Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/o Occupant Classification System) › from 2020.08
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0378287 AIRBAG SYSTEM(w/o Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  B167B  Lost Communication with Front Door Pressure Sensor LH  B167C  Front Door Pressure Sensor LH Initialization Incomplete  


DESCRIPTION

The side collision sensor LH circuit consists of the airbag sensor assembly, side airbag pressure sensor LH and No. 2 side airbag sensor assembly LH*.

The side airbag pressure sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the SRS should be deployed.

These DTCs are stored when a malfunction is detected in the circuit for the side collision sensor LH circuit.

*: w/ Rear Airbag Sensor


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B167B Lost Communication with Front Door Pressure Sensor LH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

·

A side airbag pressure sensor LH malfunction.

·

A No. 2 side airbag sensor assembly LH malfunction*.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire LH

·

Side airbag pressure sensor LH

·

No. 2 side airbag sensor assembly LH*

·

Airbag sensor assembly


Comes on Not applicable
B167C Front Door Pressure Sensor LH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

·

A side airbag pressure sensor LH malfunction.

·

A No. 2 side airbag sensor assembly LH malfunction*.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire LH

·

Side airbag pressure sensor LH

·

No. 2 side airbag sensor assembly LH*

·

Airbag sensor assembly


Comes on Not applicable

*: w/ Rear Airbag Sensor


WIRING DIAGRAM

w/ Rear Airbag Sensor:
C401868E36
5.375,2.083 6.99,2.344 1.615,0.26 10 false Airbag Sensor Assembly 5.375,1.927 6.208,2.125 0.833,0.198 10 false N21 5.677,0.875 6.51,1.073 0.833,0.198 10 false BBL+ 5.698,1.458 6.531,1.656 0.833,0.198 10 false BBL- 5.406,0.76 6.24,0.958 0.833,0.198 10 false 32 5.406,1.365 6.24,1.563 0.833,0.198 10 false 31 1.615,0.75 2.448,0.948 0.833,0.198 10 false 4 1.635,1.313 2.469,1.51 0.833,0.198 10 false 3 1.146,0.854 1.979,1.052 0.833,0.198 10 false BCL+ 1.104,1.469 1.938,1.667 0.833,0.198 10 false BCL- 1.135,2.792 1.969,2.99 0.833,0.198 10 false BDL+ 1.146,3.333 1.979,3.531 0.833,0.198 10 false BDL- 1.604,2.688 2.438,2.885 0.833,0.198 10 false 1 1.594,3.24 2.427,3.438 0.833,0.198 10 false 2 4.083,2.813 4.917,3.01 0.833,0.198 10 false BDL+ 4.094,3.354 4.927,3.552 0.833,0.198 10 false BDL- 0.552,3.969 2.177,4.313 1.625,0.344 10 false No. 2 Side Airbag Sensor Assembly LH 0.542,3.813 1.302,4.146 0.76,0.333 10 false N22 4.01,3.979 6.208,4.271 2.198,0.292 10 false Side Airbag Pressure Sensor LH 4.021,3.823 4.781,4.156 0.76,0.333 10 false J9 2.698,3.344 3.458,3.677 0.76,0.333 10 false JN2 2.708,2.813 3.469,3.146 0.76,0.333 10 false JN2 2.781,3.156 3.615,3.354 0.833,0.198 10 false 2 2.781,2.594 3.615,2.792 0.833,0.198 10 false 1 3.906,2.719 4.74,2.917 0.833,0.198 10 false 2 3.906,3.26 4.74,3.458 0.833,0.198 10 false 1 2.698,2.99 3.531,3.188 0.833,0.198 10 false BDL+ 2.688,3.563 3.521,3.76 0.833,0.198 10 false BDL-

w/o Rear Airbag Sensor:
E444927E03
5.344,1.958 5.802,2.156 0.458,0.198 10 false N21 5.333,2.135 6.927,2.375 1.594,0.24 10 false Airbag Sensor Assembly 5.552,0.75 6.01,0.948 0.458,0.198 10 false BBL+ 5.552,1.375 6.01,1.573 0.458,0.198 10 false BBL- 5.271,0.646 5.552,0.844 0.281,0.198 10 false 32 5.271,1.25 5.552,1.448 0.281,0.198 10 false 31 3.458,0.771 3.74,0.969 0.281,0.198 10 false JN2 3.469,1.385 3.75,1.583 0.281,0.198 10 false JN2 3.51,0.573 3.792,0.771 0.281,0.198 10 false 1 3.521,1.177 3.802,1.375 0.281,0.198 10 false 2 3.417,0.979 3.875,1.177 0.458,0.198 10 false BDL+ 3.427,1.594 3.885,1.792 0.458,0.198 10 false BDL- 1.625,0.635 1.906,0.833 0.281,0.198 10 false 2 1.625,1.25 1.906,1.448 0.281,0.198 10 false 1 1.146,0.771 1.604,0.969 0.458,0.198 10 false BDL+ 1.135,1.406 1.594,1.604 0.458,0.198 10 false BDL- 0.094,1.781 0.552,1.979 0.458,0.198 10 false J9 0.083,1.958 2.302,2.25 2.219,0.292 10 false Side Airbag Pressure Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Proceed to
w/ Rear Airbag Sensor
w/o Rear Airbag Sensor



w/ Rear Airbag Sensor

2.CHECK CONNECTION OF CONNECTORS

w/o Rear Airbag Sensor

9.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the No. 2 side airbag sensor assembly LH and side airbag pressure sensor LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.
C301835C22
0.604,1.458 0.917,1.615 0.313,0.156 10 false *1 2.573,1.469 2.885,1.625 0.313,0.156 10 false *2 1.385,0.802 1.698,0.958 0.313,0.156 10 false *3 1.896,0.792 2.208,0.948 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire


Disconnect the connectors from the No. 2 side airbag sensor assembly LH and side airbag pressure sensor LH.


b.

Check that the connectors (on the No. 2 side airbag sensor assembly LH side and side airbag pressure sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

4.CHECK SIDE AIRBAG PRESSURE SENSOR LH CIRCUIT

The connectors are deformed or damaged

REPLACE FRONT DOOR WIRE LH OR FLOOR WIRE

4.CHECK SIDE AIRBAG PRESSURE SENSOR LH CIRCUIT
a.
C411558C02
0.74,0.813 1.125,1.063 0.385,0.25 2.469,2.917 2.885,3.125 0.417,0.208 1.313,1.5 1.479,1.5 1.479,1.5 1.719,0.969 true 2.406,1.5 2.229,1.5 2.229,1.5 1.917,0.969 true 0.927,3.365 1.073,3.365 1.073,3.365 1.563,3.563 true 1.417,2.938 1.531,2.938 1.531,2.938 1.729,3.563 true 1.865,4.063 2.083,4.208 2.083,4.208 2.24,4.208 true 0.448,2.583 0.76,2.74 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.229,2.302 1.542,2.458 0.313,0.156 10 false *3 1.792,2.333 2.104,2.49 0.313,0.156 10 false *4 0.76,0.292 1.073,0.448 0.313,0.156 10 false *a 0.531,2.927 0.844,3.083 0.313,0.156 10 false *b 0.865,0.854 1.177,1.01 0.313,0.156 10 false J9 2.396,2.125 2.708,2.281 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.625,2.115 1.938,2.271 0.313,0.156 10 false C 1.469,2.115 1.781,2.271 0.313,0.156 10 false D 1.01,2.115 1.323,2.271 0.313,0.156 10 false E 0.708,2.125 1.021,2.281 0.313,0.156 10 false F 2.552,2.938 2.865,3.094 0.313,0.156 10 false N22 2.479,1.417 3.042,1.677 0.563,0.26 10 false BDL+ 0.938,1.417 1.5,1.677 0.563,0.26 10 false BDL- 1.052,2.854 1.615,3.115 0.563,0.26 10 false BDL- 0.531,3.281 1.094,3.542 0.563,0.26 10 false BDL+ 2.313,4.125 2.625,4.281 0.313,0.156 10 false *5
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J9-2 (BDL+) - Body ground Ignition switch ON Below 1 V
J9-1 (BDL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-2 (BDL+) - J9-1 (BDL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-2 (BDL+) - J9-1 (BDL-) Always 1 MΩ or higher
J9-2 (BDL+) - Body ground Always 1 MΩ or higher
J9-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE AIRBAG PRESSURE SENSOR LH

NG

7.CHECK CONNECTORS
5.CHECK SIDE AIRBAG PRESSURE SENSOR LH
a.
C238395C07
0.729,1.563 1,1.74 0.271,0.177 10 false *1 2.583,1.542 2.896,1.75 0.313,0.208 10 false *2
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly LH


Connect the connector to the No. 2 side airbag sensor assembly LH.


b.

Interchange the side airbag pressure sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B167B or B167C is output
DTC B166D or B166E is output
DTCs B166D, B166E, B167B and B167C are not output


HINT:

Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors to them.



DTC B167B or B167C is output

6.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

DTC B166D or B166E is output

DTCs B166D, B166E, B167B and B167C are not output

6.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH
a.

Interchange the No. 2 side airbag sensor assembly LH with RH and connect the connectors to them.


C370762C19
0.875,0.938 1.188,1.135 0.313,0.198 10 false *1 2.406,1.313 2.719,1.51 0.313,0.198 10 false *2
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B167B or B167C is output
DTC B166D or B166E is output
DTCs B166D, B166E, B167B and B167C are not output


HINT:

Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


j.

Return the No. 2 side airbag sensor assembly RH and LH to their original positions and connect the connectors to them.



DTC B167B or B167C is output

DTC B166D or B166E is output

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

DTCs B166D, B166E, B167B and B167C are not output

7.CHECK CONNECTORS
a.
B510595C03
0.458,1.479 0.771,1.635 0.313,0.156 10 false *1 2.823,1.5 3.135,1.656 0.313,0.156 10 false *2 1.25,1.229 1.563,1.385 0.313,0.156 10 false *3 2.021,1.24 2.333,1.396 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire


Disconnect the floor wire connector from the front door wire LH.


b.

Check that the connectors (on the floor wire side and front door wire LH side) are not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

8.CHECK FLOOR WIRE

The connector is deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH

8.CHECK FLOOR WIRE
a.
C411661C02
0.615,3.5 0.948,3.75 0.333,0.25 0.552,0.906 0.917,1.146 0.365,0.24 2.396,0.469 2.25,0.469 2.25,0.469 1.917,0.74 true 1.177,0.469 1.323,0.469 1.323,0.469 1.667,0.729 true 2.052,3.125 1.906,3.125 1.906,3.125 1.823,3.677 true 2.698,3.135 2.573,3.135 2.573,3.135 1.99,3.667 true 2.344,4.333 2.229,4.333 2.229,4.333 2.083,4.094 true 0.167,0.177 0.479,0.385 0.313,0.208 10 false *a 0.625,0.948 0.938,1.156 0.313,0.208 10 false JN2 2.563,2.26 2.781,2.479 0.219,0.219 10 false A 2.24,2.271 2.458,2.49 0.219,0.219 10 false B 1.792,2.271 2.01,2.49 0.219,0.219 10 false C 1.49,2.271 1.708,2.49 0.219,0.219 10 false D 1.031,2.271 1.25,2.49 0.219,0.219 10 false E 0.719,2.271 0.938,2.49 0.219,0.219 10 false F 0.385,2.719 0.698,2.927 0.313,0.208 10 false *1 1.229,2.479 1.542,2.688 0.313,0.208 10 false *3 2.771,2.708 3.083,2.917 0.313,0.208 10 false *2 1.99,2.458 2.302,2.667 0.313,0.208 10 false *4 0.542,3.031 0.854,3.24 0.313,0.208 10 false *b 0.656,3.531 0.969,3.74 0.313,0.208 10 false N22 2.479,0.375 2.938,0.583 0.458,0.208 10 false BDL+ 0.792,0.375 1.208,0.583 0.417,0.208 10 false BDL- 2.104,3.042 2.615,3.25 0.51,0.208 10 false BDL+ 2.771,3.063 3.281,3.271 0.51,0.208 10 false BDL- 2.406,4.25 2.719,4.458 0.313,0.208 10 false *5
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Front Door Wire LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
JN2-1 (BDL+) - Body ground Ignition switch ON Below 1 V
JN2-2 (BDL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JN2-1 (BDL+) - JN2-2 (BDL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JN2-1 (BDL+) - JN2-2 (BDL-) Always 1 MΩ or higher
JN2-1 (BDL+) - Body ground Always 1 MΩ or higher
JN2-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

9.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag pressure sensor LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

10.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

10.CHECK CONNECTORS
a.
E449101C01
0.427,0.979 0.74,1.135 0.313,0.156 10 false *1 2.573,1.469 2.885,1.625 0.313,0.156 10 false *2 1.146,0.771 1.458,0.927 0.313,0.156 10 false *3 1.667,0.771 1.979,0.927 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Front Door Wire LH
*4 Floor Wire


Disconnect the connectors from the airbag sensor assembly and side airbag pressure sensor LH.


b.

Check that the connectors (on the airbag sensor assembly side and side airbag pressure sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

11.CHECK SIDE AIRBAG PRESSURE SENSOR LH CIRCUIT

The connectors are deformed or damaged

REPLACE FRONT DOOR WIRE LH OR FLOOR WIRE

11.CHECK SIDE AIRBAG PRESSURE SENSOR LH CIRCUIT
a.
E449102C01
1.104,3.552 1.521,3.802 0.417,0.25 0.896,0.552 1.313,0.802 0.417,0.25 1.375,1.115 1.51,1.115 1.51,1.115 1.677,0.688 true 2.219,1.115 2.094,1.115 2.094,1.115 1.865,0.688 true 2.104,4.417 2.219,4.417 2.219,4.417 2.292,4.219 true 2.74,3.531 2.604,3.531 2.604,3.531 2.323,3.938 true 2.5,2.979 2.365,2.979 2.365,2.979 2.25,3.927 true 0.708,1.781 0.854,1.969 0.146,0.188 10 false F 0.427,2.24 0.635,2.427 0.208,0.188 10 false *1 0.969,1.771 1.104,1.958 0.135,0.188 10 false E 2.031,1.771 2.167,1.958 0.135,0.188 10 false B 1.156,1.969 1.365,2.156 0.208,0.188 10 false *3 1.76,1.969 1.969,2.156 0.208,0.188 10 false *4 2.292,1.771 2.427,1.958 0.135,0.188 10 false A 2.677,2.594 2.885,2.781 0.208,0.188 10 false *2 1.021,0.615 1.281,0.802 0.26,0.188 10 false J9 0.656,0.167 0.865,0.354 0.208,0.188 10 false *a 1.198,3.604 1.51,3.76 0.313,0.156 10 false N21 0.948,2.865 1.156,3.052 0.208,0.188 10 false *b 2.823,3.469 3.292,3.646 0.469,0.177 10 false BBL+ 1.906,4.333 2.125,4.479 0.219,0.146 10 false *5 2.583,2.906 2.99,3.073 0.406,0.167 10 false BBL- 1.417,1.771 1.552,1.938 0.135,0.167 10 false D 1.573,1.771 1.708,1.938 0.135,0.167 10 false C 0.979,1.052 1.552,1.229 0.573,0.177 10 false BDL- 2.302,1.031 2.885,1.188 0.583,0.156 10 false BDL+
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor LH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J9-2 (BDL+) - Body ground Engine switch on (IG) Below 1 V
J9-1 (BDL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 32 (BBL+) and 31 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-2 (BDL+) - J9-1 (BDL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-2 (BDL+) - J9-1 (BDL-) Always 1 MΩ or higher
J9-2 (BDL+) - Body ground Always 1 MΩ or higher
J9-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK SIDE AIRBAG PRESSURE SENSOR LH

NG

13.CHECK CONNECTORS
12.CHECK SIDE AIRBAG PRESSURE SENSOR LH
a.
E449103C01
0.552,0.969 0.823,1.146 0.271,0.177 10 false *1 2.583,1.542 2.896,1.75 0.313,0.208 10 false *2
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the side airbag pressure sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B167B or B167C is output
DTC B166D or B166E is output
DTCs B166D, B166E, B167B and B167C are not output


HINT:

Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors to them.



DTC B167B or B167C is output

DTC B166D or B166E is output

DTCs B166D, B166E, B167B and B167C are not output

13.CHECK CONNECTORS
a.
E449104C01
0.458,0.969 0.771,1.125 0.313,0.156 10 false *1 2.583,1.49 2.896,1.646 0.313,0.156 10 false *2 1.104,0.75 1.417,0.906 0.313,0.156 10 false *3 1.698,0.781 2.01,0.938 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Front Door Wire LH
*4 Floor Wire


Disconnect the floor wire connector from the front door wire LH.


b.

Check that the connectors (on the floor wire side and front door wire LH side) are not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

14.CHECK FLOOR WIRE

The connector is deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH

14.CHECK FLOOR WIRE
a.
E449105C01
1.083,3.583 1.5,3.833 0.417,0.25 1.042,0.635 1.458,0.885 0.417,0.25 1.333,0.25 1.5,0.25 1.5,0.25 1.719,0.531 true 2.167,0.25 2,0.25 2,0.25 1.875,0.552 true 1.958,4.406 2.125,4.406 2.125,4.406 2.271,4.188 true 1.281,3.208 1.448,3.208 1.448,3.208 2.219,3.948 true 1.625,2.948 1.792,2.948 1.792,2.948 2.323,3.927 true 0.99,0.198 1.677,0.406 0.688,0.208 10 false BDL- 2.229,0.177 2.656,0.573 0.427,0.396 10 false BDL+ 2.292,1.771 2.479,2 0.188,0.229 10 false A 2.073,1.771 2.26,2 0.188,0.229 10 false B 1.604,1.771 1.792,2 0.188,0.229 10 false C 1.396,1.771 1.583,2 0.188,0.229 10 false D 0.958,1.771 1.177,2.031 0.219,0.26 10 false E 0.729,1.781 0.948,2.042 0.219,0.26 10 false F 2.625,2.604 2.885,2.833 0.26,0.229 10 false *2 0.406,2.25 0.667,2.479 0.26,0.229 10 false *1 1.135,0.698 1.469,0.875 0.333,0.177 10 false JN2 0.646,0.167 0.906,0.396 0.26,0.229 10 false *a 0.927,2.885 1.188,3.115 0.26,0.229 10 false *b 1.135,1.969 1.396,2.198 0.26,0.229 10 false *3 1.792,1.969 2.052,2.198 0.26,0.229 10 false *4 1.188,3.635 1.51,3.813 0.323,0.177 10 false N21 1.26,2.885 1.948,3.094 0.688,0.208 10 false BBL+ 0.938,3.146 1.51,3.354 0.573,0.208 10 false BBL- 1.771,4.375 2.031,4.604 0.26,0.229 10 false *5
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Front Door Wire LH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
JN2-1 (BDL+) - Body ground Ignition switch ON Below 1 V
JN2-2 (BDL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 32 (BBL+) and 31 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JN2-1 (BDL+) - JN2-2 (BDL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JN2-1 (BDL+) - JN2-2 (BDL-) Always 1 MΩ or higher
JN2-1 (BDL+) - Body ground Always 1 MΩ or higher
JN2-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE