A battery current sensor, which is mounted on the positive cable side of each HV battery junction block assembly, detects the current flowing to or from the battery pack. The battery current sensor sends a voltage, which varies between 0 and 5 V in proportion to the amperage, to the IB0 terminal of the battery ECU assembly. Similarly, it sends a voltage, which varies between 0 and 5 V in inverse proportion to the amperage, to the IB1 terminal of the battery ECU assembly. When the voltage at the IB0 terminal is below 2.8 V and the voltage at the IB1 terminal is above 2.2 V, this indicates that the HV battery is being discharged. Additionally, Meanwhile, when the voltage at of the IB0 terminal is above 2.8 V and the voltage at of the IB1 terminal is below 2.2 V, this indicates that the HV battery is being charged. The battery ECU assembly sends the signals from its IB0 and IB1 terminals to the hybrid vehicle control ECU assembly. The hybrid vehicle control ECU assembly determines the charging and discharging amperage of the HV battery based on the received signals and calculates the SOC of the HV battery using the cumulative amperage value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0ABF00 | Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance | Abnormal battery current sensor characteristics:
(based on hybrid system consumption and HV battery output). (1 trip detection logic) |
·
HV battery junction block assembly ·
Battery ECU assembly ·
No. 1 HV supply stack sub-assembly ·
No. 2 HV supply stack sub-assembly |
Comes on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P0ABF00 | - |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid/EV Battery Current", "Motor Torque" and "Generator Torque".
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.
If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.
| *a | Dealer |
| *b | Battery Collection Agent |
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Before returning the HV battery, make sure to perform a recovery inspection.
Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.
Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.
After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery hose.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU (for LITHIUM-ION BATTERY)>REMOVAL
Disconnect the A No. 1 HV supply stack sub-assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Disconnect the z26 battery ECU assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Front view of wire harness connector
(to Battery ECU Assembly) |
| *b | Front view of wire harness connector
(to No. 2 HV Supply Stack Sub-assembly) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z26-24(IB1) - A-2(IB1) | Power switch off | Below 1 Ω |
| z26-23(GIB) - A-10(GIB) | Power switch off | Below 1 Ω |
| z26-12(IB0) - A-11(IB0) | Power switch off | Below 1 Ω |
| z26-36(VIB) - A-1(VIB) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z26-24(IB1) or A-2(IB1) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z26-23(GIB) or A-10(GIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z26-12(IB0) or A-11(IB0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z26-36(VIB) or A-1(VIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the z26 battery ECU assembly connector.
Reconnect the A No. 1 HV supply stack sub-assembly connector.
Install the No. 1 HV battery hose.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery hose.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU (for LITHIUM-ION BATTERY)>REMOVAL
Disconnect the A No. 2 HV supply stack sub-assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Disconnect the z25 battery current sensor connector from the HV battery junction block assembly.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Front view of wire harness connector
(to No. 1 HV Supply Stack Sub-assembly) |
| *b | Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor)) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2(IB1) - z25-2(IB1) | Power switch off | Below 1 Ω |
| A-10(GIB) - z25-3(GIB) | Power switch off | Below 1 Ω |
| A-11(IB0) - z25-4(IB0) | Power switch off | Below 1 Ω |
| A-1(VIB) - z25-1(VIB) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2(IB1) or z25-2(IB1) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| A-10(GIB) or z25-3(GIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| A-11(IB0) or z25-4(IB0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| A-1(VIB) or z25-1(VIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the z25 battery current sensor connector to the HV battery junction block assembly.
Reconnect the A No. 2 HV supply stack sub-assembly connector.
Install the upper No. 1 HV battery hose.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>REMOVAL
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery hose.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU (for LITHIUM-ION BATTERY)>REMOVAL
Disconnect the z26 battery ECU assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Disconnect the z25 battery current sensor connector from the HV battery junction block assembly.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Front view of wire harness connector
(to Battery ECU Assembly) |
| *b | Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor)) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z26-24(IB1) - z25-2(IB1) | Power switch off | Below 1 Ω |
| z26-23(GIB) - z25-3(GIB) | Power switch off | Below 1 Ω |
| z26-12(IB0) - z25-4(IB0) | Power switch off | Below 1 Ω |
| z26-36(VIB) - z25-1(VIB) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z26-24(IB1) or z25-2(IB1) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z26-23(GIB) or z25-3(GIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z26-12(IB0) or z25-4(IB0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z26-36(VIB) or z25-1(VIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the z25 battery current sensor connector to the HV battery junction block assembly.
Reconnect the z26 battery ECU assembly connector.
Install the No. 1 HV battery hose.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch off.
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid/EV Battery SOC.
| Tester Display |
|---|
| Hybrid/EV Battery SOC |
Check that "Hybrid/EV Battery SOC" shows 60% or less.
If "Hybrid/EV Battery SOC" is 60% or more, reduce it to below 60% by leaving the hybrid system on with shift lever in N.
Apply the parking brake and secure the wheels using chocks.
Turn the power switch on (READY).
Move the shift lever to D while depressing the brake pedal with your left foot and repeat the following steps for 1 minute or more.
Depress and release the accelerator pedal in 5-second intervals (2.5 seconds each) continuously.
While depressing the brake pedal with your left foot, depress the accelerator pedal with your right foot.
Release the accelerator pedal.
Turn the power switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0ABF00 is not output. | A |
| P0ABF00 is output again. | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU (for LITHIUM-ION BATTERY)>REMOVAL
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery hose.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU (for LITHIUM-ION BATTERY)>REMOVAL
Disconnect the A No. 1 HV supply stack sub-assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Check the terminals of the male side of the A No. 1 HV supply stack sub-assembly connector.
The terminals are free of foreign matter and not damaged.
| Proceed to |
|---|
| OK |
| NG |
Reconnect the A No. 1 HV supply stack sub-assembly connector.
Install the upper No. 1 HV battery hose.
OK
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>REMOVAL
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>REMOVAL
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery hose.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU (for LITHIUM-ION BATTERY)>REMOVAL
Disconnect the A No. 1 HV supply stack sub-assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Check the terminals of the male side of the A No. 1 HV supply stack sub-assembly connector.
The terminals are free of foreign matter and not damaged.
| Proceed to |
|---|
| OK |
| NG |
Reconnect the A No. 1 HV supply stack sub-assembly connector.
Install the upper No. 1 HV battery hose.
OK
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>REMOVAL
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>REMOVAL