The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 2 side airbag sensor assembly removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
w/o Occupant Classification System:
for Gasoline Model with Occupant Classification System:
for HV Model with Occupant Classification System:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
6.REMOVE REAR SEAT ASSEMBLY
67918E
7.REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)
62552F
8.REMOVE REAR SEAT SIDE GARNISH LH
Remove the rear side of the rear door opening trim weatherstrip LH so that the rear seat No. 3 side garnish LH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>REMOVAL
Remove the rear seat No. 3 side garnish LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
89860C
9.REMOVE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)
| *a | Housing Lock | *b | CPA |
| *c | CPA Upper Part | - | - |
Push the housing lock again and disconnect the connector.
Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.
After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.
| *a | Correct | *b | Incorrect |
| *c | CPA | *d | Housing |
|
Remove in this Direction |
Remove the bolt.
Loosen the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly claw is easily damaged.
If the No. 2 side airbag sensor assembly has been dropped, replace it with a new one.
Detach the claw and remove the No. 2 side airbag sensor assembly.