Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.08
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "DCM" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "DCM" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "DCM" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "DCM Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Telephone transceiver assembly branch wire or connector

·

Power source circuit of telephone transceiver assembly

·

Telephone transceiver assembly ground circuit

·

Telephone transceiver assembly



WIRING DIAGRAM

for ERA-GLONASS
C393551E10
1.031,1.958 3.313,2.156 2.281,0.198 10 false from Engine Stop and Start ECU*1 0.167,1.5 2.281,1.698 2.115,0.198 10 false No. 5 CAN Junction Connector 0.167,1.323 0.781,1.521 0.615,0.198 10 false G105 1.031,3.125 3.313,3.323 2.281,0.198 10 false from Engine Stop and Start ECU*1 1.01,4.292 3.292,4.49 2.281,0.198 10 false from Engine Stop and Start ECU*1 5.208,5.76 5.667,5.958 0.458,0.198 10 false H6 5.208,5.958 6.583,6.448 1.375,0.49 10 false Telephone Transceiver Assembly 2.208,2.521 3.323,2.719 1.115,0.198 10 false from Battery*2 1.969,3.677 3.25,3.875 1.281,0.198 10 false from ACC Relay*2 1.667,4.885 3.479,5.219 1.813,0.333 10 false from IG2 NO. 2 Relay*2 3.958,2.375 4.417,2.573 0.458,0.198 10 false DCM*2 3.813,3.552 4.688,3.771 0.875,0.219 10 false ECU-ACC*2 3.615,4.698 4.698,4.906 1.083,0.208 10 false ECU-IG2 NO.3*2 0.25,5.552 2.531,5.75 2.281,0.198 10 false *1: w/ Stop and Start System 0.25,5.969 2.531,6.167 2.281,0.198 10 false *2: w/o Stop and Start System 4,1.833 4.313,2.031 0.313,0.198 10 false *1 4.917,2.25 5.229,2.448 0.313,0.198 10 false *2 4.917,3.417 5.229,3.615 0.313,0.198 10 false *2 4.021,3 4.333,3.198 0.313,0.198 10 false *1 4.021,4.167 4.333,4.365 0.313,0.198 10 false *1 4.917,4.583 5.229,4.781 0.313,0.198 10 false *2 5.75,0.552 6.208,0.75 0.458,0.198 10 false CANP 5.75,1.083 6.208,1.281 0.458,0.198 10 false CANN 5.75,3.125 6.208,3.323 0.458,0.198 10 false ACC 5.75,4.292 6.208,4.49 0.458,0.198 10 false IG2 5.75,1.948 6.063,2.146 0.313,0.198 10 false +B 5.75,5.354 6.063,5.552 0.313,0.198 10 false E 1.583,0.417 1.896,0.615 0.313,0.198 10 false 3 1.604,0.948 1.917,1.146 0.313,0.198 10 false 14 5.333,0.427 5.646,0.625 0.313,0.198 10 false 15 5.344,0.958 5.656,1.156 0.313,0.198 10 false 16 5.417,1.833 5.573,2.031 0.156,0.198 10 false 1 5.427,3 5.583,3.198 0.156,0.198 10 false 8 5.427,4.167 5.583,4.365 0.156,0.198 10 false 7 5.427,5.229 5.583,5.427 0.156,0.198 10 false 4

for eCall
C447102E02
1.031,1.958 3.313,2.156 2.281,0.198 10 false from Engine Stop and Start ECU*1 0.167,1.5 2.281,1.698 2.115,0.198 10 false No. 5 CAN Junction Connector 0.167,1.323 0.781,1.521 0.615,0.198 10 false G105 1,4.292 3.281,4.49 2.281,0.198 10 false from Engine Stop and Start ECU*1 5.208,5.76 5.667,5.958 0.458,0.198 10 false H10 5.208,5.958 6.583,6.448 1.375,0.49 10 false Telephone Transceiver Assembly 2.208,2.521 3.323,2.719 1.115,0.198 10 false from Battery*2 1.635,4.854 3.417,5.052 1.781,0.198 10 false from IG2 NO. 2 Relay*2 3.958,2.375 4.417,2.573 0.458,0.198 10 false DCM*2 3.615,4.698 4.698,4.906 1.083,0.208 10 false ECU-IG2 NO.3*2 0.25,5.552 2.531,5.75 2.281,0.198 10 false *1: w/ Stop and Start System 0.25,5.969 2.531,6.167 2.281,0.198 10 false *2: w/o Stop and Start System 4,1.833 4.313,2.031 0.313,0.198 10 false *1 4.917,2.25 5.229,2.448 0.313,0.198 10 false *2 4.021,4.167 4.333,4.365 0.313,0.198 10 false *1 4.917,4.583 5.229,4.781 0.313,0.198 10 false *2 5.75,0.552 6.208,0.75 0.458,0.198 10 false CANP 5.75,1.083 6.208,1.281 0.458,0.198 10 false CANN 5.75,4.292 6.208,4.49 0.458,0.198 10 false IG2 5.75,1.948 6.063,2.146 0.313,0.198 10 false +B 5.75,5.354 6.063,5.552 0.313,0.198 10 false E 1.583,0.417 1.896,0.615 0.313,0.198 10 false 3 1.604,0.948 1.917,1.146 0.313,0.198 10 false 14 5.333,0.427 5.646,0.625 0.313,0.198 10 false 25 5.344,0.958 5.656,1.156 0.313,0.198 10 false 26 5.417,1.833 5.573,2.031 0.156,0.198 10 false 1 5.385,4.167 5.885,4.531 0.5,0.365 10 false 19 5.427,5.229 5.802,5.427 0.375,0.198 10 false 20

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for ERA-GLONASS A
for eCall B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY BRANCH WIRE)

B

5.CHECK FOR OPEN IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369145C34
1.5,0.667 1.917,0.917 0.417,0.25 1.958,2.115 2.167,1.417 2.167,1.417 2.333,1.417 true 1.813,2.104 2,1.25 2,1.25 2.167,1.25 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.625,0.719 2,0.927 0.375,0.208 10 false H6 2.219,1.188 2.688,1.406 0.469,0.219 10 false CANP 2.375,1.354 2.844,1.573 0.469,0.219 10 false CANN
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-15 (CANP) - H6-16 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/ Stop and Start System) A
OK (w/o Stop and Start System) B
NG C



A

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369145C35
1.5,0.667 1.917,0.917 0.417,0.25 0.823,2.094 1.073,1.177 1.073,1.177 1.24,1.177 true 0.781,1.917 0.615,1.083 0.615,1.083 0.448,1.083 true 0.719,2.156 0.969,2.906 0.969,2.906 1.135,2.906 true 2.292,1.917 2.542,1 2.542,1 2.708,1 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.625,0.719 2.031,0.917 0.406,0.198 10 false H6 0.24,1.042 0.708,1.26 0.469,0.219 10 false +B 1.302,1.115 1.771,1.333 0.469,0.219 10 false ACC 1.198,2.844 1.667,3.063 0.469,0.219 10 false IG2 2.771,0.948 3.24,1.167 0.469,0.219 10 false E
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-4 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H6-1 (+B) - Body ground Always 10.5 to 16 V
H6-8 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V
Ignition switch off Below 1 V
H6-7 (IG2) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (+B, ACC or IG2 terminal) B
NG (Other terminal) C



A

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369145C35
1.5,0.667 1.917,0.917 0.417,0.25 0.823,2.094 1.073,1.177 1.073,1.177 1.24,1.177 true 0.781,1.917 0.615,1.083 0.615,1.083 0.448,1.083 true 0.719,2.156 0.969,2.906 0.969,2.906 1.135,2.906 true 2.292,1.917 2.542,1 2.542,1 2.708,1 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.625,0.719 2.031,0.917 0.406,0.198 10 false H6 0.24,1.042 0.708,1.26 0.469,0.219 10 false +B 1.302,1.115 1.771,1.333 0.469,0.219 10 false ACC 1.198,2.844 1.667,3.063 0.469,0.219 10 false IG2 2.771,0.948 3.24,1.167 0.469,0.219 10 false E
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-4 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H6-1 (+B) - Body ground Always 11 to 14 V
H6-8 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
H6-7 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FOR OPEN IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E423827C68
1.49,0.271 1.938,0.542 0.448,0.271 1.813,1.771 1.688,1.771 1.688,1.771 1.385,1.229 true 1.76,1.948 1.635,1.948 1.635,1.948 1.26,1.229 true 0.135,0.083 0.313,0.25 0.177,0.167 10 false *a 1.573,0.323 1.99,0.49 0.417,0.167 10 false H10 1.875,1.698 2.458,1.896 0.583,0.198 10 false CANN 1.813,1.885 2.396,2.083 0.583,0.198 10 false CANP
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-25 (CANP) - H10-26 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/ Stop and Start System) A
OK (w/o Stop and Start System) B
NG C



A

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C404434C47
1.5,0.917 2,1.167 0.5,0.25 0.521,1.698 0.698,1.094 0.698,1.094 0.854,1.094 true 1.094,2.583 0.938,2.583 0.938,2.583 0.604,1.875 true 1.385,2.385 1.219,2.385 1.219,2.385 0.729,1.875 true 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.625,0.948 2.083,1.146 0.458,0.198 10 false H10 1.469,2.333 1.708,2.521 0.24,0.188 10 false E 0.958,1.021 1.219,1.198 0.26,0.177 10 false +B 1.156,2.5 1.417,2.677 0.26,0.177 10 false IG2
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-20 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H10-1 (+B) - Body ground Always 10.5 to 16 V
H10-19 (IG2) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (+B, ACC or IG2 terminal) B
NG (Other terminal) C



A

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C404434C47
1.5,0.917 2,1.167 0.5,0.25 0.521,1.698 0.698,1.094 0.698,1.094 0.854,1.094 true 1.094,2.583 0.938,2.583 0.938,2.583 0.604,1.875 true 1.385,2.385 1.219,2.385 1.219,2.385 0.729,1.875 true 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.625,0.948 2.083,1.146 0.458,0.198 10 false H10 1.469,2.333 1.708,2.521 0.24,0.188 10 false E 0.958,1.021 1.219,1.198 0.26,0.177 10 false +B 1.156,2.5 1.417,2.677 0.26,0.177 10 false IG2
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-20 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H10-1 (+B) - Body ground Always 11 to 14 V
H10-19 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR