Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2020.08
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370280 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver  


DESCRIPTION

The DCM (telematics transceiver) sends a mute signal to the stereo component amplifier assembly.

The stereo component amplifier assembly controls the volume according to the mute signal from the DCM (telematics transceiver).

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source. If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E380010E97
1,1.531 1.458,1.729 0.458,0.198 10 false M3 1,1.729 2.74,2.094 1.74,0.365 10 false Stereo Component Amplifier Assembly 4.969,0.781 5.208,0.99 0.24,0.208 10 false 14 2.052,0.771 2.281,0.958 0.229,0.188 10 false 24 1.521,0.927 1.979,1.125 0.458,0.198 10 false TMUT 5.292,0.896 5.781,1.094 0.49,0.198 10 false MUTE 4.99,1.531 5.448,1.729 0.458,0.198 10 false H10 5,1.719 6.938,1.958 1.938,0.24 10 false DCM (Telematics Transceiver)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the DCM (telematics transceiver), make sure to replace it with a new one.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK DCM (TELEMATICS TRANSCEIVER)
a.
E427105C37
1.469,0.563 1.938,0.865 0.469,0.302 1.052,1.698 0.875,0.792 0.875,0.792 0.688,0.792 true 1.563,0.635 2.417,1.104 0.854,0.469 10 false H10 0.271,0.708 0.76,0.906 0.49,0.198 10 false MUTE 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H10-14 (MUTE) - Body ground Ignition switch ACC, audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the M3 stereo component amplifier assembly connector.


b.

Disconnect the H10 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M3-24 (TMUT) - H10-14 (MUTE) Always Below 1 Ω
M3-24 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the DCM (telematics transceiver) connector.


b.
E427085C13
1.469,0.208 1.906,0.469 0.438,0.26 2.385,1.021 2.521,0.552 2.521,0.552 2.698,0.552 true 1.552,0.26 2.063,0.542 0.51,0.281 10 false H10 2.771,0.469 3.26,0.667 0.49,0.198 10 false MUTE 0.188,0.104 0.5,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H10-14 (MUTE) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE DCM (TELEMATICS TRANSCEIVER)

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY