Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076048 NAVIGATION / MULTI INFO DISPLAY _0370120 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

DCM (telematics transceiver)*

·

Harness or connector



*: w/ Telematics Transceiver and for 6 Speakers


WIRING DIAGRAM

E434917E03
0.417,2.167 1.802,2.542 1.385,0.375 10 false Telephone Microphone Assembly 2.323,0.927 2.927,1.115 0.604,0.188 10 false P14 3.521,2.625 5.844,2.865 2.323,0.24 10 false DCM (Telematics Transceiver) 3.521,2.458 4.354,2.719 0.833,0.26 10 false H6*1, H10*2 5.813,2.625 7.063,3.01 1.25,0.385 10 false Radio and Display Receiver Assembly 5.813,2.448 6.156,2.625 0.344,0.177 10 false G2 6.104,0.948 6.542,1.115 0.438,0.167 10 false SNS2 5.75,0.813 6,0.979 0.25,0.167 10 false 25 3.917,1.865 4.354,2.031 0.438,0.167 10 false MCI- 3.458,1.563 3.813,1.771 0.354,0.208 10 false 35*1 1.021,0.948 1.458,1.115 0.438,0.167 10 false SNS2 1.521,0.823 1.688,1 0.167,0.177 10 false 1 1.094,1.885 1.531,2.052 0.438,0.167 10 false MIC- 1.531,1.75 1.698,1.927 0.167,0.177 10 false 2 0.146,0.052 4.885,0.656 4.74,0.604 12 false w/ Telematics Transceiver and for 6 Speakers: 0.656,2.969 2.979,3.208 2.323,0.24 10 false Map Light Assembly 1.802,0.823 2.24,0.99 0.438,0.167 10 false SNS2 2.354,0.74 2.635,0.969 0.281,0.229 10 false 4*1 1.813,1.75 2.25,1.917 0.438,0.167 10 false MCO- 2.365,1.677 2.708,1.917 0.344,0.24 10 false 5*1 2.333,1.885 2.938,2.073 0.604,0.188 10 false P14 2.75,1.885 3.354,2.073 0.604,0.188 10 false P20 2.74,0.927 3.344,1.115 0.604,0.188 10 false P20 2.771,0.729 3.135,1 0.365,0.271 10 false 6*2 2.771,1.688 3.135,1.958 0.365,0.271 10 false 7*2 0.219,3.417 1.75,3.719 1.531,0.302 10 false *1: for TMMR Made 1.698,3.417 3.229,3.719 1.531,0.302 10 false *2: except TMMR Made 0.417,2 1.802,2.375 1.385,0.375 10 false C 3.51,1.75 3.865,1.958 0.354,0.208 10 false 7*2

E434918E01
0.167,0.073 6.01,0.552 5.844,0.479 12 false w/o Telematics Transceiver or for 9 Speakers: 1.583,0.958 2.042,1.188 0.458,0.229 10 false SNS2 2.052,0.823 2.271,1.01 0.219,0.188 10 false 1 5.448,0.823 5.667,1.01 0.219,0.188 10 false 25 5.771,0.958 6.49,1.25 0.719,0.292 10 false SNS2 2.073,1.844 2.531,2.073 0.458,0.229 10 false 2 5.448,1.823 5.729,2.063 0.281,0.24 10 false 22 5.781,1.969 6.24,2.198 0.458,0.229 10 false MIN- 5.74,2.469 6.198,2.698 0.458,0.229 10 false G2 5.74,2.635 6.969,3.021 1.229,0.385 10 false Radio and Display Receiver Assembly 3.094,0.948 3.552,1.177 0.458,0.229 10 false P14 1.01,2.25 2.438,2.74 1.427,0.49 10 false Telephone Microphone Assembly 1.271,2.948 3.229,3.302 1.958,0.354 10 false Map Light Assembly 2.573,1.854 3.031,2.083 0.458,0.229 10 false MCO- 1.604,1.938 2.063,2.167 0.458,0.229 10 false MIC- 2.604,0.833 3.063,1.063 0.458,0.229 10 false SNS2 3.125,0.74 3.583,0.969 0.458,0.229 10 false 4*1 3.115,1.74 3.573,1.969 0.458,0.229 10 false 5*2 3.094,1.938 3.552,2.167 0.458,0.229 10 false P14 3.51,0.948 3.969,1.177 0.458,0.229 10 false P20 3.51,1.938 3.969,2.167 0.458,0.229 10 false P20 3.51,0.75 3.969,0.979 0.458,0.229 10 false 6*2 3.531,1.74 3.99,1.969 0.458,0.229 10 false 7*2 1,2.083 2.427,2.573 1.427,0.49 10 false C 0.188,3.385 2.146,3.74 1.958,0.354 10 false *1: for TMMR Made 1.646,3.385 3.604,3.74 1.958,0.354 10 false *2: except TMMR Made

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.


·

When replacing the DCM (telematics transceiver), make sure to replace it with a new one. (w/ Telematics Transceiver)



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Telematics Transceiver and for 6 Speakers A
w/o Telematics Transceiver or for 9 Speakers B



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the P14*1 or P20*2 map light assembly connector.

*1: for TMMR Made

*2: except TMMR Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMR Made
Tester Connection Condition Specified Condition
G2-25 (SNS2) - P14-4 (SNS2) Always Below 1 Ω
G2-25 (SNS2) - Body ground Always 10 kΩ or higher

except TMMR Made
Tester Connection Condition Specified Condition
G2-25 (SNS2) - P20-6 (SNS2) Always Below 1 Ω
G2-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)

*1: for TMMR Made

*2: except TMMR Made


a.

Disconnect the H6*1 or H10*2 DCM (telematics transceiver) connector.


b.

Disconnect the P14*1 or P20*2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMR Made
Tester Connection Condition Specified Condition
H6-35 (MCI-) - P14-5 (MCO-) Always Below 1 Ω
H6-35 (MCI-) - Body ground Always 10 kΩ or higher

except TMMR Made
Tester Connection Condition Specified Condition
H10-7 (MCI-) - P20-7 (MCO-) Always Below 1 Ω
H10-7 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DCM (TELEMATICS TRANSCEIVER) (MCI-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DCM (TELEMATICS TRANSCEIVER) (MCI-)
a.
E450900C04
1.563,2.521 2.042,2.792 0.479,0.271 1.573,0.125 2.052,0.396 0.479,0.271 0.625,1.917 0.854,1.917 0.854,1.917 1.385,1.26 true 2.688,2.229 2.49,2.229 2.49,2.229 2.198,3.333 true 1.698,0.188 2.135,0.375 0.438,0.188 10 false H6 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.677,2.573 2.354,2.792 0.677,0.219 10 false H10 0.281,1.813 0.719,2 0.438,0.188 10 false MCI- 2.75,2.146 3.188,2.333 0.438,0.188 10 false MCI- 1.344,0.052 1.656,0.25 0.313,0.198 10 false *A 1.333,2.51 1.646,2.708 0.313,0.198 10 false *B
*A for TMMR Made
*B except TMMR Made
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMR Made
Tester Connection Condition Specified Condition
H6-35 (MCI-) - Body ground Always Below 1 Ω

except TMMR Made
Tester Connection Condition Specified Condition
H10-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the P14*1 or P20*2 map light assembly connector.

*1: for TMMR Made

*2: except TMMR Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMR Made
Tester Connection Condition Specified Condition
G2-25 (SNS2) - P14-4 (SNS2) Always Below 1 Ω
G2-22 (MIN-) - P14-5 (MCO-) Always Below 1 Ω
G2-25 (SNS2) - Body ground Always 10 kΩ or higher
G2-22 (MIN-) - Body ground Always 10 kΩ or higher

except TMMR Made
Tester Connection Condition Specified Condition
G2-25 (SNS2) - P20-6 (SNS2) Always Below 1 Ω
G2-22 (MIN-) - P20-7 (MCO-) Always Below 1 Ω
G2-25 (SNS2) - Body ground Always 10 kΩ or higher
G2-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAP LIGHT ASSEMBLY
a.
E434903C03
1.792,1.573 1.99,0.865 1.99,0.865 2.188,0.865 true 1.26,0.854 1.469,0.854 1.469,0.854 1.635,1.552 true 1.938,3.667 2.135,2.958 2.135,2.958 2.333,2.958 true 1.427,2.99 1.635,2.99 1.635,2.99 1.802,3.688 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.865,0.771 1.438,1.135 0.573,0.365 10 false MCO- 2.26,0.781 2.885,1.083 0.625,0.302 10 false SNS2 2.396,2.885 3.042,3.177 0.646,0.292 10 false SNS2 0.969,2.906 1.646,3.25 0.677,0.344 10 false MCO- 0.5,0.958 0.813,1.156 0.313,0.198 10 false *A 0.625,3.115 0.938,3.313 0.313,0.198 10 false *B
*A except TMMR Made
*B for TMMR Made
*a Component without harness connected
(Map Light Assembly)


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except TMMR Made
Tester Connection Condition Specified Condition
6 (SNS2) - 7 (MCO-) Always Below 1 Ω

for TMMR Made
Tester Connection Condition Specified Condition
4 (SNS2) - 5 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

7.INSPECT MAP LIGHT ASSEMBLY
7.INSPECT MAP LIGHT ASSEMBLY
a.
E434904C09
0.479,4.104 0.875,4.354 0.396,0.25 1.49,1.052 1.24,0.323 1.24,0.323 1.052,0.323 true 1.792,2.719 1.958,2.073 1.958,2.073 2.156,2.073 true 1.646,2.708 1.438,2.052 1.438,2.052 1.25,2.052 true 1.646,1.042 1.885,0.323 1.885,0.323 2.083,0.323 true 1.292,4.208 1.115,3.729 1.115,3.729 0.927,3.729 true 1.448,4.208 1.615,3.698 1.615,3.698 1.813,3.698 true 0.063,0.271 0.375,0.469 0.313,0.198 10 false *a 2.156,0.229 2.75,0.521 0.594,0.292 10 false SNS2 0.646,0.229 1.219,0.469 0.573,0.24 10 false MCO- 0.625,4.156 0.938,4.354 0.313,0.198 10 false C 0.51,3.635 1.01,3.854 0.5,0.219 10 false SNS2 1.906,3.615 2.385,3.823 0.479,0.208 10 false MIC- 0.833,1.969 1.406,2.208 0.573,0.24 10 false MCO- 2.219,1.99 2.781,2.24 0.563,0.25 10 false SNS2 0.135,3.521 0.448,3.719 0.313,0.198 10 false *b 0.104,1.99 0.417,2.188 0.313,0.198 10 false *a 0.281,0.604 0.594,0.802 0.313,0.198 10 false *A 0.448,2.292 0.76,2.49 0.313,0.198 10 false *B
*A except TMMR Made
*B for TMMR Made
*a Component without harness connected
(Map Light Assembly [Wire Harness Side])
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except TMMR Made
Tester Connection Condition Specified Condition
6 (SNS2) - C-1 (SNS2) Always Below 1 Ω
7 (MCO-) - C-2 (MIC-) Always Below 1 Ω

for TMMR Made
Tester Connection Condition Specified Condition
4 (SNS2) - C-1 (SNS2) Always Below 1 Ω
5 (MCO-) - C-2 (MIC-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY