When the roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) detects a motor malfunction and the sliding roof operation is stopped, DTC B2347 is stored.
When the roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2349 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2347 | Sensor (Motor) Failure (Fr Shade) | Sensor (motor) failure (When the roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) enters fail-safe mode due to a problem with the motor) | ·
Roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) ·
Map light sub-assembly ·
Harness or connector |
| B2349 | Position Failure (Fr Shade) | Position failure (When the roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) enters fail-safe mode due to a problem with the gear position) | ·
Roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) ·
Map light sub-assembly ·
Harness or connector |
When the roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) is removed and reinstalled or replaced, the roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) must be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
The panoramic moon roof system uses the CAN and LIN communication system. First, confirm that there are no malfunctions in the CAN and LIN communication system. Refer to How to Proceed with Troubleshooting.
Check the roof sunshade auto operation function.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>OPERATION CHECK
Auto operation function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DTC CHECK / CLEAR
DTCs B2347 and B2349 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
Check that the roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) can be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
Roof sunshade ECU (sliding roof drive gear assembly [roof sunshade]) can be initialized.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DTC CHECK / CLEAR
DTCs B2347 and B2349 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
Perform the Active Test according to the display on the GTS.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Sliding Sunshade | Operate sunshade motor | OFF / Opn/Dwn / Clos/Up | - |
| Tester Display |
|---|
| Front Sliding Sunshade |
Roof sunshade is operated using the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
Using the GTS, read the Data List.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shade Close Switch | Sunshade close switch signal | ON or OFF | OFF: Roof sunshade switch (close) not pressed
ON: Roof sunshade switch (open) pressed |
- |
| Shade Open Switch | Roof sunshade open switch signal | ON or OFF | OFF: Roof sunshade switch (open) not pressed
ON: Roof sunshade (open) switch pressed |
- |
| Tester Display |
|---|
| Shade Close Switch |
| Shade Open Switch |
The GTS display changes according to switch operation as shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
NG
Remove the map light sub-assembly.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL
Inspect the map light sub-assembly.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the P20 map light sub-assembly connector.
Disconnect the P4 sliding roof ECU (sliding roof drive gear assembly [sliding roof]) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P4-9 (DWN) - P20-18 (DOWN) | Always | Below 1 Ω |
| P4-5 (UP) - P20-19 (UP) | Always | Below 1 Ω |
| P4-2 (E) - Body ground | Always | Below 1 Ω |
| P20-13 (GND) - Body ground | Always | Below 1 Ω |
| P4-9 (DWN) or P20-18 (DOWN) - Body ground | Always | 10 kΩ or higher |
| P4-5 (UP) or P20-19 (UP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL
NG