The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the network gateway ECU removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION (for Manual Transaxle)
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
58810J
6.REMOVE CONSOLE BOX ASSEMBLY
67913B
7.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62111C
8.REMOVE COWL SIDE TRIM BOARD RH
55607
9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55550
10.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
55433B
11.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
82877
12.REMOVE ECU INTEGRATION BOX RH (except Manual Transaxle)
w/ Clearance Warning System:
Disconnect the connector.
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and relay holder.
| *A | Relay holder reverse side | - | - |
|
Protective Tape | - | - |
Disconnect the 4 connectors.
Detach the 3 wire harness clamps.
|
Nut |
|
Bolt |
Remove the nut, bolt and ECU integration box RH.
13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Manual Transaxle)
82877
14.REMOVE ECU INTEGRATION BOX RH (for Manual Transaxle)
| *a | w/ Clearance Warning System |
Detach the wire harness clamp.
w/ Clearance Warning System:
Disconnect the 5 connectors.
w/o Clearance Warning System:
Disconnect the 4 connectors.
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and wire harness protector and remove ECU integration box RH.
| *A | Harness protector reverse side | - | - |
|
Protective Tape | - | - |
89111
15.REMOVE NETWORK GATEWAY ECU
|
Remove in this Direction |
Detach the claw and remove the network gateway ECU.