Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID VEHICLE CONTROL ECU › 2019.09–2020.08
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0371631 HYBRID VEHICLE CONTROL ECU A

HYBRID / BATTERY CONTROL  HYBRID VEHICLE CONTROL ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle control ECU assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of hybrid vehicle control ECU assembly Code registration (Immobiliser function)
·

Wireless door lock control system

·

Entry and start system (for entry function)

·

Entry and start system (for start function)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.

NOTICE:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD

Hide 65351A 4.REMOVE BATTERY HOLE COVER

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73900 6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

Hide 58810J 7.REMOVE CONSOLE BOX ASSEMBLY (for RHD)

Hide 67914B 8.REMOVE FRONT DOOR SCUFF PLATE LH (for RHD)

Hide 62112 9.REMOVE COWL SIDE TRIM BOARD LH (for RHD)

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55607 10.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 55550 11.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)

Hide 55433B 12.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for RHD)

Hide 89981 13.REMOVE HYBRID VEHICLE CONTROL ECU ASSEMBLY (for LHD)

a.
A421606

Disconnect the connector.


b.

w/ VEHICLE APPROACHING SPEAKER CONTROLLER:

i.
A421607

Disconnect the connector.



c.
A435243

Disengage the clamp.


d.

Disconnect the 3 hybrid vehicle control ECU assembly connectors as shown in the illustration.


e.
A435245

Remove the 2 nuts and hybrid vehicle control ECU assembly.


Hide 89981 14.REMOVE HYBRID VEHICLE CONTROL ECU ASSEMBLY (for RHD)

a.
A421595

Disengage the 2 clamps.


b.

Disconnect the 4 connectors.


c.
A421596

Disconnect the 5 connectors.


d.

w/ VEHICLE APPROACHING SPEAKER CONTROLLER:

i.
A421597

Disconnect the connector.



e.
A421598

Disconnect the 3 hybrid vehicle control ECU assembly connectors as shown in the illustration.


f.
A421600C03
3.271,1.979 3.427,2.177 0.156,0.198 10 false -
V100135

Bolt
V100136

Nut


Remove the bolt, nut and hybrid vehicle control ECU assembly.


Hide 86572 15.REMOVE VEHICLE APPROACHING SPEAKER CONTROLLER (w/ VEHICLE APPROACHING SPEAKER CONTROLLER)