The side collision sensor LH circuit consists of the airbag sensor assembly, side airbag pressure sensor LH and No. 2 side airbag sensor assembly LH*.
The side airbag pressure sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the SRS should be deployed.
These DTCs are stored when a malfunction is detected in the side airbag pressure sensor LH or airbag sensor assembly.
*: w/ Rear Airbag Sensor
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B167A | Front Door Pressure Sensor LH | Either condition is met:
·
A side airbag pressure sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
Side airbag pressure sensor LH ·
Airbag sensor assembly |
Comes on | Not applicable |
| B167E | Front Door Pressure Sensor Threshold Malfunction (LH) | Either condition is met:
·
A side airbag pressure sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
Side airbag pressure sensor LH ·
Airbag sensor assembly |
Comes on | Not applicable |
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
| Proceed to |
|---|
| w/ Rear Airbag Sensor |
| w/o Rear Airbag Sensor |
w/ Rear Airbag Sensor
w/o Rear Airbag Sensor
| *1 | Side Airbag Pressure Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Interchange the side airbag pressure sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B167A or B167E is output |
| DTC B166C or B166F is output |
| DTCs B166C, B166F, B167A and B167E are not output |
Codes other than DTCs B166C, B166F, B167A and B167E may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors to them.
DTC B167A or B167E is output
DTC B166C or B166F is output
DTCs B166C, B166F, B167A and B167E are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Side Airbag Pressure Sensor RH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Interchange the side airbag pressure sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B167A or B167E is output |
| DTC B166C or B166F is output |
| DTCs B166C, B166F, B167A and B167E are not output |
Codes other than DTCs B166C, B166F, B167A and B167E may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors to them.
DTC B167A or B167E is output
DTC B166C or B166F is output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
DTCs B166C, B166F, B167A and B167E are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING