This DTC is stored when a microphone signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1572 | Microphone Error | Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON. | ·
Telephone transceiver assembly ·
Telephone microphone assembly ·
Map light assembly ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the H6 telephone transceiver assembly connector.
Disconnect the P14 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-33 (MCVD) - P14-7 (MACC) | Always | Below 1 Ω |
| H6-34 (MCI+) - P14-6 (MCO+) | Always | Below 1 Ω |
| H6-35 (MCI-) - P14-5 (MCO-) | Always | Below 1 Ω |
| H6-33 (MCVD) or P14-7 (MACC) - Body ground | Always | 10 kΩ or higher |
| H6-34 (MCI+) or P14-6 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H6-35 (MCI-) or P14-5 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H6-32 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P14-7 (MACC) - A-5 (MACC) | Always | Below 1 Ω |
| P14-6 (MCO+) - A-3 (MIC+) | Always | Below 1 Ω |
| P14-5 (MCO-) - A-2 (MIC-) | Always | Below 1 Ω |
| P14-7 (MACC) - P14-6 (MCO+) | Always | 10 kΩ or higher |
| P14-7 (MACC) - P14-5 (MCO-) | Always | 10 kΩ or higher |
| P14-6 (MCO+) - P14-5 (MCO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT