Home › Engine / Hybrid System › A25B-FXS (ENGINE MECHANICAL) › ENGINE UNIT › 2020.05–2020.08
RM3620E _51 Engine / Hybrid System _080117 A25B-FXS ENGINE MECHANICAL _0390040 ENGINE UNIT A

A25B-FXS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 17169A 1.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the bolt.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 11452 2.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250E 5.INSTALL DIRECT FUEL INJECTOR ASSEMBLY

Hide 23807 11.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 12.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82126A 13.INSTALL NO. 6 ENGINE WIRE

a.

Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Attach the 2 clamps.


c.

Connect the 4 connectors.


Hide 82219A 14.INSTALL SENSOR WIRE

a.

Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Attach the 3 clamps.


c.

Connect the 4 connectors.


Hide 16295 15.INSTALL NO. 7 WATER BY-PASS HOSE

a.

Install the No. 7 water by-pass hose and slide the 2 clips to secure them.


Hide 23100X 16.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23801P 17.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 18.INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23801P 19.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A407621C02
2.792,2.729 2.833,2.365 2.833,2.365 2.979,2.365 false 3.042,2.292 3.354,2.49 0.313,0.198 10 false *a 1.552,2.354 1.865,2.552 0.313,0.198 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




Hide 17177 21.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 16278 23.INSTALL NO. 2 WATER BY-PASS PIPE

a.
A406696N03
1.813,0.958 1.969,1.156 0.156,0.198 10 true B 1.125,1.604 1.281,1.802 0.156,0.198 10 true B 2.615,1.885 2.771,2.083 0.156,0.198 10 true A

Install the bolt (A).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Using an 8 mm socket wrench, install the No. 2 water by-pass pipe with the 2 bolts (B) in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16279 24.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.


b.

Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25620 25.INSTALL EGR VALVE ASSEMBLY

a.

Using an 8 mm socket wrench, install the EGR valve bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A407182C01
2.313,0.802 2.552,0.448 2.552,0.448 2.677,0.448 true 2.333,0.938 2.552,0.938 true 2.604,0.844 2.917,1.042 0.313,0.198 10 true *a 2.74,0.313 3.052,0.51 0.313,0.198 10 true *b
*a Pin
*b Hole


Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing sub-assembly.


c.

Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Using the 8 mm socket wrench, connect the fuel pipe sub-assembly to the EGR valve bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.


Hide 26.INSTALL WATER HOSE

a.

Connect the water hose to the EGR valve assembly and slide the clip to secure it.


Hide 25601 27.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25680 28.INSTALL EGR COOLER ASSEMBLY

a.

Install the EGR cooler assembly, a new EGR cooler gasket and a new EGR valve gasket with the 5 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


b.

Connect the No. 3 water by-pass hose to the EGR cooler assembly and slide the clip to secure it.


c.

Connect the water hose to the EGR cooler assembly and slide the clip to secure it.


Hide 22030 29.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17167 32.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16260 33.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A409020N01
0.99,0.385 1.146,0.583 0.156,0.198 10 true A 0.948,0.792 1.104,0.99 0.156,0.198 10 true B

Install the water hose clamp bracket with the 2 bolts as shown in the illustration.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts in the order of (B) and (A).



b.
A439779C01
1,3.865 1,3.323 true 0.927,3.885 1.24,4.083 0.313,0.198 10 false *a 2.958,3.625 3.271,3.823 0.313,0.198 10 false *b
*a Paint Mark
*b 90° (Claw of Clip Location)


Connect the flow shutting valve (water by-pass hose assembly) to the water by-pass outlet sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the water by-pass outlet sub-assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




c.

Connect the flow shutting valve (water by-pass hose assembly) with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 16207 34.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 2 water by-pass pipe sub-assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.


Hide 88310 35.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

a.

Using an E8 "TORX" socket wrench, temporarily install the compressor with motor assembly with the 2 stud bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
E371430C03
1.333,1.917 1.49,2.115 0.156,0.198 10 false 1 0.594,1.802 0.75,2 0.156,0.198 10 false 2 0.75,0.167 0.906,0.365 0.156,0.198 10 false 3
V100135

Bolt
V100136

Nut


Install the compressor with motor assembly with the bolt and 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolt and nuts in the order shown in the illustration.



Hide 43457 36.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)