These DTCs are stored when a malfunction occurs in the telephone antenna.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | Short in GPS Antenna | Current to the No. 1 amplifier antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Short circuit) |
·
Telephone transceiver assembly ·
No. 1 amplifier antenna assembly ·
No. 4 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Antenna divider |
| B15C1 | Open in GPS Antenna | Current for No. 1 amplifier antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Open circuit) |
·
Telephone transceiver assembly ·
No. 1 amplifier antenna assembly ·
No. 4 antenna cord sub-assembly ·
No. 3 antenna cord sub-assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Antenna divider |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly) |
| *b | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Disconnect the No. 4 antenna cord sub-assembly from the No. 1 amplifier antenna assembly connector.
Disconnect the No. 4 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-5 - B-1 | Always | Below 1 Ω |
| A-5a - B-1a | Always | Below 1 Ω |
| A-5 or B-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the No. 3 antenna cord sub-assembly from the No. 4 antenna cord sub-assembly connector.
Disconnect the No. 3 antenna cord sub-assembly from the antenna cord sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - C-5 | Always | Below 1 Ω |
| B-1a - C-5a | Always | Below 1 Ω |
| B-1 or C-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Divider) |
| *c | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.
Disconnect the antenna cord sub-assembly from the antenna divider connector.
Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-5 - D-6 | Always | Below 1 Ω |
| C-5a - D-6a | Always | Below 1 Ω |
| D-6 - E-1 | Always | Below 1 Ω |
| D-6a - E-1a | Always | Below 1 Ω |
| C-5 or D-6 - Body ground | Always | 10 kΩ or higher |
| D-6 or E-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.
Disconnect the No. 2 antenna cord sub-assembly from the telephone transceiver assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 - G-1(ANT2) | Always | Below 1 Ω |
| E-1a - G-1a | Always | Below 1 Ω |
| E-1 or G-1(ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Antenna Divider) |
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - 6 | Always | Below 1 Ω |
| 5a - 6a | Always | Below 1 Ω |
| 5 - 5a | Always | 10 kΩ or higher |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 amplifier antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT