The immobiliser function compares the ID code that is registered to the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the ID code box (immobiliser code ECU) or hybrid vehicle control ECU assembly, refer to the Service Bulletin.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
After completing repairs, confirm that the problem does not recur.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.
Check for DTCs.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Check that the hybrid control system starts within 5 seconds of the power switch being turned on (READY).
Hybrid control system starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Using an oscilloscope, check the waveform.
| *A | for LHD | *B | for RHD |
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
*b | Approximately 160 ms. |
| *c | Approximately 270 ms. | *d | Approximately 40 ms. |
| *e | Approximately 60 ms. | *f | IMO Waveform |
| *g | IMI Waveform | *h | Waveform A |
| *i | Waveform B | *j | Waveform C |
| *k | Waveform A (detail) | - | - |
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| A30-23 (IMO) - Body ground | Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform B) |
| A30-10 (IMI) - Body ground | Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform A and C) |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G63-23 (IMO) - Body ground | Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform B) |
| G63-10 (IMI) - Body ground | Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform A and C) |
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform A is not output, or has abnormal wavelength or shape | B |
| Waveform B is not output, or has abnormal wavelength or shape | C |
| Waveform C is not output, or has abnormal wavelength or shape | D |
A
B
C
D
Register the ECU communication ID codes.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the hybrid control system starts.
Hybrid control system starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G57 ID code box (immobiliser code ECU) connector.
for LHD:
Disconnect the A30 hybrid vehicle control ECU assembly connector.
for RHD:
Disconnect the G63 hybrid vehicle control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G57-3 (EFII) - A30-23 (IMO) | Always | Below 1 Ω |
| G57-4 (EFIO) - A30-10 (IMI) | Always | Below 1 Ω |
| G57-3 (EFII) or A30-23 (IMO) - Other terminals and body ground | Always | 10 kΩ or higher |
| G57-4 (EFIO) or A30-10 (IMI) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G57-3 (EFII) - G63-23 (IMO) | Always | Below 1 Ω |
| G57-4 (EFIO) - G63-10 (IMI) | Always | Below 1 Ω |
| G57-3 (EFII) or G63-23 (IMO) - Other terminals and body ground | Always | 10 kΩ or higher |
| G57-4 (EFIO) or G63-10 (IMI) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ID code box (immobiliser code ECU) with a new one.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the recognition codes to the ECUs.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID codes.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the hybrid control system starts.
Hybrid control system starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2WD with NICKEL METAL HYDRIDE BATTERY:
for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY:
for 2WD with LITHIUM-ION BATTERY:
for 4WD/AWD with LITHIUM-ION BATTERY: