Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for ERA-GLONASS) › from 2019.09
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0389152 TELEMATICS SYSTEM(for ERA-GLONASS) C

TELEMATICS  TELEMATICS SYSTEM(for ERA-GLONASS)  B1583  GPS Signal Unreceived  


DESCRIPTION

This DTC is stored when GNSS satellite signals is not received for 30 km/h (19 mph).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1583 GPS Signal Unreceived GNSS signals are not received for 30 km.
·

Telephone transceiver assembly

·

No. 1 amplifier antenna assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna divider



WIRING DIAGRAM

E385666E05
5.688,6.594 6.844,7.458 1.156,0.865 10 false No. 1 Amplifier Antenna Assembly 3.906,1.75 5.281,2.792 1.375,1.042 10 false Telephone Transceiver Assembly 2.25,1.563 3.531,2.542 1.281,0.979 10 false No. 2 Antenna Cord Sub-assembly 0.552,6.573 1.74,7.563 1.188,0.99 10 false Antenna Cord Sub-assembly 2.323,6.563 3.615,7.677 1.292,1.115 10 false No. 3 Antenna Cord Sub-assembly 4.01,6.583 5.229,7.448 1.219,0.865 10 false No. 4 Antenna Cord Sub-assembly 5.385,6.198 6.573,7.188 1.188,0.99 10 false A 5.375,5.604 6.563,6.594 1.188,0.99 10 false A 1.958,5.615 3.146,6.604 1.188,0.99 10 false C 1.969,6.198 3.156,7.188 1.188,0.99 10 false C 3.667,0.771 4.854,1.76 1.188,0.99 10 false G 3.656,1.01 4.844,2 1.188,0.99 10 false 1a 3.677,0.552 4.865,1.542 1.188,0.99 10 false 1 3.677,5.625 4.865,6.521 1.188,0.896 10 false B 3.688,6.208 4.875,7.198 1.188,0.99 10 false B 3.688,1.219 4.875,2.208 1.188,0.99 10 false G 2.333,4.563 3.51,5.615 1.177,1.052 10 false Antenna Divider 1.958,3.771 3.177,5.198 1.219,1.427 10 false D 1.969,4.229 3.188,5.656 1.219,1.427 10 false D 1.969,3.313 3.188,4.74 1.219,1.427 10 false D 1.958,2.885 3.177,4.313 1.219,1.427 10 false D 1.969,1.219 3.156,2.208 1.188,0.99 10 false E 1.958,0.771 3.146,1.76 1.188,0.99 10 false E 5.385,5.417 6.573,6.406 1.188,0.99 10 false 5 5.354,5.99 6.542,6.979 1.188,0.99 10 false 5a 3.635,6 4.823,6.99 1.188,0.99 10 false 1a 3.677,5.406 4.865,6.396 1.188,0.99 10 false 1 1.938,5.979 2.188,6.156 0.25,0.177 10 false 5a 1.979,5.406 2.115,5.583 0.135,0.177 10 false 5 1.969,2.677 3.156,3.667 1.188,0.99 10 false 5 1.938,3.125 3.125,4.115 1.188,0.99 10 false 5a 1.948,3.583 3.135,4.573 1.188,0.99 10 false 6 1.927,4.031 3.115,5.021 1.188,0.99 10 false 6a 1.927,1 3.115,1.99 1.188,0.99 10 false 1a 1.969,0.563 3.156,1.552 1.188,0.99 10 false 1 4.021,0.771 5.458,1.531 1.438,0.76 10 false ANT2

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.MOVE VEHICLE
a.

If the vehicle is outside the communication service area, move the vehicle into a communication service area, wait for a while and perform the operation again.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK OPTIONAL COMPONENTS
3.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result:
Result Proceed to
Optional components are not installed A
Optional components are installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

4.CHECK DTC OUTPUT

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233

Result:
Result Proceed to
No DTCs are output. A
DTC B1583 is output. B



A

END

B

5.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
5.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E389828C05
1.479,0.302 1.917,0.521 0.438,0.219 1.469,2.729 1.906,2.948 0.438,0.219 2.167,4.198 2.292,4.198 2.292,4.198 2.458,3.646 true 2.365,0.99 2.26,0.99 2.26,0.99 1.833,1.354 true 2.417,0.896 2.875,1.271 0.458,0.375 10 false 5a 1.958,4.115 2.271,4.313 0.313,0.198 10 false 1a 1.646,0.344 1.958,0.542 0.313,0.198 10 false A 1.635,2.771 1.948,2.969 0.313,0.198 10 false B 0.333,0.281 0.646,0.479 0.313,0.198 10 false *a 0.323,2.625 0.635,2.823 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the No. 4 antenna cord sub-assembly from the No. 1 amplifier antenna assembly connector.


b.

Disconnect the No. 4 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-5 - B-1 Always Below 1 Ω
A-5a - B-1a Always Below 1 Ω
A-5 or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

6.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E383188C02
1.469,2.365 1.875,2.604 0.406,0.24 1.469,0.427 1.875,0.667 0.406,0.24 2.094,3.354 2.417,3.958 2.417,3.958 2.542,3.958 true 0.875,1.49 1.198,2.073 1.198,2.073 1.323,2.073 true 1.625,0.469 2,0.708 0.375,0.24 10 false B 1.625,2.406 2,2.646 0.375,0.24 10 false C 1.375,2 1.75,2.24 0.375,0.24 10 false 1a 2.583,3.885 2.958,4.125 0.375,0.24 10 false 5a 0.323,0.26 0.698,0.5 0.375,0.24 10 false *a 0.292,2.26 0.667,2.5 0.375,0.24 10 false *b
*a Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the No. 3 antenna cord sub-assembly from the No. 4 antenna cord sub-assembly connector.


b.

Disconnect the No. 3 antenna cord sub-assembly from the antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - C-5 Always Below 1 Ω
B-1a - C-5a Always Below 1 Ω
B-1 or C-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

7.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E405967C01
1.552,1.75 1.958,1.99 0.406,0.24 1.531,0.271 1.938,0.51 0.406,0.24 1.573,3.177 1.979,3.417 0.406,0.24 1.198,3.979 1.469,4.406 1.469,4.406 1.594,4.406 true 2.479,2.448 2.729,2.063 2.729,2.063 2.854,2.063 true 2.146,2.563 2.365,3.021 2.365,3.021 2.49,3.021 true 1.344,1.104 1.094,1.552 1.094,1.552 0.938,1.552 true 1.677,0.323 2.052,0.563 0.375,0.24 10 false C 2.906,1.979 3.281,2.219 0.375,0.24 10 false 6a 1.656,4.323 2.031,4.563 0.375,0.24 10 false 1a 1.698,1.792 2.073,2.031 0.375,0.24 10 false D 1.719,3.219 2.094,3.458 0.375,0.24 10 false E 2.552,2.938 2.927,3.177 0.375,0.24 10 false 5a 0.75,1.458 1.125,1.698 0.375,0.24 10 false 5a 0.302,0.167 0.677,0.406 0.375,0.24 10 false *a 0.302,1.792 0.677,2.031 0.375,0.24 10 false *b 0.365,3.135 0.74,3.375 0.375,0.24 10 false *c
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Divider)
*c Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


b.

Disconnect the antenna cord sub-assembly from the antenna divider connector.


c.

Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-5 - D-6 Always Below 1 Ω
C-5a - D-6a Always Below 1 Ω
D-6 - E-1 Always Below 1 Ω
D-6a - E-1a Always Below 1 Ω
C-5 or D-6 - Body ground Always 10 kΩ or higher
D-6 or E-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

8.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E405966C01
1.573,2.323 2.01,2.583 0.438,0.26 1.583,0.417 2.021,0.677 0.438,0.26 2.521,1.49 2.646,2.083 2.646,2.083 2.781,2.083 true 1.99,3.542 2.406,3.156 2.406,3.156 2.542,3.156 true 1.76,3.583 1.281,3.115 1.281,3.115 1.083,3.115 true 1.75,0.458 1.906,0.656 0.156,0.198 10 false E 1.74,2.385 1.938,2.583 0.198,0.198 10 false G 2.844,2 3.115,2.25 0.271,0.25 10 false 1a 2.594,3.083 2.865,3.333 0.271,0.25 10 false 1a 0.354,0.229 0.667,0.385 0.313,0.156 10 false *a 0.427,2.302 0.74,2.458 0.313,0.156 10 false *b 0.708,3.031 1.385,3.396 0.677,0.365 10 false ANT2
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.


b.

Disconnect the No. 2 antenna cord sub-assembly from the telephone transceiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 - G-1(ANT2) Always Below 1 Ω
E-1a - G-1a Always Below 1 Ω
E-1 or G-1(ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT ANTENNA DIVIDER

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

9.INSPECT ANTENNA DIVIDER
a.
E241596C20
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.406,1.427 1.49,1.771 1.49,1.771 1.74,1.771 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.813,1.688 2.24,1.865 0.427,0.177 10 false 5a 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Remove the antenna divider.

Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 - 6 Always Below 1 Ω
5a - 6a Always Below 1 Ω
5 - 5a Always 10 kΩ or higher
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

10.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT