Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY) › from 2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425694 HYBRID CONTROL SYSTEM(for 2WD with LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD with LITHIUM-ION BATTERY)  P310715  Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

Refer to the description for DTC P310711.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>P310711

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P310715 Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open Open or short to +B in the communication circuit
Communication from the airbag sensor assembly stopped and Circuit High has been detected for a certain period.
(1 trip detection logic)
·

Wire harness or connector

·

Airbag sensor assembly

·

Hybrid vehicle control ECU assembly


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P310715 Airbag Status (Collision)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 15 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


d.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B



e.

Turn the power switch off.



A

2.CHECK AIR BAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIR BAG SENSOR ASSEMBLY (CHECK WAVEFORM)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>P310711

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B



A

3.CLEAR DTC

B

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P310715 is not output. A
P310715 is output again. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

5.CHECK FOR INTERMITTENT PROBLEMS

OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)
a.
C374925C17
1.292,0.198 1.75,0.438 0.458,0.24 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 1.396,0.229 1.854,0.427 0.458,0.198 10 false G70
*a Component with harness connected
(Airbag Sensor Assembly)


Check the connector connections and contact pressure of the relevant terminals for the G70 airbag sensor assembly connector.

OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - AIRBAG SENSOR ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G70 airbag sensor assembly connector.


c.

Turn the power switch on (IG).


d.
C408033C06
1.375,0.146 1.729,0.375 0.354,0.229 0.969,1.771 0.99,1.292 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *A 0.281,0.396 0.594,0.594 0.313,0.198 10 false *a 1.417,0.177 1.875,0.375 0.458,0.198 10 false A30 0.781,1.802 1.396,2 0.615,0.198 10 false ABFS
*A for LHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


for LHD:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-29 (ABFS) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector and the hybrid vehicle control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.
C408033C07
1.375,0.146 1.729,0.375 0.354,0.229 0.969,1.771 0.99,1.292 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *A 0.281,0.396 0.594,0.594 0.313,0.198 10 false *a 1.417,0.177 1.875,0.375 0.458,0.198 10 false G63 0.781,1.802 1.396,2 0.615,0.198 10 false ABFS
*A for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


for RHD:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G63-29 (ABFS) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector and the hybrid vehicle control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.
C408031C02
1.458,0.146 1.875,0.396 0.417,0.25 1.542,2.229 1.948,2.469 0.406,0.24 1.094,1.885 0.99,1.396 true 1.875,3.479 2,4.24 true 1.531,0.208 2.031,0.438 0.5,0.229 10 false A30 0.938,1.938 1.438,2.167 0.5,0.229 10 false ABFS 0.375,0.26 0.875,0.49 0.5,0.229 10 false *a 1.604,2.281 2.104,2.51 0.5,0.229 10 false G70 1.844,4.281 2.344,4.51 0.5,0.229 10 false GSW2 0.427,2.156 0.927,2.385 0.5,0.229 10 false *b 0.104,0.094 0.417,0.292 0.313,0.198 10 false *A
*A for LHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A30-29 (ABFS) - G70-24 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A30-29 (ABFS) or G70-24 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher



h.
C408031C03
1.458,0.146 1.875,0.396 0.417,0.25 1.51,2.198 1.917,2.438 0.406,0.24 1.094,1.885 0.99,1.396 true 1.885,3.49 2,4.24 true 1.521,0.208 2.021,0.438 0.5,0.229 10 false G63 0.938,1.938 1.438,2.167 0.5,0.229 10 false ABFS 0.375,0.26 0.875,0.49 0.5,0.229 10 false *a 1.583,2.26 2.083,2.49 0.5,0.229 10 false G70 1.844,4.281 2.344,4.51 0.5,0.229 10 false GSW2 0.427,2.208 0.927,2.438 0.5,0.229 10 false *b 0.104,0.094 0.417,0.292 0.313,0.198 10 false *A
*A for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G63-29 (ABFS) - G70-24 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G63-29 (ABFS) or G70-24 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Reconnect the G70 airbag sensor assembly connector.


j.

Reconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

9.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
a.

Disconnect the A30*1, G63*2 airbag sensor assembly connector.

*1: for LHD

*2: for RHD



b.

Turn the power switch on (IG).


c.

for LHD:

Measure the voltage according to the value(s) in the table below.

C407546C45
5.313,0.302 5.656,0.552 0.344,0.25 6.031,1.51 5.854,2.458 true 0.385,0.375 0.698,0.573 0.313,0.198 10 false *a 5.375,0.354 5.833,0.552 0.458,0.198 10 false A30 5.656,2.49 6.156,2.688 0.5,0.198 10 false ABFS 0.125,0.094 0.438,0.292 0.313,0.198 10 false *A
*A for LHD - -
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Standard Voltage:
Tester Connection Condition Specified Condition
A30-29 (ABFS) - Body ground Power switch on (IG) 11 to 14 V



d.

for RHD:

Measure the voltage according to the value(s) in the table below.

C407546C46
5.313,0.302 5.656,0.552 0.344,0.25 6.031,1.51 5.854,2.458 true 0.385,0.375 0.698,0.573 0.313,0.198 10 false *a 5.354,0.354 5.813,0.552 0.458,0.198 10 false G63 5.656,2.49 6.156,2.688 0.5,0.198 10 false ABFS 0.125,0.094 0.438,0.292 0.313,0.198 10 false *A
*A for RHD - -
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Standard Voltage:
Tester Connection Condition Specified Condition
G63-29 (ABFS) - Body ground Power switch on (IG) 11 to 14 V



e.

Turn the power switch off.


f.

Reconnect the A30*1, G63*2 airbag sensor assembly connector.

*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the G70 airbag sensor assembly connector.


b.
C384271C08
0.479,0.938 0.792,1.167 0.313,0.229 2.521,1.802 1.854,1.458 true 0.104,0.083 0.344,0.26 0.24,0.177 10 false *a 2.552,1.823 3.063,2 0.51,0.177 10 false E1 0.521,0.979 0.833,1.156 0.313,0.177 10 false G70
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G70-33 (E1) - Body ground Power switch off Below 1 Ω



c.

Reconnect the G70 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR