Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2020.08
RM3620E _51 Engine / Hybrid System _076384 M20A-FKS ENGINE CONTROL _0372800 SFI SYSTEM C

M20A-FKS ENGINE CONTROL  SFI SYSTEM  P085011  Park/Neutral Switch Circuit Short to Ground  


DESCRIPTION

The neutral position switch detects whether the shift lever is in neutral or not and outputs a signal to the ECM. The neutral position switch is installed to the transaxle and is connected to the ECM via a wire harness.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P085011 Park/Neutral Switch Circuit Short to Ground The neutral position switch output voltage is less than 0.12 V for 3 seconds or more (1 trip detection logic).
·

Open or short in neutral position switch circuit

·

Neutral position switch

·

ECM


- DTC stored SAE: P0851

MONITOR DESCRIPTION

When the ignition switch is turned ON and the output voltage of the neutral position switch is less than 0.12 V for 3 seconds or more, the ECM determines that the neutral position switch circuit is malfunctioning and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Neutral position switch
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P085011.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A451323E02
5.542,2.875 6,3.073 0.458,0.198 10 false C40 5.552,3.042 6.01,3.24 0.458,0.198 10 false ECM 5.042,0.76 5.656,0.958 0.615,0.198 10 false VCNP 5.031,1.51 5.646,1.708 0.615,0.198 10 false NPSW 5.052,2.25 5.667,2.448 0.615,0.198 10 false ENPS 4.823,0.771 5.135,0.969 0.313,0.198 10 false 83 4.74,1.521 5.198,1.719 0.458,0.198 10 false 106 4.813,2.25 5.271,2.448 0.458,0.198 10 false 60 0.906,2.927 1.365,3.125 0.458,0.198 10 false C55 2.229,0.771 2.542,0.969 0.313,0.198 10 false W1 2.156,1.49 2.615,1.688 0.458,0.198 10 false TMN 2.271,2.458 2.729,2.656 0.458,0.198 10 false F+ 2.5,2.25 2.656,2.448 0.156,0.198 10 false 3 2.51,1.521 2.667,1.719 0.156,0.198 10 false 2 2.51,0.76 2.667,0.958 0.156,0.198 10 false 1 0.917,3.104 2.552,3.365 1.635,0.26 10 false Neutral Position Switch 1,1.583 1.313,1.781 0.313,0.198 10 false IC 5.677,1.219 6.208,1.49 0.531,0.271 10 false 1 kΩ 5.781,0.656 6.24,0.854 0.458,0.198 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A451316C05
0.615,1.094 0.99,1.385 0.375,0.292 1.677,1.781 1.677,1.167 true 0.99,1.708 1.521,1.167 true 2.323,1.719 1.854,1.167 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 0.688,1.167 1.125,1.49 0.438,0.323 10 false C55 1.552,1.792 2.01,2.094 0.458,0.302 10 false TMN 0.802,1.729 1.26,2.031 0.458,0.302 10 false W1 2.292,1.76 2.75,2.063 0.458,0.302 10 false F+
*a Front view of wire harness connector
(to Neutral Position Switch)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the neutral position switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C55-1 (W1) - C55-3 (F+) Ignition switch ON 4.5 to 5.5 V
C55-2 (TMN) - C55-3 (F+) Ignition switch ON 3.0 to 5.5 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-1 (W1) - C55-2 (TMN) Ignition switch off 0.95 to 1.05 kΩ



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NEUTRAL POSITION SWITCH - ECM)
2.CHECK HARNESS AND CONNECTOR (NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the neutral position switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-1 (W1) - C40-83 (VCNP) Always Below 1 Ω
C55-2 (TMN) or C40-106 (NPSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR