Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076048 NAVIGATION / MULTI INFO DISPLAY _0370120 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Radio Receiver and Telematics Transceiver  


DESCRIPTION

The DCM (telematics transceiver) sends a mute signal to the radio and display receiver assembly.

The radio and display receiver assembly controls the volume according to the mute signal from the DCM (telematics transceiver).

WIRING DIAGRAM

E448123E02
1.271,1.031 1.885,1.229 0.615,0.198 10 false TMUT 1.729,0.917 2.344,1.115 0.615,0.198 10 false 3 5.115,0.708 5.729,0.906 0.615,0.198 10 false 17*1 5.531,1.021 6.146,1.219 0.615,0.198 10 false MUTE 0.396,1.906 1.01,2.104 0.615,0.198 10 false G2 0.406,2.063 2.802,2.375 2.396,0.313 10 false Radio and Display Receiver Assembly 5.094,2.094 7.01,2.385 1.917,0.292 10 false DCM (Telematics Transceiver) 5.115,1.938 6.052,2.24 0.938,0.302 10 false H6*1, H10*2 5.115,0.906 5.729,1.104 0.615,0.198 10 false 14*2 0.573,2.458 2.521,2.781 1.948,0.323 10 false *1: for TMMR Made 2.427,2.469 4.375,2.792 1.948,0.323 10 false *2: except TMMR Made

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.


·

When replacing the DCM (telematics transceiver), make sure to replace it with a new one.



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for TMMR Made A
except TMMR Made B




A

2.INSPECT DCM (TELEMATICS TRANSCEIVER)

B

5.INSPECT DCM (TELEMATICS TRANSCEIVER)
2.INSPECT DCM (TELEMATICS TRANSCEIVER)
a.
E366538C12
1.5,0.802 1.896,1.052 0.396,0.25 1.396,1.896 1.021,0.906 true 0.188,0.125 0.5,0.323 0.313,0.198 10 false *a 0.792,0.708 1.302,0.917 0.51,0.208 10 false MUTE 1.615,0.833 1.927,1.031 0.313,0.198 10 false H6
*a Component with harness connected
(DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H6-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the H6 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-3 (TMUT) - H6-17 (MUTE) Always Below 1 Ω
G2-3 (TMUT) or H6-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT SIGNAL)
a.
E176650C99
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 true 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.646,0.771 1.99,0.969 0.344,0.198 10 false H6
*a Front view of wire harness connector
(to DCM [Telematics Transceiver])


Disconnect the DCM (telematics transceiver) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-17 (MUTE) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE DCM (TELEMATICS TRANSCEIVER)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.INSPECT DCM (TELEMATICS TRANSCEIVER)
a.
E427272C29
1.469,0.563 1.938,0.865 0.469,0.302 1.063,1.688 0.833,0.979 0.833,0.979 0.688,0.979 true 1.594,0.635 2.219,0.969 0.625,0.333 10 false H10 0.25,0.885 0.74,1.083 0.49,0.198 10 false MUTE 0.198,0.115 0.51,0.313 0.313,0.198 10 false *a
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H10-14 (MUTE) - Body ground Ignition switch ON
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the H10 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-3 (TMUT) - H10-14 (MUTE) Always Below 1 Ω
G2-3 (TMUT) or H10-14 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E427085C11
1.469,0.208 1.906,0.469 0.438,0.26 2.385,1.021 2.521,0.552 2.521,0.552 2.698,0.552 true 1.563,0.26 2.052,0.542 0.49,0.281 10 false H10 2.771,0.469 3.26,0.667 0.49,0.198 10 false MUTE 0.188,0.104 0.5,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to DCM [Telematics Transceiver])


Disconnect the DCM (telematics transceiver) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H10-14 (MUTE) - Body ground Ignition switch ON 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE DCM (TELEMATICS TRANSCEIVER)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY