,0.24 10 false CANH 0.865,3.396 2.417,3.635 1.552,0.24 10 false CANL 5.948,0.24 6.531,0.469 0.583,0.229 10 false CA1P 5.948,0.635 6.531,0.865 0.583,0.229 10 false CA1N 5.927,1.729 6.51,1.958 0.583,0.229 10 false CA2H 5.927,2.104 6.51,2.333 0.583,0.229 10 false CA2L 5.927,3.281 6.51,3.51 0.583,0.229 10 false CANH 5.927,3.688 6.51,3.917 0.583,0.229 10 false CANL 5.938,4.698 6.521,4.927 0.583,0.229 10 false R1 5.948,5.073 6.531,5.302 0.583,0.229 10 false R2 6,6.354 6.583,6.583 0.583,0.229 10 false CA1H 6,6.969 6.583,7.198 0.583,0.229 10 false CA1L 0.24,2.188 1.792,2.427 1.552,0.24 10 false Q1 0.24,3.542 1.792,3.781 1.552,0.24 10 false R15 5.563,3.833 7.156,4.042 1.594,0.208 10 false N25 5.625,2.271 7.146,2.479 1.521,0.208 10 false B9 5.615,0.802 7.156,1.01 1.542,0.208 10 false P8 1.354,0.125 2.948,0.333 1.594,0.208 10 false 3 5.552,7.01 7.146,7.219 1.594,0.208 10 false G72 3.542,6.979 5.135,7.188 1.594,0.208 10 false G102 2.323,3.615 3.917,3.823 1.594,0.208 10 false N53 1.354,0.542 2.948,0.75 1.594,0.208 10 false 2 1.365,1.563 1.521,1.823 0.156,0.26 10 false 2 1.375,1.948 1.521,2.146 0.146,0.198 10 false 7 1.365,2.885 1.552,3.094 0.188,0.208 10 false 4 1.365,3.292 1.521,3.542 0.156,0.25 10 false 1 2.563,2.885 2.75,3.083 0.188,0.198 10 false 3 2.563,3.302 2.823,3.5 0.26,0.198 10 false 9 2.563,1.927 4.156,2.135 1.594,0.208 10 false 8 2.563,1.542 4.156,1.75 1.594,0.208 10 false 2 2.5,0.542 4.094,0.75 1.594,0.208 10 false 10 2.552,0.135 4.146,0.344 1.594,0.208 10 false 4 3.292,0.135 4.885,0.344 1.594,0.208 10 false 1 3.313,0.542 4.906,0.75 1.594,0.208 10 false 7 3.771,0.552 5.365,0.76 1.594,0.208 10 false 13 3.823,0.156 5.417,0.365 1.594,0.208 10 false 3 4.573,0.135 6.167,0.344 1.594,0.208 10 false 6 4.563,0.552 6.156,0.76 1.594,0.208 10 false 16 4.573,1.625 6.167,1.833 1.594,0.208 10 false 2 5.74,0.156 7.146,0.365 1.406,0.208 10 false 5 5.677,0.542 7.104,0.75 1.427,0.208 10 false 11 5.729,1.625 7.156,1.833 1.427,0.208 10 false 3 5.729,2 7.156,2.208 1.427,0.208 10 false 2 5.667,3.573 7.094,3.781 1.427,0.208 10 false 12 5.667,3.156 7.094,3.365 1.427,0.208 10 false 11 5.688,4.583 7.115,4.792 1.427,0.208 10 false 17 5.677,4.979 7.104,5.188 1.427,0.208 10 false 18 5.688,6.354 7.115,6.563 1.427,0.208 10 false 23 5.729,6.771 7.156,6.979 1.427,0.208 10 false 8 4.542,6.771 5.969,6.979 1.427,0.208 10 false 18 4.563,6.333 5.99,6.542 1.427,0.208 10 false 8 4.563,5 5.99,5.208 1.427,0.208 10 false 17 4.573,4.573 6,4.781 1.427,0.208 10 false 7 4.563,3.542 5.99,3.75 1.427,0.208 10 false 15 4.583,3.167 6.01,3.375 1.427,0.208 10 false 5 4.583,2.021 6.01,2.229 1.427,0.208 10 false 12 5.646,5.26 7.156,5.49 1.51,0.229 10 false H4 0.083,7.781 2.125,7.99 2.042,0.208 10 false *1: w/ Pre-collision System 0.083,8.125 2.333,8.385 2.25,0.26 10 false *2: w/ Blind Spot Monitor System 0.083,8.469 2.625,8.771 2.542,0.302 10 false *3: w/ Panoramic View Monitor System 2.667,7.813 5.552,8.115 2.885,0.302 10 false *4: w/ TOYOTA Parking Assist-sensor System 2.667,8.156 5.625,8.385 2.958,0.229 10 false *5: w/ Grille Shutter System 0.229,5.333 2.688,5.552 2.458,0.219 10 false Swing Grille Actuator Assembly*5 1.448,6.604 1.865,6.802 0.417,0.198 10 false A 0.896,4.688 1.354,4.885 0.458,0.198 10 false CANP 0.875,5.094 1.333,5.292 0.458,0.198 10 false CANN 3.813,4.594 4,4.802 0.188,0.208 10 false 4 3.771,5 4.052,5.198 0.281,0.198 10 false 14 1.354,5 1.708,5.24 0.354,0.24 10 false 5 1.354,4.594 1.729,4.802 0.375,0.208 10 false 6 2.667,8.479 5.021,8.74 2.354,0.26 10 false *6: w/ Parking Assist Monitor System 1.448,6.198 1.865,6.396 0.417,0.198 10 false A 0.229,5.177 0.646,5.375 0.417,0.198 10 false A85 2.01,6.583 2.427,6.781 0.417,0.198 10 false A50 2,6.188 2.417,6.385 0.417,0.198 10 false A50 1.448,6.01 1.854,6.229 0.406,0.219 10 false 6 2.094,5.99 2.615,6.198 0.521,0.208 10 false 2 2.094,6.417 2.438,6.625 0.344,0.208 10 false 3 1.448,6.406 1.75,6.646 0.302,0.24 10 false 5 5.208,8.177 7.156,8.531 1.948,0.354 10 false *7: w/o Canister Pump Module 5.208,8.49 7.156,8.771 1.948,0.281 10 false *8: w/ Canister Pump Module 1.427,6.854 2.76,7.208 1.333,0.354 10 false Radiator Shutter Sub-assembly*5 0.896,6.188 1.354,6.385 0.458,0.198 10 false CANP 0.896,6.594 1.354,6.792 0.458,0.198 10 false CANN 0.198,6.833 1,7.365 0.802,0.531 10 false Swing Grille Actuator Assembly*5 2.333,4.594 2.708,4.802 0.375,0.208 10 false *7 2.333,4.979 2.708,5.188 0.375,0.208 10 false *7 2.917,6.104 3.292,6.313 0.375,0.208 10 false *8 2.927,6.51 3.302,6.719 0.375,0.208 10 false *8


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 2 CAN junction connector.

C387411C37
0.313,1.219 0.75,1.5 0.438,0.281 1.417,0.76 1.583,0.76 1.583,0.76 2.229,1.396 true 1.396,2.135 1.563,2.135 1.563,2.135 2.24,1.667 true 1.719,0.583 1.885,0.583 1.885,0.583 2.635,1.427 true 1.521,2.323 1.688,2.323 1.688,2.323 2.615,1.656 true 1.948,0.406 2.115,0.406 2.115,0.406 2.99,1.365 true 1.75,2.5 1.917,2.5 1.917,2.5 2.979,1.625 true 2,0.198 2.167,0.198 2.167,0.198 3.354,1.396 true 2.083,2.667 2.25,2.667 2.25,2.667 3.365,1.625 true 4.604,0.208 4.354,0.208 4.354,0.208 3.75,1.385 true 4.51,2.635 4.26,2.635 4.26,2.635 3.76,1.615 true 4.823,0.396 4.573,0.396 4.573,0.396 4.125,1.417 true 4.792,2.396 4.542,2.396 4.542,2.396 4.146,1.594 true 5.115,0.656 4.865,0.656 4.865,0.656 4.51,1.417 true 5.031,2.094 4.781,2.094 4.781,2.094 4.5,1.604 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,1.281 0.781,1.49 0.406,0.208 10 false G102 0.844,2.052 1.427,2.26 0.583,0.208 10 false CANL*b 0.875,0.698 1.458,0.906 0.583,0.208 10 false CANH*b 1.031,2.26 1.615,2.469 0.583,0.208 10 false CANL*c 1.167,0.521 1.75,0.729 0.583,0.208 10 false CANH*c 1.198,2.427 1.781,2.635 0.583,0.208 10 false CANL*d 1.365,0.323 1.948,0.531 0.583,0.208 10 false CANH*d 1.583,2.604 2.26,2.792 0.677,0.188 10 false CANL*e 1.438,0.104 2.021,0.313 0.583,0.208 10 false CANH*e 4.573,2.583 5.156,2.792 0.583,0.208 10 false CANL*f 4.688,0.135 5.271,0.313 0.583,0.177 10 false CANH*f 4.875,2.344 5.458,2.552 0.583,0.208 10 false CANL*g 4.906,0.344 5.49,0.521 0.583,0.177 10 false CANH*g 5.104,2.042 5.688,2.25 0.583,0.208 10 false CANL*h 5.198,0.583 5.781,0.76 0.583,0.177 10 false CANH*h
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Millimeter Wave Radar Sensor Assembly (w/ Pre-collision System)
*c to No. 8 CAN Junction Connector *d to Swing Grille Actuator Assembly (w/ Grille Shutter System)
*e to Parking Assist ECU (w/ Panoramic View Monitor System) *f to Forward Recognition Camera (w/ Pre-collision System)
*g to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) *h to Central Gateway ECU (Network Gateway ECU)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Pre-collision System

*2: w/ TOYOTA Parking Assist-sensor System

*3: w/ Panoramic View Monitor System

*4: w/ Grille Shutter System

G102-2 (CANH) - G102-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*1
G102-3 (CANH) - G102-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 8 CAN junction connector
G102-4 (CANH) - G102-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Swing grille actuator assembly*4
G102-5 (CANH) - G102-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Parking assist ECU*3
G102-6 (CANH) - G102-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward recognition camera*1
G102-7 (CANH) - G102-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance warning ECU assembly*2
G102-8 (CANH) - G102-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 8 CAN junction connector CAN main wire) C
NG (Swing grille actuator assembly CAN branch wire)(w/ Canister Pump Module) D
NG (Wire to ECU or sensor) E



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)

D

6.CHECK FOR SHORT IN CAN BUS WIRES (SWING GRILLE ACTUATOR ASSEMBLY BRANCH WIRE)

E

5.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
2.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the G102 No. 2 CAN junction connector.


b.
C368242C39
1.417,0.24 1.958,0.458 0.542,0.219 2.427,1.302 2.26,1.854 2.26,1.854 2.427,1.854 true 2.344,1.094 2.448,0.677 2.448,0.677 2.615,0.677 true 1.563,0.281 2.021,0.479 0.458,0.198 10 false G72 2.677,0.625 3.135,0.823 0.458,0.198 10 false CA1L 2.49,1.792 2.948,1.99 0.458,0.198 10 false CA1H 0.073,0.042 0.531,0.24 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-23 (CA1H) - G72-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)

3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
a.

Reconnect the G102 No. 2 CAN junction connector.


b.

Disconnect the No. 8 CAN junction connector.

C387413C61
0.365,1.271 0.771,1.5 0.406,0.229 1.833,1.135 2,1.135 2,1.135 2.448,1.333 true 1.865,1.729 2.031,1.729 2.031,1.729 2.417,1.563 true 1.938,0.656 2.104,0.656 2.104,0.656 2.885,1.344 true 2.01,2.052 2.177,2.052 2.177,2.052 2.906,1.563 true 2.167,0.375 2.333,0.375 2.333,0.375 3.313,1.302 true 2.219,2.417 2.385,2.417 2.385,2.417 3.313,1.573 true 4.917,0.26 4.667,0.26 4.667,0.26 3.792,1.323 true 4.615,2.438 4.365,2.438 4.365,2.438 3.833,1.615 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.427,1.323 0.792,1.479 0.365,0.156 10 false N53 1.313,1.073 1.865,1.25 0.552,0.177 10 false CANH*b 1.354,1.667 1.906,1.844 0.552,0.177 10 false CANL*b 1.417,0.594 1.969,0.771 0.552,0.177 10 false CANH*c 1.469,1.979 2.021,2.156 0.552,0.177 10 false CANL*c 1.646,0.313 2.198,0.49 0.552,0.177 10 false CANH*d 1.719,2.354 2.271,2.531 0.552,0.177 10 false CANL*d 4.99,0.208 5.542,0.385 0.552,0.177 10 false CANH*e 4.677,2.385 5.229,2.563 0.552,0.177 10 false CANL*e
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) *d to Television Camera Assembly (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System)
*e to No. 1 CAN Junction Terminal - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Blind Spot Monitor System

*2: w/ Panoramic View Monitor System

*3: w/ Parking Assist Monitor System

N53-1 (CANH) - N53-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 2 CAN junction connector
N53-2 (CANH) - N53-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH*1
N53-3 (CANH) - N53-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Television camera assembly*2, *3
N53-4 (CANH) - N53-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction terminal



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction terminal CAN main wire) B
NG (No. 2 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)
a.

Reconnect the N53 No. 8 CAN junction connector.


b.
C369111C26
1.5,0.333 1.917,0.583 0.417,0.25 1.729,1.135 1.563,0.667 1.563,0.667 1.417,0.667 true 1.948,1.146 2.073,0.667 2.073,0.667 2.24,0.667 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.594,0.375 2.104,0.615 0.51,0.24 10 false N54 2.281,0.604 2.771,0.865 0.49,0.26 10 false CANH 0.99,0.594 1.479,0.854 0.49,0.26 10 false CANL
*a Front view of wire harness connector
(to No. 1 CAN Junction Terminal)


Disconnect the No. 1 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N54-3 (CANH) - N54-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR)

5.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>TERMINALS OF ECU


c.
C368243C43
1.448,0.104 1.917,0.323 0.469,0.219 1,0.417 1.167,0.417 1.167,0.417 1.24,0.979 true 0.938,1.76 1.104,1.76 1.104,1.76 1.177,1.104 true 0.563,1.698 1.021,1.896 0.458,0.198 10 false CA1H 1.563,0.135 2.021,0.333 0.458,0.198 10 false G72 0.635,0.365 1.094,0.563 0.458,0.198 10 false CA1L 0.063,0.063 0.521,0.26 0.458,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-23 (CA1H) - G72-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK FOR SHORT IN CAN BUS WIRES (SWING GRILLE ACTUATOR ASSEMBLY BRANCH WIRE)
a.

Reconnect the G102 No. 2 CAN junction connector.


b.
C378928C47
1.5,0.125 1.927,0.385 0.427,0.26 2.281,1.885 2.115,1.885 2.115,1.885 2.115,1.219 true 1.781,1.885 1.948,1.885 1.948,1.885 1.948,1.219 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 1.677,0.177 2.083,0.385 0.406,0.208 10 false A 2.365,1.823 2.885,2.031 0.521,0.208 10 false CANP 1.292,1.823 1.813,2.031 0.521,0.208 10 false CANN
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Disconnect the swing grille actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-6 (CANP) - A-5 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NG

7.CHECK FOR SHORT IN CAN BUS WIRES (RADIATOR SHUTTER SUB-ASSEMBLY BRANCH WIRE)
7.CHECK FOR SHORT IN CAN BUS WIRES (RADIATOR SHUTTER SUB-ASSEMBLY BRANCH WIRE)
a.

Reconnect the swing grille actuator assembly connector.


b.
C405911C02
1.5,0.25 1.917,0.5 0.417,0.25 1.063,1.531 1.229,1.531 1.229,1.531 1.531,1.177 true 1.875,0.917 2.281,0.583 2.281,0.583 2.448,0.583 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.573,0.292 1.885,0.49 0.313,0.198 10 false A50 0.615,1.448 1.083,1.646 0.469,0.198 10 false CANN 2.5,0.51 2.969,0.708 0.469,0.198 10 false CANP
*a Front view of wire harness connector
(to Radiator Shutter Sub-assembly)


Disconnect the radiator shutter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-2 (CANP) - A50-3 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIATOR SHUTTER SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (RADIATOR SHUTTER SUB-ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)