Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2019.09
RM3620E _51 Engine / Hybrid System _076382 A25A-FKS ENGINE CONTROL _0376982 SFI SYSTEM(w/o Canister Pump Module) J

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).

*1: w/o Entry and Start System

*2: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH STOP AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B




A

2.CHECK WHETHER ENGINE CAN BE CRANKED

B

6.CHECK WHETHER ENGINE CAN BE CRANKED
2.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

3.READ VALUE USING GTS (STARTER SW)

B

5.READ VALUE USING GTS (STARTER SW)
3.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

GO TO STOP AND START SYSTEM

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 2 RELAY)
4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-23 (STA2) - A24-30 (STA) Always Below 1 Ω
A34-23 (STA2), A24-30 (STA) or 2 (ST NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO STOP AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 2 RELAY - ECM)

6.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

7.READ VALUE USING GTS (STARTER SW)

B

21.READ VALUE USING GTS (STARTER SW)
7.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

8.INSPECT ST NO. 1 RELAY

NG

15.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
8.INSPECT ST NO. 1 RELAY
a.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>A25A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

9.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - C42-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay) or C42-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - D2-1 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A435792C02
0.094,0.063 0.406,0.219 0.313,0.156 10 false *1 2.125,1.188 2.438,1.344 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY)

13.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - C31-9 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

16.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

18.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

16.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-20 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
C31-9 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A24-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A15-20 (STA), 2 (ST NO. 1 relay), C31-9 (L) or A24-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - C31-4 (B) Always Below 1 Ω
A15-9 (STAR) - A24-23 (NSW) Always Below 1 Ω
A15-9 (STAR), C31-4 (B) or A24-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C31-9 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A24-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
C31-9 (L), 2 (ST NO. 1 relay) or A24-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-5 (ST1) - C31-4 (B) Always Below 1 Ω
G28-5 (ST1) - A24-23 (NSW) Always Below 1 Ω
G28-5 (ST1), C31-4 (B) or A24-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>A25A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

21.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)