The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery ECU assembly removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The type of battery ECU assembly to be used varies depending on the vehicle model.
| *a | Black Label |
The type of battery ECU assembly can be confirmed by the color of the label.
If the wrong type of battery ECU assembly is installed, the power switch cannot be turned on (READY).
After installing the battery ECU assembly, perform the following to check that the power switch can be turned on (READY).
Turn the power switch on (READY).
Turn the power switch off and wait for 30 seconds or more.
Turn the power switch on (READY) again.
1. WHEN REPLACING BATTERY ECU ASSEMBLY
HV battery learning values are stored in the battery ECU assembly and ECM and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.
Do not replace the battery ECU assembly and ECM at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.
Do not replace the battery ECU assembly or ECM with a used one from another vehicle.
Procedure when replacing both battery ECU assembly and ECM:
Disconnect the cable from the negative (-) auxiliary battery terminal.
Replace either ECU.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (READY) and wait for 5 minutes or more.
Turn the power switch off and disconnect the cable from the negative (-) auxiliary battery terminal.
Replace the other ECU.
Connect the cable to the negative (-) auxiliary battery terminal.
Check that the power switch can be turned on (READY).
If the battery ECU assembly and ECM are replaced at the same time without following the above procedure, replace either of the ECUs with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.
G3834
2.REMOVE SERVICE PLUG GRIP
82111
3.DISCONNECT ENGINE ROOM MAIN WIRE
4.REMOVE CONNECTOR COVER ASSEMBLY
5.CHECK TERMINAL VOLTAGE
6.INSTALL CONNECTOR COVER ASSEMBLY
82111
7.CONNECT ENGINE ROOM MAIN WIRE
8.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
9.REMOVE REAR SEAT CUSHION LOCK HOOK
899A0
10.REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY
67918E
11.REMOVE REAR DOOR SCUFF PLATE LH
58467H
12.REMOVE NO. 3 BATTERY SERVICE COVER BOARD
67917C
13.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
58466J
14.REMOVE NO. 2 BATTERY SERVICE COVER BOARD
58464D
15.REMOVE BATTERY SERVICE COVER BOARD
71033
16.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
G92N4A
17.REMOVE NO. 1 HV BATTERY COVER PANEL RH
G9290A
18.REMOVE HYBRID BATTERY HOSE ASSEMBLY
82161
19.DISCONNECT FLOOR WIRE
G92PF
20.REMOVE NO. 4 HV BATTERY PROTECTOR
82161
21.DISCONNECT FLOOR WIRE
G920NB
22.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY
Be sure to wear insulated gloves and protective goggles.
| *a | Bolt |
| *b | Nut |
Remove the 5 bolts, 6 nuts and upper HV battery cover sub-assembly from the HV battery.
G929A
23.REMOVE NO. 1 HV BATTERY HOSE
Be sure to wear insulated gloves and protective goggles.
Remove the 2 clips.
Disengage the 2 claws to remove the No. 1 HV battery hose from the HV battery.
89890A
24.REMOVE BATTERY ECU ASSEMBLY
Be sure to wear insulated gloves and protective goggles.
Disengage the clamp.
Move the lock lever while pushing the lock, and disconnect the 3 battery ECU assembly connectors.
| *a | Lever Lock |
Make sure to release the lock of the lock lever before moving it.
If the connector cannot be disconnected, check if the lock lever is completely unlocked.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
Remove the 3 nuts and battery ECU assembly from the HV battery.
If the battery ECU assembly has been struck or dropped, replace it.