Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY) › from 2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425052 HYBRID CONTROL SYSTEM(for 4WD/AWD with LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD with LITHIUM-ION BATTERY)  P1CE213  PCU Interlock Circuit Open  P1CE292  PCU Interlock Performance or Incorrect Operation  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU assembly detects that a safety device (interlock) is operated or that there is an open circuit in the detection circuit. (Even if an open circuit occurs while the vehicle is stopped, the system determines that the safety device was operated.)

The cause of this malfunction may be one of the following:

Detection switch system malfunction
·

Inverter with converter assembly malfunction


Low-voltage system malfunction
·

MG ECU malfunction

·

Inverter with converter assembly malfunction

·

CAN communication error between the MG ECU and hybrid vehicle control ECU assembly



INSPECTION DESCRIPTION


C414429E01
1.313,3.25 1.667,3.458 0.354,0.208 10 false : *b 2.156,1.073 2.51,1.281 0.354,0.208 10 false *a 2.417,3.094 4.531,3.375 2.115,0.281 10 false Inverter with Converter Assembly 5.833,2.563 6.469,2.771 0.635,0.208 10 false MG ECU 4.083,1.583 5.01,1.854 0.927,0.271 10 false Inverter Cover 4.792,1.073 5.146,1.281 0.354,0.208 10 false *a 0.781,1.563 3.865,1.802 3.083,0.24 10 false HV Floor Under Wire (Rear Traction Motor Cable)

System Diagram Location Inspection Content Reason Inspection Step
*a Check whether the safety device (interlock) is connected securely and installed properly (inverter cover, HV floor under wire (rear traction motor cable), etc.). DTC output due to improper connection or forgetting to install parts. 4, 5
*b Inspect the detection circuit. DTC output due to an open circuit or improper connection (dirt, foreign matter, etc.). 6, 7


DESCRIPTION

Refer to the description for DTC P0A0A13.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>P0A0A13

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1CE213 PCU Interlock Circuit Open Interlock signal line opens while the vehicle is being driven (at 5 km/h (3 mph) or more)
(1 trip detection logic)
·

Inverter cover

·

HV Floor under wire (rear traction motor cable)

·

Inverter with converter assembly


Does not come on Master Warning:
Comes on
P1CE292 PCU Interlock Performance or Incorrect Operation Either of the following conditions is met:
·

With the vehicle stopped, the inverter cover with a safety device was removed.

·

With the vehicle stopped, the rear traction motor cable (HV floor under wire) with a safety device was removed.

·

With the vehicle stopped, the interlock signal line became open.


(1 trip detection logic)
·

Inverter cover

·

HV Floor under wire (rear traction motor cable)

·

Inverter with converter assembly


Does not come on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C414430E01
5.875,2.552 6.604,2.802 0.729,0.25 10 false MG ECU 2.521,3.104 4.635,3.333 2.115,0.229 10 false Inverter with Converter Assembly 4.104,1.563 5.073,1.844 0.969,0.281 10 false Inverter Cover 6.167,0.844 6.448,1.083 0.281,0.24 10 false +B 0.823,1.583 3.823,1.813 3,0.229 10 false HV Floor Under Wire (Rear Traction Motor Cable)

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

·

As interlock circuit DTCs or other DTCs may be stored when the power switch is turned on (IG) in the following procedure, make sure to clear the DTCs after inspection.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P1CE213 or P1CE292 only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of motor generator control system in the tables below are output. C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P060B1C Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range
P1CE349 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure
P1CE371 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck
P1CE31C Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
Motor generator control system P0A1B1F Generator Control Module Circuit Intermittent
Power source circuit malfunction Hybrid control system P06881F ECM/PCM Power Relay Sense Circuit Intermittent
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
System malfunction Hybrid control system P1C9E9F Hybrid/EV System Reset Stuck Off

HINT:
·

P1CE213 or P1CE292 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





e.

Turn the power switch off.



A

2.CLEAR DTC

B

C

2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P1CE213 or P1CE292 is output again. A
Neither P1CE213 or P1CE292 is output again. B


HINT:

Check if the same DTC is output.



e.

Turn the power switch off.



A

4.CHECK INVERTER COVER

B

4.CHECK INVERTER COVER
4.CHECK INVERTER COVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C412483

Check if the inverter cover of the inverter with converter assembly is installed correctly.

OK:

The inverter cover is installed correctly.



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR UNDER WIRE (REAR TRACTION MOTOR CABLE CONNECTOR INSTALLATION CONDITION)

NG

INSTALL PARTS CORRECTLY

5.CHECK FLOOR UNDER WIRE (REAR TRACTION MOTOR CABLE CONNECTOR INSTALLATION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C414270

Check if the HV floor under wire (rear traction motor cable) is connected correctly.

OK:

The HV floor under wire (rear traction motor cable) is connected correctly.



Result:
Proceed to
OK
NG



OK

6.CHECK INVERTER COVER

NG

INSTALL PARTS CORRECTLY

6.CHECK INVERTER COVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C412483

Remove the inverter cover from the inverter with converter assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER (for 4WD/AWD)>REMOVAL


c.
A365619C01
0.094,0.083 0.406,0.24 0.313,0.156 10 false *1
*1 Inverter Cover


Check the condition of the inverter cover interlock.

OK:

Dirt or foreign matter has not entered the connectors and there is no evidence of contamination.



d.

Install the inverter cover.


Result:
Proceed to
OK
NG



OK

7.CHECK FLOOR UNDER WIRE (REAR TRACTION MOTOR CABLE CONNECTOR)

NG

7.CHECK FLOOR UNDER WIRE (REAR TRACTION MOTOR CABLE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C414270

Disconnect the HV floor under wire (rear traction motor cable) from the inverter with converter assembly.


c.
C414428C01
0.094,0.083 0.427,0.25 0.333,0.167 10 *1
*1 HV Floor Under Wire (Rear Traction Motor Cable)


Check the condition of HV floor under wire (rear traction motor cable) interlock.

OK:

Dirt or foreign matter has not entered the connectors and there is no evidence of contamination.



d.

Connect the HV floor under wire (rear traction motor cable) to the inverter with converter assembly.


Result:
Proceed to
OK
NG



OK

NG

REPLACE FLOOR UNDER WIRE