Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.08
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) D

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  DIAGNOSIS SYSTEM  


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION


a.

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

i.

GTS display and installed systems

HINT:

The names of ECUs and sensors shown on the GTS display may differ from those shown in DTC Table by ECU.


Connected to Code ECU/Sensor Name GTS Display Applicability
- CGW Central gateway ECU (network gateway ECU) - Installed on all vehicles
V Bus DLC3 DLC3 - Installed on all vehicles
Bus 1 F-CAM Forward recognition camera Front Camera Module w/ Pre-collision System
F-MR Millimeter wave radar sensor assembly Front Radar w/ Pre-collision System
CS Clearance warning ECU assembly Clearance Warning (Clearance Sonar) w/ TOYOTA Parking Assist-sensor System
GRS Swing grille actuator assembly Grille Shutter w/ Grille Shutter System
PAC Parking assist ECU Panoramic View Monitor w/ Panoramic View Monitor System
BSM Blind spot monitor sensor LH Blind Spot Monitor Master w/ Blind Spot Monitor System
R-CA Television camera assembly Parking Assist Monitor System / Rear Camera
·

w/ Panoramic View Monitor System

·

w/ Parking Assist Monitor System


Bus 2 S&S Engine stop and start ECU Stop and Go/Start w/ Stop and Start System
TCM Transmission control ECU TCM for CVT
ENG ECM ECM (Engine) Installed on all vehicles
Bus 3 AV Radio and display receiver assembly Display and Navigation (AVN) for Radio and Display Type
DCM Telephone transceiver assembly DCM w/ Telematics System
YGW Bus buffer ECU Accessory Gateway w/ Bus Buffer ECU
Bus 4 OCS Occupant detection ECU Occupant Detection w/ Occupant Classification System
STR Steering sensor Spiral cable (Steering Angle Sensor) Installed on all vehicles
EPS Rack and pinion power steering gear assembly Power Steering (EPS) Installed on all vehicles
BRK Brake actuator assembly (skid control ECU) Skid Control (ABS/VSC/TRAC) Installed on all vehicles
AWD 4WD ECU assembly Four Wheel Drive Control for 4WD/AWD
SRS Airbag sensor assembly Airbag Installed on all vehicles
Bus 5 LITM Headlight ECU sub-assembly LH HL AutoLeveling/AFS/AHS w/ Power Back Door System
DST Position control ECU assembly D-Seat w/ Memory
MB Main body ECU (multiplex network body ECU) Main Body Installed on all vehicles
A/C Air conditioning amplifier assembly Air Conditioning Amplifier Installed on all vehicles
SMT Certification ECU (smart key ECU assembly) Certification (Smart) w/ Entry and Start System
BKD Multiplex network door ECU Back Door w/ Power Back Door System
LITS Headlight ECU sub-assembly RH HL AutoLeveling/AFS/AHS (Sub) Installed on all vehicles
MET Combination meter assembly Combination Meter Installed on all vehicles




Description of "Communication Bus Check" Screen


NOTICE:

The following communication bus check screen is provided only as an example. This screen differs from the actual screen for this vehicle.


HINT:

The ECUs and sensors that are normally connected to the CAN communication system are displayed on the GTS.


a.

Select "Communication Bus Check" on the menu screen of the GTS.

CAN Bus Check
50007
HINT:

If items are not selected correctly in the vehicle specification pop up screen, the name of the CAN junction connector to which the ECUs or sensors are connected may not be displayed on the "Communication Bus Check" screen.



b.

Confirm that the "Communication Bus Check" screen is displayed and the ECUs and sensors that are normally connected to the CAN communication system are displayed.

HINT:
·

Even if an ECU or sensor that is connected to a bus that is monitored by a bus monitoring ECU (gateway function equipped ECU) is not communicating, it will remain displayed on the "Communication Bus Check" screen.

·

When an ECU or sensor that is connected to a bus that is not monitored by a bus monitoring ECU (gateway function equipped ECU) is not displayed on the "Communication Bus Check" screen, it means that it is not communicating.




c.

The default display setting selected on the combo box is ALL. When checking for ECUs or sensors for a specific bus, choose the bus from the drop down list. ALL, each bus, each sub bus and Central Gateway are listed in the drop down list.

C352726C01
3.146,4.833 3.635,4.646 true 0.135,2.75 0.448,2.948 0.313,0.198 10 false *b 3.719,4.531 4.031,4.729 0.313,0.198 10 false *a
*a Combo box *b Background color is red or yellow


Item Detail
Combo box: ALL Displays all ECUs and sensors connected to the central bus and sub buses.
Combo box: Bus Displays ECUs and sensors connected to the selected bus.
Combo box: Sub bus Displays ECUs and sensors connected to the selected sub bus.
Combo box: Central Gateway Displays all ECUs and sensors connected to the central bus.

NOTICE:
·

When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).

·

In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose the CAN communication system, refer to System Diagram.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>SYSTEM DIAGRAM



HINT:

The background color of an ECU or sensor changes according to its connection status as indicated in the following table.

Description of "Communication Bus Check" Screen
Bus Type Background Color Connection Status
Bus White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4

·

No ECUs or sensors are connected to the bus.*5


Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*6

·

No ECUs or sensors are connected to the sub bus.*7



·

Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.

·

*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.

·

*2: the gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.

·

*3: the gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.

·

*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.

·

If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and diagnosis bus (The bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.




d.

Monitor the screen for any ECU or sensor connection status changes for a period of 2 minutes.

HINT:
·

If an open occurs in one of the wires of a CAN branch line, it may interfere with the communication of other ECUs or sensors resulting in an incorrect state being displayed.

·

If the connection status changes intermittently during the inspection, repair the open in the branch line of the ECU or sensor that is not communicating, and then perform Communication Bus Check again.





Description of "Communication Bus Check (Detail)" Screen


NOTICE:

The following communication bus check screen is provided only as an example. This screen differs from the actual screen for this vehicle.


HINT:

The communication error history of ECUs or sensors which have communication error history can be displayed on the "Communication Bus Check (Detail)" screen.


a.

Select "Communication Bus Check" on the menu screen of the GTS.

CAN Bus Check
50007
HINT:

If items are not selected correctly in the vehicle specification pop up screen, the name of the CAN junction connector to which the ECUs or sensors are connected may not be displayed on the "Communication Bus Check" screen.



b.

Select "Detail" on the "Communication Bus Check" screen.

C352727C01
4.521,4.906 4.167,4.583 4.167,4.583 4,4.583 true 3.802,4.49 4.115,4.688 0.313,0.198 10 false *a
*a Communication Bus Check (Detail) - -



c.

Confirm that the "Communication Bus Check (Detail)" screen is displayed and the communication error history of the ECUs or sensors up to present is displayed.

HINT:
·

Lost Communication Time and Lost Communication Trip are only displayed for the central bus.

·

Lost Communication Time and Lost Communication Trip are not displayed for sub buses.




d.

The default display setting selected on the combo box is ALL. When checking for ECUs or sensors for a specific bus, choose the bus from the drop down list. ALL, each bus, each sub bus and Central Gateway are listed in the drop down list.

C352728C01
3.156,4.833 3.719,4.667 true 0.219,1.906 0.531,2.104 0.313,0.198 10 false *b 3.781,4.552 4.094,4.75 0.313,0.198 10 false *a
*a Combo box *b Background color is red


Item Detail
Combo box: ALL Displays all ECUs and sensors connected to the central bus and sub buses.
Combo box: Bus Displays ECUs and sensors connected to the selected bus.
Combo box: Sub bus Displays ECUs and sensors connected to the selected sub bus.
Combo box: Central Gateway Displays all ECUs and sensors connected to the central bus.
Bus Monitoring ECU Displays the gateway function equipped ECU which monitors the selected bus or sub bus.
Current Trip Displays the total number of trips up to now*
Lost Communication Time(s) Displays the longest period of time in seconds that the ECU or sensor connected to the central bus was not communicating.
Lost Communication Trip Displays the trip in which the longest period of time that the ECU or sensor connected to the central bus was not communicating occurred.

*: If the component has been replaced with a new one, the total number of trips after the replacement is displayed.


NOTICE:
·

The Lost Communication Time column displays the longest period of time in seconds that the central gateway ECU (network gateway ECU) detected a communication stop in the respective ECU or sensor.

·

The Lost Communication Trip column displays the trip in which the central gateway ECU (network gateway ECU) detected the longest communication stop in the respective ECU or sensor.

·

When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).

·

In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose CAN communication system, refer to the System Diagram.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>SYSTEM DIAGRAM



HINT:

The background color of an ECU or sensor changes according to its connection status as indicated in the following table.

Description of "Communication Bus Check (Detail)" Screen
Bus Type Background Color Connection Status
Bus White Either of the following:
·

Communication has been normal.

·

Lost Communication Time is below 6 seconds.


Red Lost Communication Time is 6 seconds or more.
Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*1

·

No ECUs or sensors are connected to the bus.*2


Sub bus White Lost Communication Time is displayed as "-".
Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*3

·

No ECUs or sensors are connected to the sub bus.*4



·

If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and diagnosis bus (The bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.

·

Lost Communication Time and Lost Communication Trip are not displayed for sub buses.

·

*1: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*2: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*3: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*4: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.





Communication Bus Check (Communication Malfunction Check)


HINT:

DTCs related to CAN communication are displayed for each ECU on the GTS.


a.

Select "Communication Bus Check" on the menu screen of the GTS.

CAN Bus Check
50007

b.

Select "Communication Malfunction Check" on the "Communication Bus Check" screen.

C352729C01
5.073,4.896 4.917,4.583 4.917,4.583 4.083,4.583 true 3.896,4.49 4.208,4.688 0.313,0.198 10 false *a
*a Communication Malfunction Check - -



c.

Confirm that the "Communication Malfunction Check" screen is displayed and CAN communication DTCs for each ECU are displayed.

HINT:

When there are no CAN communication DTCs stored, no DTCs will be displayed.




How to Use "Communication Bus Check" Screen in Inspection


NOTICE:

The following CAN bus wiring diagram or communication bus check screen is provided only as an example. This wiring diagram or screen differs from the actual one for this vehicle.


HINT:
·

If the CAN communication system is currently malfunctioning, it is recommended to use Communication Bus Check rather than Communication DTCs for determining the suspected area.

·

Turn the ignition switch to ON, or perform the necessary operations to reproduce the problem symptom, select "Communication Bus Check" and wait approximately 2 minutes. Check the communication status of each ECU or sensor on the screen while performing this operation.



a.

If the CAN communication system is currently malfunctioning, determine the suspected area through Communication Bus Check as follows:

Problem Symptoms Table
Problem Symptom Pattern Display on Communication Bus Check Screen Suspected Area
A Almost all of the ECUs and sensors connected to the malfunctioning CAN bus are displayed as not communicating on the "Communication Bus Check" screen.
·

Short between CAN bus lines (CANH and CANL)

·

Short to +B in a CAN bus line (CANH or CANL)

·

Short to ground in a CAN bus line (CANH or CANL)


B ECUs or sensors farther from the central gateway ECU (network gateway ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen. Open in both wires of a main bus line in the central bus
C One ECU or sensor is displayed as not communicating on the "Communication Bus Check" screen.
·

Open in both wires of a branch line connected to an ECU or sensor in the central bus

·

Internal malfunction of an ECU or sensor in the central bus

·

Malfunction in the power supplied to an ECU or sensor in the central bus


D No ECUs or sensors are displayed on the "Communication Bus Check" screen.
·

Internal malfunction of the central gateway ECU (network gateway ECU)

·

Malfunction in the power supplied to the central gateway ECU (network gateway ECU)

·

Open in both wires of the branch line in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))

·

Short between CAN bus lines (CANH and CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))

·

Short to +B in a CAN bus line (CANH or CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))

·

Short to ground in a CAN bus line (CANH or CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))


E One ECU or sensor is displayed as not communicating in multiple buses on the "Communication Bus Check" screen.
·

Internal malfunction of an ECU or sensor connected to multiple buses

·

Malfunction in the power supplied to an ECU or sensor connected to multiple buses


F Some ECUs or sensors are displayed as not communicating in the central bus and other ECUs or sensors are displayed as not communicating in a sub bus.
·

Open in a wire of a branch line connected to an ECU or sensor in the central bus

·

Internal malfunction of an ECU or sensor in the central bus


G A gateway function equipped ECU is displayed as not communicating in the central bus and ECUs and sensors connected to its respective sub bus are not displayed.
·

Open in both wires of a branch line connected to a gateway function equipped ECU

·

Internal malfunction of a gateway function equipped ECU

·

Malfunction in the power supplied to a gateway function equipped ECU


H One ECU or sensor is displayed as not communicating in a sub bus on the "Communication Bus Check" screen.
·

Open in both wires of a branch line connected to an ECU or sensor in a sub bus

·

Internal malfunction of an ECU or sensor in a sub bus

·

Malfunction in the power supplied to an ECU or sensor in a sub bus


I ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen. Open in both wires of a main bus line in a sub bus


b.

Problem Symptom Pattern A

Details of Malfunction
·

Short between CAN bus lines (CANH and CANL) in Bus 2

·

Short to +B in a CAN bus line (CANH or CANL) in Bus 2

·

Short to ground in a CAN bus line (CANH or CANL) in Bus 2



C352730C01
2.073,0.281 2.677,0.479 0.604,0.198 10 false F-MGC 3.75,0.281 4.208,0.479 0.458,0.198 10 false HVB 1.927,0.844 2.958,1.073 1.031,0.229 10 false CAN J/C 1 4.313,0.281 5.021,0.542 0.708,0.26 10 false R-MGC 2.458,1.438 2.917,1.635 0.458,0.198 10 false BRK 1.854,2.677 2.313,2.875 0.458,0.198 10 false MB 3.063,4.073 3.583,4.281 0.521,0.208 10 false MIR-R 4.99,4.083 5.521,4.313 0.531,0.229 10 false MIR-L 6.417,0.844 6.875,1.042 0.458,0.198 10 false ENG 5.729,2.01 6.188,2.208 0.458,0.198 10 false SRS 1.875,1.438 2.333,1.635 0.458,0.198 10 false HV 6.469,3.458 6.76,3.802 0.292,0.344 10 false ST 1.531,4.125 1.99,4.323 0.458,0.198 10 false DLC3 3.74,2.615 4.198,2.813 0.458,0.198 10 false EPS 4.385,2.625 4.844,2.823 0.458,0.198 10 false STR 5.771,0.188 6.229,0.385 0.458,0.198 10 false : *e 0.448,2.25 0.906,2.448 0.458,0.198 10 false CGW 3.865,0.844 4.896,1.073 1.031,0.229 10 false CAN J/C 2 1.938,2.021 2.969,2.25 1.031,0.229 10 false CAN J/C 3 3.844,2.01 4.875,2.24 1.031,0.229 10 false CAN J/C 4 2.917,3.458 3.948,3.688 1.031,0.229 10 false CAN J/C 5 4.802,3.448 5.833,3.677 1.031,0.229 10 false CAN J/C 6 1,0.625 1.458,0.823 0.458,0.198 10 false *a 1.01,1.813 1.469,2.01 0.458,0.198 10 false *b 1.01,3.896 1.469,4.094 0.458,0.198 10 false *d 1.688,3.073 2.146,3.271 0.458,0.198 10 false *c 0.438,5.51 0.896,5.708 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:
·

Due to the malfunction, almost all of the ECUs and sensors connected to Bus 2 will be displayed as not communicating and their background color will be red.

·

The malfunction in Bus 2 will not affect the other buses.

·

The malfunctioning part can be determined by inspecting for an open in the main bus line, a short between bus lines or a short to +B or ground.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.



Details of Malfunction
·

Short between CAN bus lines (CANH and CANL) in Bus 4

·

Short to +B in a CAN bus line (CANH or CANL) in Bus 4

·

Short to ground in a CAN bus line (CANH or CANL) in Bus 4



C352731C01
2.073,0.281 2.604,0.521 0.531,0.24 10 false F-MGC 3.74,0.281 4.198,0.479 0.458,0.198 10 false HVB 4.302,0.281 4.906,0.563 0.604,0.281 10 false R-MGC 6.406,0.854 6.865,1.052 0.458,0.198 10 false ENG 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 2.469,1.448 2.927,1.646 0.458,0.198 10 false BRK 5.729,2.01 6.188,2.208 0.458,0.198 10 false SRS 4.396,2.625 4.854,2.823 0.458,0.198 10 false STR 3.75,2.625 4.208,2.823 0.458,0.198 10 false EPS 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 6.469,3.458 6.927,3.656 0.458,0.198 10 false ST 4.99,4.073 5.479,4.271 0.49,0.198 10 false MIR-L 3.073,4.083 3.594,4.354 0.521,0.271 10 false MIR-R 1.542,4.135 2,4.333 0.458,0.198 10 false DLC3 1.958,0.854 2.708,1.115 0.75,0.26 10 false CAN J/C 1 3.875,0.844 4.625,1.104 0.75,0.26 10 false CAN J/C 2 1.948,2.031 2.698,2.292 0.75,0.26 10 false CAN J/C 3 3.865,2.021 4.615,2.281 0.75,0.26 10 false CAN J/C 4 2.917,3.458 3.667,3.719 0.75,0.26 10 false CAN J/C 5 4.813,3.458 5.563,3.719 0.75,0.26 10 false CAN J/C 6 5.625,0.188 6.083,0.385 0.458,0.198 10 false : *e 1,0.635 1.458,0.833 0.458,0.198 10 false *a 1.01,3.906 1.469,4.104 0.458,0.198 10 false *d 1.667,3.104 2.125,3.302 0.458,0.198 10 false *c 1,1.833 1.458,2.031 0.458,0.198 10 false *b 0.479,6.427 0.938,6.625 0.458,0.198 10 false *f 0.479,7.198 0.938,7.396 0.458,0.198 10 false *g 0.458,2.24 0.917,2.438 0.458,0.198 10 false CGW
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red
*g Not displayed - -


HINT:
·

Due to the malfunction, almost all of the ECUs and sensors connected to Bus 4 will be displayed as not communicating and their background color will be red.

·

The malfunction will not affect the other buses of the central bus. However, the sub bus connected to Bus 4 is likely to be affected. the gateway function equipped ECU connected to Bus 4 will not communicate and consequently the sub bus and its respective ECUs or sensors monitored by the gateway function equipped ECU (sub bus monitoring ECU) will not be displayed, indicating that the gateway function equipped ECU is not communicating with the central gateway ECU (network gateway ECU).

·

The malfunctioning part can be determined by inspecting for an open in the main bus line, a short between bus lines or a short to +B or ground.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.




c.

Problem Symptom Pattern B

Details of Malfunction Open in both wires of the main bus line between the CGW and No. 1 CAN junction connector in Bus 2

C352732C01
6.417,0.844 6.875,1.042 0.458,0.198 10 false ENG 2.458,1.448 2.917,1.646 0.458,0.198 10 false BRK 2.063,0.292 2.583,0.5 0.521,0.208 10 false F-MGC 1.865,1.458 2.323,1.656 0.458,0.198 10 false HV 4.302,0.292 4.885,0.531 0.583,0.24 10 false R-MGC 3.76,0.292 4.219,0.49 0.458,0.198 10 false HVB 1.854,2.698 2.313,2.896 0.458,0.198 10 false MB 1.531,4.135 1.99,4.333 0.458,0.198 10 false DLC3 6.469,3.469 6.927,3.667 0.458,0.198 10 false ST 3.073,4.073 3.583,4.302 0.51,0.229 10 false MIR-R 1.938,0.854 2.885,1.052 0.948,0.198 10 false CAN J/C 1 4.99,4.094 5.49,4.313 0.5,0.219 10 false MIR-L 3.74,2.625 4.198,2.823 0.458,0.198 10 false EPS 5.708,2.021 6.167,2.219 0.458,0.198 10 false SRS 4.406,2.625 4.865,2.823 0.458,0.198 10 false STR 0.458,2.219 0.917,2.417 0.458,0.198 10 false CGW 1,0.635 1.458,0.833 0.458,0.198 10 false *a 3.865,0.844 4.813,1.042 0.948,0.198 10 false CAN J/C 2 1.948,2.031 2.896,2.229 0.948,0.198 10 false CAN J/C 3 2.896,3.469 3.844,3.667 0.948,0.198 10 false CAN J/C 5 3.844,2.021 4.792,2.219 0.948,0.198 10 false CAN J/C 4 4.792,3.458 5.74,3.656 0.948,0.198 10 false CAN J/C 6 1.021,1.844 1.479,2.042 0.458,0.198 10 false *b 1.667,3.125 2.125,3.323 0.458,0.198 10 false *c 1,3.938 1.458,4.135 0.458,0.198 10 false *d 5.583,0.125 6.042,0.323 0.458,0.198 10 false : *e 0.344,5.448 0.802,5.646 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:
·

Due to the malfunction, almost all of the ECUs and sensors connected to Bus 2 will be displayed as not communicating and their background color will be red.

·

The malfunction in Bus 2 will not affect the other buses.

·

The malfunctioning part can be determined by inspecting for an open in the main bus line.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.



Details of Malfunction Open in both wires of the main bus line between the No. 1 CAN junction connector and No. 2 CAN junction connector in Bus 2

C352733C01
0.448,2.208 0.906,2.406 0.458,0.198 10 false CGW 2.063,0.281 2.656,0.521 0.594,0.24 10 false F-MGC 3.74,0.281 4.198,0.479 0.458,0.198 10 false HVB 4.302,0.281 4.844,0.542 0.542,0.26 10 false R-MGC 6.417,0.854 6.875,1.052 0.458,0.198 10 false ENG 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 2.458,1.448 2.917,1.646 0.458,0.198 10 false BRK 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 1.542,4.125 2,4.323 0.458,0.198 10 false DLC3 3.063,4.073 3.573,4.281 0.51,0.208 10 false MIR-R 5,4.073 5.458,4.271 0.458,0.198 10 false MIR-L 6.448,3.458 6.906,3.656 0.458,0.198 10 false ST 5.74,2.01 6.198,2.208 0.458,0.198 10 false SRS 4.396,2.615 4.854,2.813 0.458,0.198 10 false STR 3.74,2.625 4.198,2.823 0.458,0.198 10 false EPS 1.948,0.854 2.844,1.042 0.896,0.188 10 false CAN J/C 1 3.865,0.844 4.76,1.031 0.896,0.188 10 false CAN J/C 2 1.927,2.01 2.823,2.198 0.896,0.188 10 false CAN J/C 3 3.865,2.01 4.76,2.198 0.896,0.188 10 false CAN J/C 4 2.927,3.458 3.823,3.646 0.896,0.188 10 false CAN J/C 5 4.792,3.458 5.688,3.646 0.896,0.188 10 false CAN J/C 6 5.573,0.188 6.031,0.385 0.458,0.198 10 false : *e 1,0.625 1.458,0.823 0.458,0.198 10 false *a 1,1.823 1.458,2.021 0.458,0.198 10 false *b 1.677,3.083 2.135,3.281 0.458,0.198 10 false *c 1.031,3.896 1.49,4.094 0.458,0.198 10 false *d 0.49,5.729 0.948,5.927 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:
·

Due to the malfunction, ECUs or sensors farther from the CGW than the open in the wires will be displayed as not communicating and their background color will be red.

·

The malfunction in Bus 2 will not affect the other buses.

·

The malfunctioning part can be determined by inspecting for an open in the main bus line.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.



Details of Malfunction Open in both wires of the main bus line between the No. 2 CAN junction connector and ENG in Bus 2

C352734C01
2.667,6.115 2.583,4.781 2.583,4.781 2.333,4.781 true 5,6 5.167,4.667 5.167,4.667 5.417,4.667 true 0.448,2.188 0.906,2.385 0.458,0.198 10 false CGW 2.063,0.292 2.615,0.521 0.552,0.229 10 false F-MGC 3.75,0.292 4.208,0.49 0.458,0.198 10 false HVB 4.302,0.292 4.813,0.531 0.51,0.24 10 false R-MGC 6.406,0.854 6.865,1.052 0.458,0.198 10 false ENG 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 2.469,1.448 2.927,1.646 0.458,0.198 10 false BRK 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 5.74,2.021 6.198,2.219 0.458,0.198 10 false SRS 4.396,2.635 4.854,2.833 0.458,0.198 10 false STR 3.75,2.635 4.208,2.833 0.458,0.198 10 false EPS 1.521,4.125 1.979,4.323 0.458,0.198 10 false DLC3 3.073,4.094 3.635,4.333 0.563,0.24 10 false MIR-R 5,4.094 5.521,4.313 0.521,0.219 10 false MIR-L 6.458,3.469 6.917,3.667 0.458,0.198 10 false ST 1.938,0.854 2.719,1.052 0.781,0.198 10 false CAN J/C 1 3.865,0.854 4.646,1.052 0.781,0.198 10 false CAN J/C 2 1.979,2.021 2.76,2.219 0.781,0.198 10 false CAN J/C 3 3.865,2.021 4.646,2.219 0.781,0.198 10 false CAN J/C 4 2.927,3.469 3.708,3.667 0.781,0.198 10 false CAN J/C 5 4.833,3.458 5.615,3.656 0.781,0.198 10 false CAN J/C 6 1.01,0.635 1.469,0.833 0.458,0.198 10 false *a 1.01,1.802 1.469,2 0.458,0.198 10 false *b 1.656,3.083 2.115,3.281 0.458,0.198 10 false *c 1.021,3.896 1.479,4.094 0.458,0.198 10 false *d 5.75,0.125 6.208,0.323 0.458,0.198 10 false : *e 0.115,4.885 0.573,5.083 0.458,0.198 10 false *g 3.677,4.896 4.135,5.094 0.458,0.198 10 false *h 2.156,4.708 2.615,4.906 0.458,0.198 10 false *f 5.5,4.594 5.958,4.792 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red
*g Pattern 1 *h Pattern 2


HINT:
·

Even when the same part of the main bus line is open, depending on internal electrical noise which changes according to the position of the open in the line, the information displayed on the "Communication Bus Check" screen may differ.

·

In pattern 2, the information displayed may be the same as when there is an open in both wires in the main bus line between the No. 1 CAN junction connector and No. 2 CAN junction connector, which may make it difficult to determine the malfunctioning part.

·

The malfunction in Bus 2 will not affect the other buses.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.




d.

Problem Symptom Pattern C

Details of Malfunction Open in both wires of the branch line connected to F-MGC in Bus 2

C352735C01
0.458,2.146 0.917,2.344 0.458,0.198 10 false CGW 2.063,0.292 2.615,0.51 0.552,0.219 10 false F-MGC 3.75,0.281 4.208,0.479 0.458,0.198 10 false HVB 4.302,0.281 4.875,0.552 0.573,0.271 10 false R-MGC 6.406,0.844 6.865,1.042 0.458,0.198 10 false ENG 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 2.458,1.448 2.917,1.646 0.458,0.198 10 false BRK 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 1.531,4.125 1.99,4.323 0.458,0.198 10 false DLC3 3.073,4.073 3.646,4.292 0.573,0.219 10 false MIR-R 3.75,2.635 4.208,2.833 0.458,0.198 10 false EPS 4.406,2.625 4.865,2.823 0.458,0.198 10 false STR 5.729,2.021 6.188,2.219 0.458,0.198 10 false SRS 6.469,3.469 6.927,3.667 0.458,0.198 10 false ST 5,4.073 5.469,4.302 0.469,0.229 10 false MIR-L 1.948,0.844 2.906,1.031 0.958,0.188 10 false CAN J/C 1 3.875,0.844 4.833,1.031 0.958,0.188 10 false CAN J/C 2 1.958,2.021 2.917,2.208 0.958,0.188 10 false CAN J/C 3 3.906,2.021 4.865,2.208 0.958,0.188 10 false CAN J/C 4 2.917,3.458 3.875,3.646 0.958,0.188 10 false CAN J/C 5 4.802,3.458 5.76,3.646 0.958,0.188 10 false CAN J/C 6 1,0.635 1.458,0.833 0.458,0.198 10 false *a 1,1.813 1.458,2.01 0.458,0.198 10 false *b 1.698,3.083 2.156,3.281 0.458,0.198 10 false *c 1,3.917 1.458,4.115 0.458,0.198 10 false *d 5.469,0.167 5.927,0.365 0.458,0.198 10 false : *e 0.302,5.042 0.76,5.24 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:

The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor. In this example, the background color of the malfunctioning ECU or sensor will be red.


Details of Malfunction
·

Internal malfunction of F-MGC in Bus 2

·

Malfunction in the power supplied to F-MGC in Bus 2



C352736C01
0.438,2.219 0.896,2.417 0.458,0.198 10 false CGW 2.063,0.292 2.656,0.542 0.594,0.25 10 false F-MGC 3.75,0.292 4.208,0.49 0.458,0.198 10 false HVB 4.313,0.302 4.875,0.552 0.563,0.25 10 false R-MGC 6.417,0.865 6.875,1.063 0.458,0.198 10 false ENG 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 2.469,1.458 2.927,1.656 0.458,0.198 10 false BRK 1.854,2.698 2.313,2.896 0.458,0.198 10 false MB 3.75,2.625 4.208,2.823 0.458,0.198 10 false EPS 4.406,2.625 4.865,2.823 0.458,0.198 10 false STR 5.729,2.031 6.188,2.229 0.458,0.198 10 false SRS 1.531,4.125 1.99,4.323 0.458,0.198 10 false DLC3 3.073,4.094 3.573,4.344 0.5,0.25 10 false MIR-R 5,4.083 5.531,4.323 0.531,0.24 10 false MIR-L 6.458,3.458 6.917,3.656 0.458,0.198 10 false ST 1.938,0.854 2.771,1.052 0.833,0.198 10 false CAN J/C 1 3.865,0.854 4.698,1.052 0.833,0.198 10 false CAN J/C 2 1.927,2.021 2.76,2.219 0.833,0.198 10 false CAN J/C 3 3.885,2.031 4.719,2.229 0.833,0.198 10 false CAN J/C 4 2.917,3.469 3.75,3.667 0.833,0.198 10 false CAN J/C 5 4.813,3.458 5.646,3.656 0.833,0.198 10 false CAN J/C 6 1,0.625 1.458,0.823 0.458,0.198 10 false *a 1.01,1.833 1.469,2.031 0.458,0.198 10 false *b 1.698,3.104 2.156,3.302 0.458,0.198 10 false *c 1.01,3.906 1.469,4.104 0.458,0.198 10 false *d 5.823,0.229 6.281,0.427 0.458,0.198 10 false : *e 0.313,5.135 0.771,5.333 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:

The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor. In this example, the background color of the malfunctioning ECU or sensor will be red.


Details of Malfunction Open in both wires of the branch line connected to ENG in Bus 4

C352737C01
0.438,2.313 0.896,2.51 0.458,0.198 10 false CGW 2.063,0.281 2.625,0.521 0.563,0.24 10 false F-MGC 3.74,0.281 4.198,0.479 0.458,0.198 10 false HVB 4.313,0.281 4.865,0.521 0.552,0.24 10 false R-MGC 6.417,0.854 6.875,1.052 0.458,0.198 10 false ENG 1.865,1.438 2.323,1.635 0.458,0.198 10 false HV 2.458,1.448 2.917,1.646 0.458,0.198 10 false BRK 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 1.531,4.115 1.99,4.313 0.458,0.198 10 false DLC3 3.063,4.073 3.604,4.302 0.542,0.229 10 false MIR-R 4.99,4.073 5.521,4.292 0.531,0.219 10 false MIR-L 6.469,3.458 6.927,3.656 0.458,0.198 10 false ST 5.729,2.021 6.188,2.219 0.458,0.198 10 false SRS 4.406,2.615 4.865,2.813 0.458,0.198 10 false STR 3.74,2.625 4.198,2.823 0.458,0.198 10 false EPS 1.917,0.844 2.698,1.052 0.781,0.208 10 false CAN J/C 1 3.885,0.844 4.667,1.052 0.781,0.208 10 false CAN J/C 2 1.958,2 2.74,2.208 0.781,0.208 10 false CAN J/C 3 3.896,2.01 4.677,2.219 0.781,0.208 10 false CAN J/C 4 2.906,3.458 3.688,3.667 0.781,0.208 10 false CAN J/C 5 4.823,3.438 5.604,3.646 0.781,0.208 10 false CAN J/C 6 1,0.625 1.302,0.854 0.302,0.229 10 false *a 0.99,1.813 1.292,2.042 0.302,0.229 10 false *b 1.677,3.073 1.979,3.302 0.302,0.229 10 false *c 1,3.896 1.302,4.125 0.302,0.229 10 false *d 5.667,0.177 5.969,0.406 0.302,0.229 10 false : *e 0.25,5.948 0.552,6.177 0.302,0.229 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:
·

The malfunction in Bus 4 will not affect the other buses.

·

Due to the malfunction, although ENG is communicating normally with CGW via Bus 2, it is not communicating with CGW via Bus 4. Consequently, it will be displayed as not communicating in Bus 4.




e.

Problem Symptom Pattern D

Details of Malfunction
·

Internal malfunction of the CGW

·

Malfunction in the power supplied to the CGW



C352738C01
0.448,2.198 0.906,2.396 0.458,0.198 10 false CGW 2.063,0.281 2.594,0.51 0.531,0.229 10 false F-MGC 3.75,0.281 4.208,0.479 0.458,0.198 10 false HVB 4.302,0.281 4.844,0.49 0.542,0.208 10 false R-MGC 6.417,0.854 6.875,1.052 0.458,0.198 10 false ENG 2.458,1.448 2.917,1.646 0.458,0.198 10 false BRK 1.875,1.448 2.333,1.646 0.458,0.198 10 false HV 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 3.063,4.073 3.573,4.292 0.51,0.219 10 false MIR-R 4.99,4.073 5.5,4.292 0.51,0.219 10 false MIR-L 6.49,3.458 6.948,3.656 0.458,0.198 10 false ST 1.531,4.135 1.99,4.333 0.458,0.198 10 false DLC3 3.74,2.625 4.198,2.823 0.458,0.198 10 false EPS 4.396,2.625 4.854,2.823 0.458,0.198 10 false STR 5.729,2.021 6.188,2.219 0.458,0.198 10 false SRS 1.938,0.844 2.813,1.042 0.875,0.198 10 false CAN J/C 1 1.073,0.635 1.531,0.833 0.458,0.198 10 false *a 3.854,0.844 4.729,1.042 0.875,0.198 10 false CAN J/C 2 1.917,2 2.792,2.198 0.875,0.198 10 false CAN J/C 3 3.896,2.01 4.771,2.208 0.875,0.198 10 false CAN J/C 4 2.938,3.448 3.813,3.646 0.875,0.198 10 false CAN J/C 5 4.833,3.438 5.708,3.635 0.875,0.198 10 false CAN J/C 6 1.083,1.833 1.542,2.031 0.458,0.198 10 false *b 1.708,3.052 2.167,3.25 0.458,0.198 10 false *c 1.083,3.938 1.542,4.135 0.458,0.198 10 false *d 5.792,0.229 6.25,0.427 0.458,0.198 10 false : *e 0.396,6.354 0.854,6.552 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Not displayed


HINT:

When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.


Details of Malfunction Open in both wires of the branch lines in the diagnosis bus

C352739C01
0.448,2.219 0.906,2.417 0.458,0.198 10 false CGW 2.063,0.292 2.635,0.5 0.573,0.208 10 false F-MGC 3.75,0.292 4.208,0.49 0.458,0.198 10 false HVB 4.302,0.292 4.969,0.479 0.667,0.188 10 false R-MGC 6.417,0.865 6.875,1.063 0.458,0.198 10 false ENG 1.875,1.448 2.333,1.646 0.458,0.198 10 false HV 2.469,1.448 2.927,1.646 0.458,0.198 10 false BRK 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 3.75,2.635 4.208,2.833 0.458,0.198 10 false EPS 4.396,2.635 4.854,2.833 0.458,0.198 10 false STR 5.729,2.031 6.188,2.229 0.458,0.198 10 false SRS 6.469,3.479 6.927,3.677 0.458,0.198 10 false ST 5,4.083 5.51,4.333 0.51,0.25 10 false MIR-L 3.073,4.094 3.583,4.333 0.51,0.24 10 false MIR-R 1.531,4.135 1.99,4.333 0.458,0.198 10 false DLC3 1.938,0.854 2.708,1.042 0.771,0.188 10 false CAN J/C 1 3.885,0.854 4.656,1.042 0.771,0.188 10 false CAN J/C 2 1.969,2.031 2.74,2.219 0.771,0.188 10 false CAN J/C 3 3.896,2.031 4.667,2.219 0.771,0.188 10 false CAN J/C 4 2.927,3.469 3.698,3.656 0.771,0.188 10 false CAN J/C 5 4.844,3.469 5.615,3.656 0.771,0.188 10 false CAN J/C 6 0.99,0.656 1.448,0.854 0.458,0.198 10 false *a 1,1.844 1.458,2.042 0.458,0.198 10 false *b 1.708,3.073 2.167,3.271 0.458,0.198 10 false *c 1.01,3.917 1.469,4.115 0.458,0.198 10 false *d 5.667,0.188 6.125,0.385 0.458,0.198 10 false : *e 0.292,6.219 0.75,6.417 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Not displayed


HINT:

When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.



f.

Problem Symptom Pattern E

Details of Malfunction
·

Internal malfunction of BRK

·

Malfunction in the power supplied to BRK



C352740C02
0.448,2.208 0.906,2.406 0.458,0.198 10 false CGW 2.063,0.281 2.615,0.521 0.552,0.24 10 false F-MGC 3.76,0.281 4.219,0.479 0.458,0.198 10 false HVB 4.302,0.281 4.865,0.542 0.563,0.26 10 false R-MGC 6.417,0.854 6.875,1.052 0.458,0.198 10 false ENG 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 2.51,1.448 2.969,1.646 0.458,0.198 10 false BRK 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 3.74,2.625 4.198,2.823 0.458,0.198 10 false EPS 4.396,2.625 4.854,2.823 0.458,0.198 10 false STR 5.74,2.021 6.198,2.219 0.458,0.198 10 false SRS 6.458,3.469 6.917,3.667 0.458,0.198 10 false ST 4.99,4.083 5.5,4.292 0.51,0.208 10 false MIR-L 3.063,4.083 3.552,4.323 0.49,0.24 10 false MIR-R 1.521,4.115 1.979,4.313 0.458,0.198 10 false DLC3 1.958,0.854 2.802,1.052 0.844,0.198 10 false CAN J/C 1 0.99,0.646 1.448,0.844 0.458,0.198 10 false *a 1,1.823 1.458,2.021 0.458,0.198 10 false *b 1.688,3.083 2.146,3.281 0.458,0.198 10 false *c 1.021,3.917 1.479,4.115 0.458,0.198 10 false *d 5.823,0.146 6.281,0.344 0.458,0.198 10 false : *e 0.167,5.177 0.625,5.375 0.458,0.198 10 false *f 0.177,6.854 0.635,7.052 0.458,0.198 10 false *f 3.896,0.844 4.74,1.042 0.844,0.198 10 false CAN J/C 2 1.958,2.021 2.802,2.219 0.844,0.198 10 false CAN J/C 3 3.906,2.031 4.75,2.229 0.844,0.198 10 false CAN J/C 4 2.917,3.458 3.76,3.656 0.844,0.198 10 false CAN J/C 5 4.792,3.448 5.635,3.646 0.844,0.198 10 false CAN J/C 6
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:

The information displayed on the "Communication Bus Check" screen will be the same for an internal malfunction of an ECU or sensor, or a malfunction in the power supplied to an ECU or sensor.

Due to the malfunction, BRK is not communicating with the CGW via both Bus 2 and Bus 4. Consequently, the background color of BRK will be red for both Bus 2 and Bus 4.



g.

Problem Symptom Pattern F

Details of Malfunction
·

Open in a wire of the branch line connected to HV in Bus 4

·

Internal malfunction of HV in Bus 4



C352935C02
0.448,2.167 0.906,2.365 0.458,0.198 10 false CGW 2.063,0.281 2.625,0.521 0.563,0.24 10 false F-MGC 1.865,1.417 2.323,1.615 0.458,0.198 10 false HV 2.469,1.417 2.927,1.615 0.458,0.198 10 false BRK 3.74,0.281 4.198,0.479 0.458,0.198 10 false HVB 4.302,0.281 4.896,0.542 0.594,0.26 10 false R-MGC 6.417,0.854 6.875,1.052 0.458,0.198 10 false ENG 6.469,3.458 6.927,3.656 0.458,0.198 10 false ST 5.74,2.021 6.198,2.219 0.458,0.198 10 false SRS 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 1.531,4.125 1.99,4.323 0.458,0.198 10 false DLC3 3.073,4.083 3.552,4.302 0.479,0.219 10 false MIR-R 3.75,2.625 4.208,2.823 0.458,0.198 10 false EPS 4.396,2.615 4.854,2.813 0.458,0.198 10 false STR 4.99,4.083 5.448,4.281 0.458,0.198 10 false MIR-L 1.948,0.833 2.813,1.031 0.865,0.198 10 false CAN J/C 1 1.01,0.656 1.469,0.854 0.458,0.198 10 false *a 1,1.823 1.458,2.021 0.458,0.198 10 false *b 1.708,3.052 2.167,3.25 0.458,0.198 10 false *c 1.031,3.917 1.49,4.115 0.458,0.198 10 false *d 0.229,5.969 0.688,6.167 0.458,0.198 10 false *f 0.198,6.229 0.656,6.427 0.458,0.198 10 false *g 0.24,7.219 0.698,7.417 0.458,0.198 10 false *h 5.604,0.156 6.063,0.354 0.458,0.198 10 false : *e 3.854,0.844 4.719,1.042 0.865,0.198 10 false CAN J/C 2 1.938,2.01 2.802,2.208 0.865,0.198 10 false CAN J/C 3 3.885,2.021 4.75,2.219 0.865,0.198 10 false CAN J/C 4 2.906,3.458 3.771,3.656 0.865,0.198 10 false CAN J/C 5 4.813,3.458 5.677,3.656 0.865,0.198 10 false CAN J/C 6
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red
*g Background color intermittently becomes yellow or red *h Not displayed or background color is yellow or red


HINT:
·

In the "Communication Bus check" screen shown in the illustration, electrical noise in the CAN bus caused by an open in a wire in the branch line connected to HV interferes with the communication of MB causing unstable communication. Also, since MB is a gateway function equipped ECU, communication of ECUs connected to its respective sub bus will also be unstable.

·

In the "Communication Bus Check" screen shown in the illustration, because the background color of HV is red, it is suspected that HV is the most likely cause of the malfunction. Therefore, it is suspected that HV is not communicating.




h.

Problem Symptom Pattern G

Details of Malfunction
·

Open in both wires of the branch line connected to MB in Bus 4

·

Internal malfunction of MB in Bus 4

·

Malfunction in the power supplied to MB in Bus 4



C352936C01
0.458,2.177 0.917,2.375 0.458,0.198 10 false CGW 2.063,0.292 2.656,0.531 0.594,0.24 10 false F-MGC 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 2.458,1.438 2.917,1.635 0.458,0.198 10 false BRK 3.75,0.292 4.208,0.49 0.458,0.198 10 false HVB 4.302,0.292 4.833,0.51 0.531,0.219 10 false R-MGC 6.417,0.844 6.875,1.042 0.458,0.198 10 false ENG 5.729,2.021 6.188,2.219 0.458,0.198 10 false SRS 4.385,2.615 4.844,2.813 0.458,0.198 10 false STR 3.75,2.625 4.208,2.823 0.458,0.198 10 false EPS 1.854,2.667 2.313,2.865 0.458,0.198 10 false MB 1.521,4.115 1.979,4.313 0.458,0.198 10 false DLC3 3.063,4.073 3.563,4.323 0.5,0.25 10 false MIR-R 4.99,4.073 5.479,4.271 0.49,0.198 10 false MIR-L 6.458,3.458 6.917,3.656 0.458,0.198 10 false ST 1.927,0.844 2.708,1.052 0.781,0.208 10 false CAN J/C 1 1.01,0.625 1.469,0.823 0.458,0.198 10 false *a 3.875,0.844 4.656,1.052 0.781,0.208 10 false CAN J/C 2 1.948,2.01 2.729,2.219 0.781,0.208 10 false CAN J/C 3 3.875,2.01 4.656,2.219 0.781,0.208 10 false CAN J/C 4 2.917,3.458 3.698,3.667 0.781,0.208 10 false CAN J/C 5 4.823,3.448 5.604,3.656 0.781,0.208 10 false CAN J/C 6 1,1.813 1.458,2.01 0.458,0.198 10 false *b 1,3.927 1.458,4.125 0.458,0.198 10 false *d 1.688,3.052 2.146,3.25 0.458,0.198 10 false *c 0.427,6.271 0.885,6.469 0.458,0.198 10 false *f 5.771,0.125 6.229,0.323 0.458,0.198 10 false : *e 0.427,7.135 0.885,7.333 0.458,0.198 10 false *g
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red
*g Not displayed - -


HINT:
·

If there is a communication malfunction in a gateway function equipped ECU, ECUs connected to its respective sub bus will also be affected and will not be displayed.

·

In the "Communication Bus Check" screen shown in the illustration, MB is a gateway function equipped ECU. Therefore, MB is suspected as not communicating.




i.

Problem Symptoms Pattern H

Details of Malfunction
·

Internal malfunction of MIR-L in the sub bus

·

Malfunction in the power supplied to MIR-L in the sub bus



C352937C01
0.448,2.198 0.906,2.396 0.458,0.198 10 false CGW 2.063,0.302 2.656,0.542 0.594,0.24 10 false F-MGC 3.74,0.292 4.198,0.49 0.458,0.198 10 false HVB 4.302,0.292 4.885,0.563 0.583,0.271 10 false R-MGC 1.865,1.458 2.323,1.656 0.458,0.198 10 false HV 2.469,1.448 2.927,1.646 0.458,0.198 10 false BRK 6.417,0.865 6.875,1.063 0.458,0.198 10 false ENG 1.854,2.698 2.313,2.896 0.458,0.198 10 false MB 3.75,2.625 4.208,2.823 0.458,0.198 10 false EPS 4.406,2.625 4.865,2.823 0.458,0.198 10 false STR 5.74,2.031 6.198,2.229 0.458,0.198 10 false SRS 3.073,4.083 3.646,4.354 0.573,0.271 10 false MIR-R 1.542,4.125 2,4.323 0.458,0.198 10 false DLC3 4.99,4.083 5.479,4.292 0.49,0.208 10 false MIR-L 6.479,3.479 6.938,3.677 0.458,0.198 10 false ST 1.948,0.854 2.75,1.021 0.802,0.167 10 false CAN J/C 1 0.99,0.646 1.448,0.844 0.458,0.198 10 false *a 1,1.823 1.458,2.021 0.458,0.198 10 false *b 1.688,3.083 2.146,3.281 0.458,0.198 10 false *c 1,3.927 1.458,4.125 0.458,0.198 10 false *d 5.698,0.177 6.156,0.375 0.458,0.198 10 false : *e 0.24,7.313 0.698,7.51 0.458,0.198 10 false *f 3.885,0.854 4.688,1.021 0.802,0.167 10 false CAN J/C 2 1.958,2.031 2.76,2.198 0.802,0.167 10 false CAN J/C 3 4.813,3.458 5.615,3.625 0.802,0.167 10 false CAN J/C 6 3.875,2.031 4.677,2.198 0.802,0.167 10 false CAN J/C 4 2.875,3.458 3.677,3.625 0.802,0.167 10 false CAN J/C 5
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:
·

The malfunction in the sub bus will not affect the other buses.

·

When a gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus and there is a communication malfunction in one of the ECUs or sensors, the background color of the ECU or sensor will change to red and the ECU or sensor will remain displayed.

·

The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor.



Details of Malfunction Open in both wires of the branch line connected to MIR-L in the sub bus

C353622C01
0.448,2.198 0.906,2.396 0.458,0.198 10 false CGW 1.021,0.646 1.479,0.844 0.458,0.198 10 false *a 1.021,1.844 1.479,2.042 0.458,0.198 10 false *b 1.656,3.094 2.115,3.292 0.458,0.198 10 false *c 1.042,3.969 1.5,4.167 0.458,0.198 10 false *d 5.604,0.167 6.063,0.365 0.458,0.198 10 false : *e 0.229,7.323 0.688,7.521 0.458,0.198 10 false *f 2.063,0.292 2.698,0.521 0.635,0.229 10 false F-MGC 3.75,0.292 4.208,0.49 0.458,0.198 10 false HVB 4.302,0.292 4.854,0.521 0.552,0.229 10 false R-MGC 6.417,0.854 6.875,1.052 0.458,0.198 10 false ENG 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 2.469,1.448 2.927,1.646 0.458,0.198 10 false BRK 5.74,2.021 6.198,2.219 0.458,0.198 10 false SRS 4.396,2.635 4.854,2.833 0.458,0.198 10 false STR 3.76,2.646 4.219,2.844 0.458,0.198 10 false EPS 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 6.479,3.469 6.938,3.667 0.458,0.198 10 false ST 4.99,4.073 5.49,4.302 0.5,0.229 10 false MIR-L 3.063,4.083 3.667,4.354 0.604,0.271 10 false MIR-R 1.542,4.125 2,4.323 0.458,0.198 10 false DLC3 1.948,0.844 2.865,1.042 0.917,0.198 10 false CAN J/C 1 3.896,0.854 4.813,1.052 0.917,0.198 10 false CAN J/C 2 1.927,2.01 2.844,2.208 0.917,0.198 10 false CAN J/C 3 3.844,2.021 4.76,2.219 0.917,0.198 10 false CAN J/C 4 2.948,3.458 3.865,3.656 0.917,0.198 10 false CAN J/C 5 4.813,3.458 5.729,3.656 0.917,0.198 10 false CAN J/C 6
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:
·

The malfunction in the sub bus will not affect the other buses.

·

When a gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus and there is a communication malfunction in one of the ECUs or sensors, the background color of the ECU or sensor will change to red and the ECU or sensor will remain displayed.

·

The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor.




j.

Problem Symptom Pattern I

Details of Malfunction Open in both wires of the main bus line in the sub bus

C352938C01
0.448,2.208 0.906,2.406 0.458,0.198 10 false CGW 2.063,0.281 2.667,0.542 0.604,0.26 10 false F-MGC 3.75,0.292 4.208,0.49 0.458,0.198 10 false HVB 4.302,0.292 4.938,0.531 0.635,0.24 10 false R-MGC 6.417,0.844 6.875,1.042 0.458,0.198 10 false ENG 1.854,1.448 2.313,1.646 0.458,0.198 10 false HV 2.458,1.448 2.917,1.646 0.458,0.198 10 false BRK 1.854,2.688 2.313,2.885 0.458,0.198 10 false MB 3.74,2.615 4.198,2.813 0.458,0.198 10 false EPS 4.396,2.615 4.854,2.813 0.458,0.198 10 false STR 5.74,2.021 6.198,2.219 0.458,0.198 10 false SRS 6.479,3.469 6.938,3.667 0.458,0.198 10 false ST 3.063,4.073 3.583,4.344 0.521,0.271 10 false MIR-R 5,4.073 5.5,4.271 0.5,0.198 10 false MIR-L 1.542,4.125 2,4.323 0.458,0.198 10 false DLC3 1.958,0.844 2.813,1.042 0.854,0.198 10 false CAN J/C 1 1,0.656 1.458,0.854 0.458,0.198 10 false *a 5.615,0.167 6.073,0.365 0.458,0.198 10 false : *e 1,1.823 1.458,2.021 0.458,0.198 10 false *b 1.708,3.073 2.167,3.271 0.458,0.198 10 false *c 1,3.927 1.458,4.125 0.458,0.198 10 false *d 0.219,7.271 0.677,7.469 0.458,0.198 10 false *f 3.875,0.844 4.729,1.042 0.854,0.198 10 false CAN J/C 2 1.958,2.021 2.813,2.219 0.854,0.198 10 false CAN J/C 3 3.885,2.01 4.74,2.208 0.854,0.198 10 false CAN J/C 4 2.896,3.448 3.75,3.646 0.854,0.198 10 false CAN J/C 5 4.802,3.448 5.656,3.646 0.854,0.198 10 false CAN J/C 6
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


HINT:

Due to the malfunction, ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires will be displayed as not communicating and their background color will be red.




How to Use "Communication Bus check (Detail)" Screen in Inspection


a.

If the CAN communication system is currently normal but has communication stop history, determine the malfunctioning part using Communication Bus Check (Detail) as follows:

NOTICE:
·

The following CAN bus wiring diagram or communication bus check screen is provided only as an example. This wiring diagram or screen differs from the actual one for this vehicle.

·

The Lost Communication Time column displays the longest period of time in seconds that the central gateway ECU (network gateway ECU) detected a communication stop in the respective ECU or sensor.

·

The Lost Communication Trip column displays the trip in which the central gateway ECU (network gateway ECU) detected the longest communication stop in the respective ECU or sensor.

·

When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).

·

In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose CAN communication system, refer to the System Diagram.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>SYSTEM DIAGRAM



HINT:
·

If the CAN communication system is currently malfunctioning, it is recommended to use Communication Bus Check rather than Communication Bus Check (Detail) for determining the suspected area.

·

The communication error history of ECUs or sensors which have communication error history can be displayed on the "Communication Bus Check (Detail)" screen.

·

Lost Communication Time and Lost Communication Trip are only displayed for the central bus.

·

Lost Communication Time and Lost Communication Trip are not displayed for sub buses.




b.

If there is an ECU or sensor displayed with a red background on the "Communication Bus Check (Detail)" screen to indicate that it was not communicating, it is suspected that the ECU or sensor was not communicating.

Details of Malfunction Past malfunction in the wire harness or power supplied to F-MGC in Bus 2

C352939C01
0.448,2.198 0.906,2.396 0.458,0.198 10 false CGW 2.063,0.281 2.625,0.51 0.563,0.229 10 false F-MGC 3.76,0.281 4.219,0.479 0.458,0.198 10 false HVB 4.302,0.281 4.896,0.531 0.594,0.25 10 false R-MGC 6.417,0.844 6.875,1.042 0.458,0.198 10 false ENG 5.74,2.021 6.198,2.219 0.458,0.198 10 false SRS 2.469,1.438 2.927,1.635 0.458,0.198 10 false BRK 1.865,1.448 2.323,1.646 0.458,0.198 10 false HV 1.865,2.688 2.323,2.885 0.458,0.198 10 false MB 1.521,4.135 1.979,4.333 0.458,0.198 10 false DLC3 3.073,4.083 3.604,4.344 0.531,0.26 10 false MIR-R 4.99,4.083 5.479,4.313 0.49,0.229 10 false MIR-L 6.479,3.469 6.938,3.667 0.458,0.198 10 false ST 4.385,2.625 4.844,2.823 0.458,0.198 10 false STR 3.74,2.635 4.198,2.833 0.458,0.198 10 false EPS 1.99,0.844 2.729,1.021 0.74,0.177 10 false CAN J/C 1 1,0.667 1.458,0.865 0.458,0.198 10 false *a 0.99,1.792 1.448,1.99 0.458,0.198 10 false *b 1.698,3.052 2.156,3.25 0.458,0.198 10 false *c 1.021,3.938 1.479,4.135 0.458,0.198 10 false *d 0.656,4.865 1.115,5.063 0.458,0.198 10 false : *e 2.25,5.438 2.708,5.635 0.458,0.198 10 false *f 3.865,0.844 4.604,1.021 0.74,0.177 10 false CAN J/C 2 1.948,2.01 2.688,2.188 0.74,0.177 10 false CAN J/C 3 3.896,2.021 4.635,2.198 0.74,0.177 10 false CAN J/C 4 2.927,3.448 3.667,3.625 0.74,0.177 10 false CAN J/C 5 4.823,3.448 5.563,3.625 0.74,0.177 10 false CAN J/C 6
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction *f Background color is red


Description of "Communication Bus Check (Detail)" Screen
Bus Type Background Color Connection Status
Bus White Either of the following:
·

Communication has been normal.

·

Lost Communication Time is below 6 seconds.


Red Lost Communication Time is 6 seconds or more.
Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*1

·

No ECUs or sensors are connected to the bus.*2


Sub bus White Lost Communication Time is displayed as "-".
Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*3

·

No ECUs or sensors are connected to the sub bus.*4



HINT:
·

Check the values of Lost Communication Trip and Current Trip for the ECUs or sensors that have a red background color.

·

If the values of Lost Communication Trip and Current Trip are the same for an ECU or sensor, the ECU or sensor is currently not communicating. In this case, it is recommended to use Communication Bus Check rather than Communication Bus Check (Detail) for determining the suspected area.

·

In the "Communication Bus Check (Detail)" screen shown in the illustration, F-MGC had a communication malfunction in the 10th trip. Thus, it is suspected that F-MGC was not communicating.

·

*1: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*2: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*3: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*4: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.





DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.

·

If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If there is a malfunction currently, DTCs can be checked by performing steps in the DTC check procedure.



a.

ECM / GTS Display "Engine"

HINT:

DTC communication uses the CAN communication system.


Powertrain > Engine > Trouble Codes
50001 372
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to SFI System

A25A-FKS (w/ Canister Pump Module): Click here(Click here)

A25A-FKS (w/o Canister Pump Module): Click here(Click here)

M20A-FKS: Click here(Click here)

U010187* Lost Communication with TCM Missing Message Communication stop occurs between the ECM and transmission control ECU continuously for approximately 2 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. The MIL (Check engine warning light) illuminates. - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the ECM and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U028487 Lost Communication with Active Grille Air Shutter Module "A" Missing Message Communication stop occurs between the ECM and swing grille actuator assembly continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U110387 Lost Communication with Stop and Start Control Module Missing Message Communication stop occurs between the ECM and the engine stop and start ECU continuously for 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. - - DTC is stored until it is cleared using the GTS.


b.

ECM / GTS Display "Transmission" (for Automatic Transmission)

HINT:

DTC communication uses the CAN communication system.


Powertrain > Transmission > Trouble Codes
50001 373
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Automatic Transaxle System.

for 2WD: Click here(Click here)

for 4WD/AWD: Click here(Click here)

U010087* Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the ECM and transmission control ECU continuously for 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. The MIL (Check engine warning light) illuminates. - DTC is stored until it is cleared using the GTS.
U110387 Lost Communication with Stop and Start Control Module Missing Message Communication stop occurs between the ECM and the engine stop and start ECU continuously for 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the ECM is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. - - DTC is stored until it is cleared using the GTS.


c.

Transmission Control ECU / GTS Display "Transmission" (for CVT)

HINT:

DTC communication uses the CAN communication system.


Powertrain > Transmission > Trouble Codes
50001 373
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Continuously Variable Transaxle System

for 2WD: Click here(Click here)

for 4WD/AWD: Click here(Click here)

U010087* Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the transmission control ECU and ECM continuously for 2 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the transmission control ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-Axis Acceleration Sensor Module Missing Message Communication stop occurs between the transmission control ECU and airbag sensor assembly continuously for 2 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the transmission control ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the transmission control ECU and brake actuator assembly (skid control ECU) continuously for 3 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the transmission control ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. - - DTC is stored until it is cleared using the GTS.
U110387 Lost Communication with Stop and Start Control Module Missing Message Communication stop occurs between the transmission control ECU and the engine stop and start ECU continuously for 2 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the transmission control ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.


d.

Engine Stop and Start ECU / GTS Display "Stop and Start" (w/ Stop and Start System)

HINT:

DTC communication uses the CAN communication system.


Powertrain > Stop and Start > Trouble Codes
50001 392
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the engine stop and start ECU and ECM continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U010187 Lost Communication with TCM Missing Message Communication stop occurs between the engine stop and start ECU and ECM continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the engine stop and start ECU and steering sensor continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the engine stop and start ECU and brake actuator assembly (skid control ECU) continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the engine stop and start ECU and the rack and pinion power steering gear assembly continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the engine stop and start ECU and main body ECU (multiplex network body ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U015187 Lost Communication with Restraints Control Module Missing Message Communication stop occurs between the engine stop and start ECU and airbag sensor assembly continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U016487 Lost Communication with HVAC Control Module Missing Message Communication stop occurs between the engine stop and start ECU and air conditioning amplifier assembly continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U023A87 Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the engine stop and start ECU and forward recognition camera continuously for 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.
U111087 Lost Communication with Clearance Sonar Module Missing Message Communication stop occurs between the engine stop and start ECU and clearance warning ECU assembly continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the engine stop and start ECU is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. The ECO RUN blinks. - DTC is stored until it is cleared using the GTS.


e.

Brake Actuator Assembly (Skid Control ECU) / GTS Display "Brake/EPB*"

HINT:

DTC communication uses the CAN communication system.


Chassis > Brake/EPB > Trouble Codes
50001 435
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

EPB*: Electric Parking Brake

U007488 Control Module Communication Bus "B" Off Bus Off The brake actuator assembly (skid control ECU) cannot send and receive data (The bus is off) for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the brake actuator assembly (skid control ECU) is 9.6 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds.
·

The ABS warning light illuminates.

·

The slip indicator light illuminates.

·

The brake hold operated indicator light blinks.

·

The brake warning light (red) illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the brake actuator assembly (skid control ECU) and ECM continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the brake actuator assembly (skid control ECU) is 9.6 V or higher.

·

The vehicle speed is 6 km/h (4 mph) or more.


Drive the vehicle for 5 seconds or more at a speed of 6 km/h (4 mph) or more.
·

The slip indicator light illuminates.

·

The brake hold operated indicator light blinks.

·

The electric parking brake auto off indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U010187 Lost Communication with TCM Missing Message Communication stop occurs between the brake actuator assembly (skid control ECU) and transmission control ECU continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the brake actuator assembly (skid control ECU) is 9.6 V or higher.

·

The vehicle speed is 6 km/h (4 mph) or more.


Drive the vehicle for 5 seconds or more at a speed of 6 km/h (4 mph) or more.
·

The slip indicator light illuminates.

·

The brake hold operated indicator light blinks.

·

The electric parking brake auto off indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the brake actuator assembly (skid control ECU) and airbag sensor assembly continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the brake actuator assembly (skid control ECU) is 9.6 V or higher.

·

The vehicle speed is 6 km/h (4 mph) or more.


Drive the vehicle for 4 seconds or more at a speed of 6 km/h (4 mph) or more.
·

The slip indicator light illuminates.

·

The brake hold operated indicator light blinks.

·

The electric parking brake auto off indicator light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the brake actuator assembly (skid control ECU) and steering sensor continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the brake actuator assembly (skid control ECU) is 9.6 V or higher.

·

The vehicle speed is 6 km/h (4 mph) or more.


Drive the vehicle for 4 seconds or more at a speed of 6 km/h (4 mph) or more.
·

The slip indicator light illuminates.

·

The brake hold operated indicator light blinks.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the brake actuator assembly (skid control ECU) and main body ECU (multiplex network body ECU) continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the brake actuator assembly (skid control ECU) is 9.6 V or higher.

·

The vehicle speed is 6 km/h (4 mph) or more.


Drive the vehicle for 5 seconds or more at a speed of 6 km/h (4 mph) or more.
·

The electric parking brake auto off indicator light illuminates.

·

The brake hold operated indicator light blinks.


- DTC is stored until it is cleared using the GTS.
U015187 Lost Communication with Restraints Control Module Missing Message Communication stop occurs between the brake actuator assembly (skid control ECU) and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the brake actuator assembly (skid control ECU) is 9.6 V or higher.

·

The vehicle speed is 6 km/h (4 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 6 km/h (4 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110387 Lost Communication with Stop and Start Control Module Missing Message Communication stop occurs between the brake actuator assembly (skid control ECU) and the engine stop and start ECU continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the brake actuator assembly (skid control ECU) is 9.6 V or higher.

·

The vehicle speed is 6 km/h (4 mph) or more.


Drive the vehicle for 5 seconds or more at a speed of 6 km/h (4 mph) or more.
·

The electric parking brake auto off indicator light illuminates.

·

The brake hold operated indicator light blinks.


- DTC is stored until it is cleared using the GTS.


f.

Rack and Pinion Power Steering Gear Assembly / GTS Display "EMPS"

HINT:

DTC communication uses the CAN communication system.


Chassis > EMPS > Trouble Codes
50001 405
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the rack and pinion power steering gear assembly and ECM continuously for 5 minutes or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.

·

The vehicle speed is 20 km/h (12 mph) or more.


Drive the vehicle for approximately 5 minutes or more at a speed of 20 km/h (12 mph) or more. - - DTC remains stored only while malfunction is occurring.
Communication stop occurs between the rack and pinion power steering gear assembly and ECM continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. - - DTC remains stored only while malfunction is occurring.
U0126 Lost Communication With Steering Angle Sensor Module Communication stop occurs between the rack and pinion power steering gear assembly and steering sensor continuously for 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - - DTC remains stored only while malfunction is occurring.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the rack and pinion power steering gear assembly and brake actuator assembly (skid control ECU) continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. The EPS warning light illuminates. - DTC remains stored only while malfunction is occurring.
U023A Lost Communication with Front Camera Module Communication stop occurs between the rack and pinion power steering gear assembly and forward recognition camera continuously for approximately 2 seconds or more. 3 seconds or more elapse after the ignition switch is turned to ON. Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC remains stored only while malfunction is occurring.
U1103 Lost Communication with Stop and Start Control Module Communication stop occurs between the rack and pinion power steering gear assembly and the engine stop and start ECU continuously for 5 minutes or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.

·

The vehicle speed is 20 km/h (12 mph) or more.


Drive the vehicle for approximately 5 minutes or more at a speed of 20 km/h (12 mph) or more. - - DTC remains stored only while malfunction is occurring.


g.

ECM / GTS Display "Cruise Control" (w/ Cruise Control System)

HINT:

DTC communication uses the CAN communication system.


Powertrain > Cruise Control > Trouble Codes
50001 374
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012287 Lost Communication with Vehicle Dynamics Control Module Missing Message Communication stop occurs between the ECM and brake actuator assembly (skid control ECU) continuously for approximately 3 seconds or more.
·

Elapse after the ignition switch is turned to ON.

·

The dynamic radar cruise control system is in operation.


Turn the dynamic radar cruise control system on and wait for 3 seconds or more - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


h.

ECM / GTS Display "Radar Cruise1" (w/ Pre-collision System)

HINT:

DTC communication uses the CAN communication system.


Powertrain > Cruise Control > Trouble Codes
50001 374
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*1: w/ Full-speed Range Following Function

*2: w/o Full-speed Range Following Function

U010087 Lost Communication With ECM/PCM "A" Missing Message Communication stop occurs between the ECM and brake actuator assembly (skid control ECU) continuously for approximately 1 second or more. All conditions are met:
·

Elapse after the ignition switch is turned to ON.

·

The dynamic radar cruise control system is in operation.


Turn the dynamic radar cruise control system on. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U010487 Lost Communication with Cruise Control Module Missing Message Communication stop occurs between the ECM and millimeter wave radar sensor assembly continuously for approximately 1 second or more. All conditions are met:
·

Elapse after the ignition switch is turned to ON.

·

The dynamic radar cruise control system is in operation.

·

The vehicle speed is 5 km/h (3 mph) or more.*1

·

The vehicle speed is 25 km/h (16 mph) or more.*2


·

Turn the dynamic radar cruise control system on and drive the vehicle speed of 5 km/h (3 mph) or more.*1

·

Turn the dynamic radar cruise control system on and drive the vehicle speed of 25 km/h (16 mph) or more.*2


- Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012287 Lost Communication with Vehicle Dynamics Control Module Missing Message Communication stop occurs between the ECM and brake actuator assembly (skid control ECU) continuously for approximately 3 seconds or more. All conditions are met:
·

Elapse after the ignition switch is turned to ON.

·

The dynamic radar cruise control system is in operation.


Turn the dynamic radar cruise control system on. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


i.

Forward Recognition Camera / GTS Display "Radar Cruise2" (w/ Pre-collision System)

HINT:

DTC communication uses the CAN communication system.


Powertrain > Radar Cruise2 > Trouble Codes
50001 426
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*1: w/ Full-speed Range Following Function

*2: w/o Full-speed Range Following Function

*3: Refer to Dynamic Radar Cruise Control System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.*1

·

The vehicle speed is 25 km/h (16 mph) or more.*2


·

Drive the vehicle for approximately 4 seconds or more at a speed of 5 km/h (3 mph) or more.*1

·

Drive the vehicle for approximately 4 seconds or more at a speed of 25 km/h (16 mph) or more.*2


- Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.*1

·

The vehicle speed is 25 km/h (16 mph) or more.*2


·

Drive the vehicle for approximately 4 seconds or more at a speed of 5 km/h (3 mph) or more.*1

·

Drive the vehicle for approximately 4 seconds or more at a speed of 25 km/h (16 mph) or more.*2


- Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.*1

·

The vehicle speed is 25 km/h (16 mph) or more.*2


·

Drive the vehicle for approximately 4 seconds or more at a speed of 5 km/h (3 mph) or more.*1

·

Drive the vehicle for approximately 4 seconds or more at a speed of 25 km/h (16 mph) or more.*2


- Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.*1

·

The vehicle speed is 25 km/h (16 mph) or more.*2


·

Drive the vehicle for approximately 5 seconds or more at a speed of 5 km/h (3 mph) or more.*1

·

Drive the vehicle for approximately 5 seconds or more at a speed of 25 km/h (16 mph) or more.*2


- Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.*1

·

The vehicle speed is 25 km/h (16 mph) or more.*2


·

Drive the vehicle for 8 seconds or more at a speed of 5 km/h (3 mph) or more.*1

·

Drive the vehicle for 8 seconds or more at a speed of 25 km/h (16 mph) or more.*2


- Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587*3 Lost Communication with Control Front Distance Range Sensor Missing Message The forward recognition camera does not receive data from the millimeter wave radar sensor assembly for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or more.


With the dynamic radar cruise operating, drive the vehicle for approximately 5 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030051*3 Internal Control Module Software Incompatibility Not Programmed The control system information sent from the ECM remains undefined by the forward recognition camera for 3 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or more.


With the dynamic radar cruise operating, drive the vehicle for approximately 6 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030057*3 Internal Control Module Software Incompatibility Invalid / Incompatible Software Component The vehicle information sent from the ECM does not match that stored in the forward recognition camera for 1 second or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or more.


With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U031851*3 Software Incompatibility with Brake System Control Module Not Programmed The vehicle information sent from brake actuator assembly (skid control ECU) remains undefined by the forward recognition camera for 3 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or more.


With the dynamic radar cruise operating, drive the vehicle for approximately 6 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U031857*3 Software Incompatibility with Brake System Control Module Invalid / Incompatible Software Component The vehicle information sent from the brake actuator assembly (skid control ECU) does not match that stored in the forward recognition camera for 2 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or more.


With the dynamic radar cruise operating, drive the vehicle for approximately 5 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U032251*3 Software Incompatibility with Body Control Module Not Programmed The vehicle information sent from main body ECU (multiplex network body ECU) remains undefined by the forward recognition camera for 6 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or more.


With the dynamic radar cruise operating, drive the vehicle for approximately 9 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U032257*3 Software Incompatibility with Body Control Module Invalid / Incompatible Software Component The vehicle information sent from the main body ECU (multiplex network body ECU) does not match that stored in the forward recognition camera for 4 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or more.


With the dynamic radar cruise operating, drive the vehicle for approximately 7 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U040181*3 The information sent from the ECM does not match that stored in the forward recognition camera. The information sent from the ECM does not match that stored in the forward recognition camera. All conditions are met:
·

The ignition switch is ON for approximately 3 seconds or more.

·

The dynamic radar cruise control system is in operation.

·

The power source voltage of the forward recognition camera is 10 V or more.


With the dynamic radar cruise operating, drive the vehicle for approximately 3 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110687 Lost Communication with Electric Parking Brake Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.*1

·

The vehicle speed is 25 km/h (16 mph) or more.*2


·

Drive the vehicle for approximately 5 seconds or more at a speed of 5 km/h (3 mph) or more.*1

·

Drive the vehicle for approximately 5 seconds or more at a speed of 25 km/h (16 mph) or more.*2


- Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


j.

Forward Recognition Camera / GTS Display "Pre-Collision System" (w/ Pre-collision System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Pre-Collision System > Trouble Codes
50001 432
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Pre-collision System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle speed of 5 km/h (3 mph) or more. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle speed of 5 km/h (3 mph) or more. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU). All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110487 Lost Communication with Driving Support ECU Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. The PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


k.

Forward Recognition Camera / GTS Display "Lane Control" (w/ Pre-collision System)

HINT:

DTC communication uses the CAN communication system.


Chassis > Lane Control > Trouble Codes
50001 418
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Lane Control System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The LTA main switch is on.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U010187 Lost Communication with TCM Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The LTA main switch is on.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The LTA main switch is on.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LTA main switch is on.


Turn the ignition switch to ON and wait at least 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LTA main switch is on.


Turn the ignition switch to ON and wait at least 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the forward recognition camera and the rack and pinion power steering gear assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LTA main switch is on.


Turn the ignition switch to ON and wait at least 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 50 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LTA main switch is on.


Turn the ignition switch to ON and wait at least 53 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 7 V or higher.

·

The LTA main switch is on.


Turn the ignition switch to ON and wait at least 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030051* Internal Control Module Software Incompatibility Not Programmed The vehicle information sent from the ECM remains undefined by the forward recognition camera. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is turned to ON.

·

The LTA main switch is on.

·

The power source voltage of the forward recognition camera is 7 V or more.


Turn the LTA main switch on and wait for at least approximately 3 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030057* Internal Control Module Software Incompatibility Invalid/Incompatible Software Component The vehicle information sent from the ECM does not match that stored in the forward recognition camera for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is turned to ON.

·

The LTA main switch is on.

·

The power source voltage of the forward recognition camera is 7 V or more.


Turn the LTA main switch on and wait for at least approximately 8 seconds. The lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


l.

Forward Recognition Camera / GTS Display "Road Sign Assist" (w/ Road Sign Assist System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Road Sign Assist > Trouble Codes
50001 431
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 50 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 53 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


m.

Forward Recognition Camera / GTS Display "Front Recognition Camera (Front Lighting Control)" (w/ Pre-collision System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Automatic High Beam System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 7 seconds or more at a speed of 1 km/h (1 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 7 seconds or more at a speed of 1 km/h (1 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


n.

Forward Recognition Camera / GTS Display "Front Recognition Camera" (w/ Pre-collision System)

HINT:

DTC communication uses the CAN communication system.


Chassis > Front Recognition Camera > Trouble Codes
50001 430
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the forward recognition camera and ECM continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - - DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.


o.

Millimeter Wave Radar Sensor Assembly / GTS Display "Front Radar Sensor" (w/ Pre-collision System)

HINT:

This ECU uses the CAN communication system for DTC communication.


Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Front Radar Sensor System

Click here(Click here)

U010487* Lost Communication with Driving Support ECU Missing Message The millimeter wave radar sensor assembly does not receive data from the forward recognition camera for approximately 1 second or more. All conditions are met:
·

The ignition switch is ON for approximately 1 second or more.

·

The power source voltage of the millimeter wave radar sensor assembly is 8 V or more.


Turn the ignition switch to ON and wait for at least approximately 2 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030557* Software Incompatibility with Cruise Control Module Invalid / Incompatible Software Component The control system information sent from the forward recognition camera does not match that stored in the millimeter wave radar sensor assembly for 7 seconds or more. All conditions are met:
·

The ignition switch is ON for approximately 1 second or more.

·

The power source voltage of the millimeter wave radar sensor assembly is 8 V or more.


Turn the ignition switch to ON and wait for at least approximately 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


p.

Airbag Sensor Assembly / GTS Display "SRS Airbag" (w/ Occupant Classification System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > SRS Airbag > Trouble Codes
50001 188
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0154 Lost Communication with Restraints Occupant Classification System Module Either of the following conditions is met:
·

Communication stop occurs between the airbag sensor assembly and occupant detection ECU continuously for 5 seconds or more.

·

Checksum error is detected in data received from the occupant detection ECU continuously for 5 seconds or more.


3 seconds or more elapse after the ignition switch is turned to ON. Turn the ignition switch to ON and wait at least 8 seconds. The SRS warning light illuminates. - DTC is stored until it is cleared using the GTS.


q.

Occupant Detection ECU / GTS Display "Occupant Detection" (w/ Occupant Classification System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Occupant Detection > Trouble Codes
50001 394
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0125 Lost Communication With Multi-axis Acceleration Sensor Module Communication stop occurs between the occupant detection ECU and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the occupant detection ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. The SRS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication With Brake System Control Module Communication stop occurs between the occupant detection ECU and brake actuator assembly (skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the occupant detection ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. The SRS warning light illuminates. - DTC is stored until it is cleared using the GTS.


r.

Combination Meter Assembly / GTS Display "Combination Meter"

HINT:
·

DTC communication uses the CAN communication system.



Body Electrical > Combination Meter > Trouble Codes
50001 409
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication with ECM/PCM "A" Missing Message Communication stop occurs between the combination meter assembly and ECM continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds.
·

The MIL (Check engine warning light) illuminates.

·

The tachometer does not operate.


- DTC is stored until it is cleared using the GTS.
U011487 Lost Communication with Four-Wheel Drive Clutch Control Module Missing Message Communication stop occurs between the combination meter assembly and 4WD ECU assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U012787 Lost Communication with Tire Pressure Monitor Module Missing Message Communication stop occurs between the combination meter assembly and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. The tire pressure warning light blinks, and then illuminates. - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the combination meter assembly and brake actuator assembly (skid control ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds.
·

The ABS warning light illuminates.

·

The VSC OFF indicator light illuminates.

·

The brake warning light (red) illuminates.


- DTC is stored until it is cleared using the GTS.
Communication stop occurs between the combination meter assembly and brake actuator assembly (skid control ECU) continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds.
·

The ABS warning light illuminates.

·

The VSC OFF indicator light illuminates.

·

The brake warning light (red) illuminates.


- DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the combination meter assembly and the rack and pinion power steering gear assembly continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. The EPS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the combination meter assembly and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U015187 Lost Communication with Restraints Control Module Missing Message Communication stop occurs between the combination meter assembly and airbag sensor assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. The SRS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U016387 Lost Communication with Navigation Control Module Missing Message Communication stop occurs between the combination meter assembly and the radio and display receiver assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U016487 Lost Communication with HVAC Control Module Missing Message Communication stop occurs between the combination meter assembly and air conditioning amplifier assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U016887 Lost Communication with Vehicle Security Control Module Missing Message Communication stop occurs between the combination meter assembly and certification ECU (smart key ECU assembly) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U018287 Lost Communication with Lighting Control Module Front Missing Message Communication stop occurs between the combination meter assembly and headlight ECU sub-assembly LH continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U023087 Lost Communication with Rear Gate Module Missing Message Communication stop occurs between the combination meter assembly and multiplex network door ECU continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U023387 Lost Communication with Side Obstacle Detection Control Module Right Missing Message Communication stop occurs between the combination meter assembly and blind spot monitor sensor LH continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U023A87 Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the combination meter assembly and forward recognition camera continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. The PCS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U110387 Lost Communication with Stop and Start Control Module Missing Message Communication stop occurs between the combination meter assembly and the engine stop and start ECU continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U110687 Lost Communication with Electric Parking Brake Module Missing Message Communication stop occurs between the combination meter assembly and brake actuator assembly (skid control ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. The brake warning light (red) illuminates. - DTC is stored until it is cleared using the GTS.
U111087 Lost Communication with Clearance Sonar Module Missing Message Communication stop occurs between the combination meter assembly and clearance warning ECU assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U111287 Lost Communication with Combination Switch Module Missing Message Communication stop occurs between the combination meter assembly and steering sensor continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.
U111787 Lost Communication with Accessory Gateway Communication stop occurs between the combination meter assembly and bus buffer ECU continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U113387 Lost Communication with PMN Module Missing Message Communication stop occurs between the combination meter assembly and certification ECU (smart key ECU assembly) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - - DTC is stored until it is cleared using the GTS.


s.

Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Main Body > Trouble Codes
50001 123
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication With ECM/PCM "A" Communication stop occurs between the main body ECU (multiplex network body ECU) and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0101 Lost Communication with TCM Communication stop occurs between the main body ECU (multiplex network body ECU) and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0120 Lost Communication With Starter / Generator Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the main body ECU (multiplex network body ECU) and steering sensor continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and brake actuator assembly (skid control ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and airbag sensor assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0163 Lost Communication with Navigation Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and the radio and display receiver assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0164 Lost Communication with HVAC Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and air conditioning amplifier assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0182 Lost Communication with AFS Communication stop occurs between the main body ECU (multiplex network body ECU) and headlight ECU sub-assembly LH continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0208 Lost Communication with "Seat Control Module A" Communication stop occurs between the main body ECU (multiplex network body ECU) and position control ECU assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0230 Lost Communication with Rear Gate Module Communication stop occurs between the main body ECU (multiplex network body ECU) and multiplex network door ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U023A Lost Communication With Image Processing Module "A" Communication stop occurs between the main body ECU (multiplex network body ECU) and forward recognition camera continuously for 5 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0327 Software Incompatibility with Vehicle Security Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1103 Lost Communication with Stop and Start Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and the engine stop and start ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1106 Lost Communication with Electric Parking Brake Module Communication stop occurs between the main body ECU (multiplex network body ECU) and brake actuator assembly (skid control ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1117 Lost Communication with Accessory Gateway Communication stop occurs between the main body ECU (multiplex network body ECU) and bus buffer ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


t.

Radio and Display Receiver Assembly / GTS Display "Navigation System" (for Radio and Display Type)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Navigation System > Trouble Codes
50001 212
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0073 Sending Malfunction (Navigation to APGS) The radio and display receiver assembly is unable to send or receive data 10 times consecutively. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - - DTC is stored until it is cleared using the GTS.
U0100 Engine ECU Communication Communication stop occurs between the radio and display receiver assembly and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Communication stop occurs between the radio and display receiver assembly and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Meter ECU Communication Communication stop occurs between the radio and display receiver assembly and combination meter assembly continuously for 30 seconds or more. All conditions are met:
·

30 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 60 seconds. - - DTC is stored until it is cleared using the GTS.
U0164 Air Conditioner ECU Communication Communication stop occurs between the radio and display receiver assembly and air conditioning amplifier assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0198 Lost Communication with Telematic Control Module Communication stop occurs between the radio and display receiver assembly and telephone transceiver assembly. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait. - - DTC is stored until it is cleared using the GTS.
U023B Lost Communication with Image Processing Module "B" Communication stop occurs between the radio and display receiver assembly and parking assist ECU continuously for approximately 12 seconds or more. All conditions are met:
·

11 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 23 seconds. - - DTC is stored until it is cleared using the GTS.
U0265 Lost Communication with Image Processing Sensor A Communication stop occurs between the radio and display receiver assembly and television camera assembly continuously for approximately 12 seconds or more. All conditions are met:
·

11 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 23 seconds. - - DTC is stored until it is cleared using the GTS.
U1110 Clearance Sonar ECU Communication Communication stop occurs between the radio and display receiver assembly and clearance warning ECU assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


u.

Telephone Transceiver Assembly / GTS Display "Telematics" ( w/ Telematics System for ERA-GLONASS)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Telematics > Trouble Codes
50001 233
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication With ECM/PCM "A" Communication stop occurs between the telephone transceiver assembly and ECM continuously for 15 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the telephone transceiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 25 seconds. - - DTC is stored until it is cleared using the GTS.


v.

Telephone Transceiver Assembly / GTS Display "Telematics" (w/ Telematics System for eCall)

HINT:

DTC communication uses the CAN communication system.


DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U014087 Lost Communicat ion with Body Control Module Communication stop occurs between the telephone transceiver assembly and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the telephone transceiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - The DTC is stored only while the malfunction is present.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the telephone transceiver assembly and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON..

·

The power source voltage of the telephone transceiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - The DTC is stored only while the malfunction is present.
U016387 Lost Communication with Navigation Control Module Communication stop occurs between the telephone transceiver assembly and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the telephone transceiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 second. - - The DTC is stored only while the malfunction is present.


w.

Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Air Conditioner > Trouble Codes
50001 121
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication With ECM/PCM "A" Communication stop occurs between the air conditioning amplifier assembly and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.

·

The vehicle speed is 30 km/h (19 mph) or more.


Drive the vehicle for 20 seconds or more at a speed of 30 km/h (19 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0131 Lost Communication With Power Steering Control Module Communication stop occurs between the air conditioning amplifier assembly and the rack and pinion power steering gear assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.

·

The vehicle speed is 30 km/h (19 mph) or more.


Drive the vehicle for 20 seconds or more at a speed of 30 km/h (19 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the air conditioning amplifier assembly and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.

·

The vehicle speed is 30 km/h (19 mph) or more.


Drive the vehicle for 20 seconds or more at a speed of 30 km/h (19 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module Communication stop occurs between the air conditioning amplifier assembly and airbag sensor assembly. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.

·

The vehicle speed is 30 km/h (19 mph) or more.


Drive the vehicle speed of 30 km/h (19 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the air conditioning amplifier assembly and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.

·

The vehicle speed is 30 km/h (19 mph) or more.


Drive the vehicle for 20 seconds or more at a speed of 30 km/h (19 mph) or more. - - DTC is stored until it is cleared using the GTS.


x.

Clearance Warning ECU Assembly / GTS Display "Clearance Warning" (w/ TOYOTA Parking Assist-sensor System with Parking Support Brake System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Clearance Warning > Trouble Codes
50001 438
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Parking Support Brake System

Click here(Click here)

U010087 Lost Communication with ECM/PCM "A" Communication stop occurs between the clearance warning ECU assembly and ECM continuously for approximately 6 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 9 seconds. The PKSB OFF indicator light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012587 Lost Communication With Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the clearance warning ECU assembly and airbag sensor assembly continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. The PKSB OFF indicator light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication With Steering Angle Sensor Module Communication stop occurs between the clearance warning ECU assembly and steering sensor continuously for approximately 6 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 9 seconds. The PKSB OFF indicator light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Communication stop occurs between the clearance warning ECU assembly and brake actuator assembly (skid control ECU) continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. The PKSB OFF indicator light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Communication stop occurs between the clearance warning ECU assembly and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U015587 Lost Communication With Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the clearance warning ECU assembly and combination meter assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U016487 Lost Communication with HVAC Control Module Communication stop occurs between the clearance warning ECU assembly and air conditioning amplifier assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U110387 Lost Communication with Stop and Start Control Module Communication stop occurs between the clearance warning ECU assembly and the engine stop and start ECU continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. - - DTC is stored until it is cleared using the GTS.
U117787* Lost Communication with Side Obstacle Detection Control Module Left (ch2) Missing Message Communication stop occurs between the clearance warning ECU assembly and blind spot monitor sensor LH continuously for 12 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 15 seconds. - - DTC is stored until it is cleared using the GTS.
U117887* Lost Communication with Side Obstacle Detection Control Module Right (ch2) Missing Message Communication stop occurs between the clearance warning ECU assembly and blind spot monitor sensor RH continuously for 12 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 15 seconds. - - DTC is stored until it is cleared using the GTS.


y.

Clearance Warning ECU Assembly / GTS Display "Clearance Sonar" (w/ TOYOTA Parking Assist-sensor System without Parking Support Brake System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Clearance Sonar > Trouble Codes
50001 170
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM "A" Either of the following conditions is met:
·

Communication stop occurs between the clearance warning ECU assembly and ECM continuously for approximately 6 seconds or more.

·

Communication stop occurs between the clearance warning ECU assembly and ECM continuously for approximately 1 second or more.

·

Communication stop occurs between the clearance warning ECU assembly and ECM continuously for approximately 2 seconds or more.

·

Communication stop occurs between the clearance warning ECU assembly and ECM continuously for approximately 4 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 9 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0101 Lost Communication with TCM Communication stop occurs between the clearance warning ECU assembly and ECM continuously for 5 seconds or more. All conditions are met:
·

5 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the clearance warning ECU assembly and main body ECU (multiplex network body ECU) continuously for 4 seconds or more. All conditions are met:
·

5 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 9 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the clearance warning ECU assembly and combination meter assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the clearance warning ECU assembly is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


z.

Blind Spot Monitor Sensor LH / GTS Display "Blind Spot Monitor Master" (w/ Blind Spot Monitor System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Blind Spot Monitor System

Click here(Click here)

U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the blind spot monitor sensor LH and ECM continuously for approximately 11 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 12 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0125 Lost Communication with Yaw Rate Sensor Module Communication stop occurs between the blind spot monitor sensor LH and airbag sensor assembly continuously for approximately 4 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the blind spot monitor sensor LH and steering sensor continuously for approximately 4 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the blind spot monitor sensor LH and brake actuator assembly (skid control ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the blind spot monitor sensor LH and main body ECU (multiplex network body ECU) continuously for approximately 11 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 12 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0232* Lost Communication with Blind Spot Monitor Slave Module Communication stop occurs between the blind spot monitor sensor LH and blind spot monitor sensor RH continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor LH is 10 V or higher.


Turn the ignition switch to ON and wait at least 12 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


aa.

Blind Spot Monitor Sensor RH / GTS Display "Blind Spot Monitor Slave" (w/ Blind Spot Monitor System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Blind Spot Monitor System

Click here(Click here)

U0100* Lost Communication with ECM/PCM "A" Communication stop occurs between the blind spot monitor sensor RH and ECM continuously for approximately 11 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor RH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 12 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0125* Lost Communication with Yaw Rate Sensor Module Communication stop occurs between the blind spot monitor sensor RH and airbag sensor assembly continuously for approximately 4 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor RH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0126* Lost Communication with Steering Angle Sensor Module Communication stop occurs between the blind spot monitor sensor RH and steering sensor continuously for approximately 4 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor RH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0129* Lost Communication with Brake System Control Module Communication stop occurs between the blind spot monitor sensor RH and brake actuator assembly (skid control ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor RH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0142* Lost Communication with Body Control Module "B" Communication stop occurs between the blind spot monitor sensor RH and main body ECU (multiplex network body ECU) continuously for approximately 11 seconds or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor RH is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 12 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0233* Lost Communication with Blind Spot Monitor Master Module Communication stop occurs between the blind spot monitor sensor RH and blind spot monitor sensor LH continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the blind spot monitor sensor RH is 10 V or higher.


Turn the ignition switch to ON and wait at least 12 seconds. The BSM indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


ab.

Certification ECU (Smart Key ECU Assembly) / GTS Display "Entry&Start" (w/ Entry and Start System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Entry&Start > Trouble Codes
50001 125
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication With ECM/PCM "A" Communication stop occurs between the certification ECU (smart key ECU assembly) and ECM continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0230 Lost Communication with Rear Gate Module Communication stop occurs between the certification ECU (smart key ECU assembly) and multiplex network door ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1103 Lost Communication with Stop and Start Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and the engine stop and start ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1117 Lost Communication with Accessory Gateway Communication stop occurs between the certification ECU (smart key ECU assembly) and bus buffer ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


ac.

Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control" (w/ Entry and Start System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Power Source Control > Trouble Codes
50001 223
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication With ECM/PCM "A" Communication stop occurs between the certification ECU (smart key ECU assembly) and ECM continuously for 3 seconds or more. All conditions are met:
·

A power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module "B" Communication stop occurs between the certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) continuously for 3 seconds or more. All conditions are met:
·

A power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and combination meter assembly continuously for 3 seconds or more. All conditions are met:
·

A power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U1103 Lost Communication with Stop and Start Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and the engine stop and start ECU continuously for 5 seconds or more. All conditions are met:
·

A power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.
U1117 Lost Communication with Accessory Gateway Communication stop occurs between the certification ECU (smart key ECU assembly) and bus buffer ECU continuously for 5 seconds or more. All conditions are met:
·

A power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.


ad.

Headlight ECU Sub-assembly LH / GTS Display "HL AutoLeveling"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Lighting System

Click here(Click here)

U0073 Control Module Communication Bus Off Either of the following conditions is met:
·

Bus off condition is detected.

·

CAN bus is not connected.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - Output during the trip in which the malfunction occurred.
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the headlight ECU sub-assembly LH and ECM continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC remains stored only while malfunction is occurring.
U0101 Lost Communication with TCM Communication stop occurs between the headlight ECU sub-assembly LH and ECM continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the headlight ECU sub-assembly LH and steering sensor continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the headlight ECU sub-assembly LH and brake actuator assembly (skid control ECU) continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the headlight ECU sub-assembly LH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the headlight ECU sub-assembly LH and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0242 Lost Communication With Headlamp Control Module "B" Communication stop occurs between the headlight ECU sub-assembly LH and headlight ECU sub-assembly RH continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U1000* CAN Communication Failure(Message Registry) CAN message register malfunction is detected. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly LH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - Output during the trip in which the malfunction occurred.


ae.

Headlight ECU Sub-assembly RH / GTS Display "HL AutoLeveling (Sub)"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Lighting System

Click here(Click here)

U0073 Control Module Communication Bus Off Either of the following conditions is met:
·

Bus off condition is detected.

·

CAN bus is not connected.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - Output during the trip in which the malfunction occurred.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the headlight ECU sub-assembly RH and steering sensor continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC remains stored only while malfunction is occurring.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the headlight ECU sub-assembly RH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0182 Lost Communication With Lighting Control Module Front Communication stop occurs between the headlight ECU sub-assembly RH and headlight ECU sub-assembly LH continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC remains stored only while malfunction is occurring.
U1000* CAN Communication Failure (Message Registry) CAN message register malfunction is detected. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the headlight ECU sub-assembly RH is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - Output during the trip in which the malfunction occurred.


af.

Multiplex Network Door ECU / GTS Display "Back Door" (w/ Power Back Door System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Back Door > Trouble Codes
50001 159
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0101 Lost Communication with TCM Communication stop occurs between the multiplex network door ECU and ECM continuously for 10 seconds or more. The power source voltage of the multiplex network door ECU is 10.8 V or higher. Wait at least 10 seconds with the power source voltage of the multiplex network door ECU at 10.8 V or higher. - - DTC remains stored only while malfunction is occurring.
U0122 Lost Communication with Vehicle Dynamics Control Module Communication stop occurs between the multiplex network door ECU and brake actuator assembly (skid control ECU) continuously for 10 seconds or more. The power source voltage of the multiplex network door ECU is 10.8 V or higher. Wait at least 10 seconds with the power source voltage of the multiplex network door ECU at 10.8 V or higher. - - DTC remains stored only while malfunction is occurring.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the multiplex network door ECU and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. The power source voltage of the multiplex network door ECU is 10.8 V or higher. Wait at least 10 seconds with the power source voltage of the multiplex network door ECU at 10.8 V or higher. - - DTC remains stored only while malfunction is occurring.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the multiplex network door ECU and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

The ignition switch is ACC.

·

The power source voltage of the multiplex network door ECU is 10.8 V or higher.


Turn the ignition switch to ACC and wait at least 10 seconds with the power source voltage of the multiplex network door ECU at 10.8 V or higher. - - DTC remains stored only while malfunction is occurring.
U1117 Lost Communication with Accessory Gateway Communication stop occurs between the multiplex network door ECU and bus buffer ECU continuously for 10 seconds or more. The power source voltage of the multiplex network door ECU is 10.8 V or higher. Wait at least 10 seconds with the power source voltage of the multiplex network door ECU at 10.8 V or higher. - - DTC remains stored only while malfunction is occurring.


ag.

Television Camera Assembly / GTS Display "Rear Camera" (w/ Parking Assist Monitor System)

HINT:

DTC communication uses the CAN communication system.


Chassis > Rear Camera > Trouble Codes
50001 85
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Parking Assist Monitor System

Click here(Click here)

U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the television camera assembly and ECM continuously for 11 seconds or more. 3 seconds or more elapse after the ignition switch is turned to ON. Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the television camera assembly and steering sensor continuously for 11 seconds or more. 3 seconds or more elapse after the ignition switch is turned to ON. Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Communication stop occurs between the television camera assembly and main body ECU (multiplex network body ECU) continuously for 11 seconds or more. 3 seconds or more elapse after the ignition switch is turned to ACC. Turn the ignition switch to ACC and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0163 Lost Communication with Navigation Control Module Communication stop occurs between the television camera assembly and radio and display receiver assembly continuously for 11 seconds or more. 3 seconds or more elapse after the ignition switch is turned to ACC. Turn the ignition switch to ACC and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0233 Lost Communication with Blind Spot Monitor Master Module Communication stop occurs between the television camera assembly and blind spot monitor sensor LH continuously for 11 seconds or more. 3 seconds or more elapse after the ignition switch is turned to ON. Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U1000* CAN Communication Failure (Message Registry) CAN message register malfunction is detected. 3 seconds or more elapse after the ignition switch is turned to ON. Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U1110 Lost Communication with Clearance Sonar Module Communication stop occurs between the television camera assembly and clearance warning ECU assembly continuously for 11 seconds or more. 3 seconds or more elapse after the ignition switch is turned to ON. Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.


ah.

Parking Assist ECU / GTS Display "Circumference Monitoring Camera Module" (w/ Panoramic View Monitor System)

HINT:

DTC communication uses the CAN communication system.


Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display

*: Refer to Panoramic View Monitor System

Click here(Click here)

U0073 Control Module Communication Bus Off Bus off condition is detected 10 times or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the parking assist ECU and ECM continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the parking assist ECU and steering sensor continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the parking assist ECU and brake actuator assembly (skid control ECU) continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Communication stop occurs between the parking assist ECU and main body ECU (multiplex network body ECU) continuously for 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - - DTC is stored until it is cleared using the GTS.
U0163 Lost Communication with Navigation Control Module Communication stop occurs between the parking assist ECU and the radio and display receiver assembly continuously for 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0233 Lost Communication with Blind Spot Monitor Master Module Communication stop occurs between the parking assist ECU and blind spot monitor sensor LH continuously for 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0265 Lost Communication with Image Processing Sensor A Communication stop occurs between the parking assist ECU and television camera assembly continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.
U1000* CAN Communication Failure (Message Registry) CAN message register malfunction is detected. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - - DTC is stored until it is cleared using the GTS.
U1110 Lost Communication with Clearance Sonar Module Communication stop occurs between the parking assist ECU and clearance warning ECU assembly continuously for 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.


ai.

4WD ECU Assembly / GTS Display "Four Wheel Drive" (for 4WD/AWD with Dynamic Torque Control 4WD/AWD System)

HINT:

DTC communication uses the CAN communication system.


Chassis > Four Wheel Drive > Trouble Codes
50001 118
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0073 Control Module Communication Bus OFF The response sent to the brake actuator assembly (skid control ECU) or ECM is continuously invalid for 5 seconds. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds. The 4WD warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0100 Lost Communication with ECM / PCM "A" Either of the following conditions is met:
·

Communication stop occurs between the 4WD ECU assembly and transmission control ECU continuously for 2 seconds or more.

·

Communication stop occurs between the 4WD ECU assembly and ECM continuously for 2 seconds or more.

·

Communication stop occurs between the 4WD ECU assembly and ECM continuously for approximately 4 seconds or more.


All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.

·

The vehicle speed is 60 km/h (37 mph) or more.


Drive the vehicle for 5 seconds or more at a speed of 60 km/h (37 mph) or more. The 4WD warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0123 Lost Communication With Yaw Rate Sensor Module Communication stop occurs between the 4WD ECU assembly and airbag sensor assembly continuously for 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.

·

The vehicle speed is 60 km/h (37 mph) or more.


Drive the vehicle for 2 seconds or more at a speed of 60 km/h (37 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the 4WD ECU assembly and steering sensor continuously for 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. The 4WD warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Either of the following conditions is met:
·

Communication stop occurs between the 4WD ECU assembly and brake actuator assembly (skid control ECU) continuously for 3 seconds or more.

·

Communication stop occurs between the 4WD ECU assembly and brake actuator assembly (skid control ECU) continuously for 8 seconds or more.


All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. The 4WD warning light illuminates. - DTC is stored until it is cleared using the GTS.


aj.

4WD ECU Assembly / GTS Display "Four Wheel Drive" (for 4WD/AWD with Dynamic Torque Vectoring AWD System)

HINT:

DTC communication uses the CAN communication system.


Chassis > Four Wheel Drive > Trouble Codes
50001 448
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010087 Lost Communication with ECM/PCM "A" Missing Message Either of the following conditions is met:
·

Communication stop occurs between the 4WD ECU assembly and transmission control ECU continuously for 2 seconds or more.

·

Communication stop occurs between the 4WD ECU assembly and ECM continuously for 2 seconds or more.

·

Communication stop occurs between the 4WD ECU assembly and ECM continuously for approximately 4 seconds or more.


All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.

·

The vehicle speed is 60 km/h (37 mph) or more.


Drive the vehicle for 5 seconds or more at a speed of 60 km/h (37 mph) or more. The 4WD warning light illuminates. - DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the 4WD ECU assembly and airbag sensor assembly continuously for 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.

·

The vehicle speed is 60 km/h (37 mph) or more.


Drive the vehicle for 2 seconds or more at a speed of 60 km/h (37 mph) or more. - - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the 4WD ECU assembly and steering sensor continuously for 1 second or more. All conditions are met:
·

1 second or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. The 4WD warning light illuminates. - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Either of the following conditions is met:
·

Communication stop occurs between the 4WD ECU assembly and brake actuator assembly (skid control ECU) continuously for 3 seconds or more.

·

Communication stop occurs between the 4WD ECU assembly and brake actuator assembly (skid control ECU) continuously for 8 seconds or more.


All conditions are met:
·

2 seconds or more elapse after the ignition switch is turned to ON.

·

The power source voltage of the 4WD ECU assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. The 4WD warning light illuminates. - DTC is stored until it is cleared using the GTS.


ak.

Bus Buffer ECU / GTS Display "-" (w/ Bus Buffer ECU)

HINT:

The bus buffer ECU is connected to the CAN communication system, but the bus buffer ECU does not store or output CAN communication DTCs.



al.

Position Control ECU Assembly / GTS Display "Driver Seat" (w/ Memory)

HINT:

The position control ECU assembly is connected to the CAN communication system, but the position control ECU assembly does not store or output CAN communication DTCs.



am.

Steering Sensor / GTS Display "Steering Angle Sensor"

HINT:

The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.



an.

Swing Grille Actuator Assembly / GTS Display "Grille Shutter" (w/ Grille Shutter System)

HINT:

The swing grille actuator assembly is connected to the CAN communication system, but the swing grille actuator assembly does not store or output CAN communication DTCs.



ao.

Television Camera Assembly / GTS Display "-" (w/ Panoramic View Monitor System)

HINT:

The television camera assembly is connected to the CAN communication system, but the television camera assembly does not store or output CAN communication DTCs.



ap.

Airbag Sensor Assembly / GTS Display "SRS Airbag" (w/o Occupant Classification System)

HINT:

The airbag sensor assembly is connected to the CAN communication system, but the airbag sensor assembly does not store or output CAN communication DTCs.



aq.

Central Gateway ECU (Network Gateway ECU) / GTS Display "Central Gateway"

HINT:

The central gateway ECU (network gateway ECU) is connected to the CAN communication system, but the central gateway ECU (network gateway ECU) does not store or output CAN communication DTCs.




CAN BUS WAVEFORMS


C353604E02
1.521,0.677 1.854,0.281 1.854,0.281 1.99,0.281 false 4.427,1 4.427,0.271 4.427,0.271 4.563,0.271 true 4.438,3.948 4.438,2.521 4.438,2.521 5.219,2.521 true 6.354,3.948 6.354,2.521 6.354,2.521 5.646,2.521 true 5.375,3.688 5.375,4.781 5.375,4.781 5.51,4.781 false 2.063,0.208 3.208,0.448 1.146,0.24 10 false CAN Main Bus 4.656,0.198 7.052,0.479 2.396,0.281 10 false Open in CAN Main Bus Line (CANH) 5.313,3.167 6.385,3.365 1.073,0.198 10 false ECU 3.417,3.167 4.49,3.365 1.073,0.198 10 false ECU 1.594,3.167 2.667,3.365 1.073,0.198 10 false ECU 3.885,4.01 5.208,4.531 1.323,0.521 10 false Open in CAN Branch Line (CANL) 5.76,4 7.073,4.49 1.313,0.49 10 false Open in CAN Branch Line (CANH) 5.604,4.708 6.708,5.177 1.104,0.469 10 false CAN Branch 1.469,4.781 3.802,5.031 2.333,0.25 10 false : CAN Main Bus Line (CANH) 1.479,5.219 3.677,5.521 2.198,0.302 10 false : CAN Main Bus Line (CANL) 1.479,5.813 3.51,6.094 2.031,0.281 10 false : CAN Branch Line (CANH) 1.469,6.25 3.625,6.521 2.156,0.271 10 false : CAN Branch Line (CANL)

HINT:
·

This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the central gateway ECU (network gateway ECU). (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
C265973N07
0.49,0.438 0.573,0.438 0.573,0.438 0.906,0.781 true 0.458,1.594 0.552,1.594 0.552,1.594 0.917,1.156 true 0.052,0.333 0.667,0.531 0.615,0.198 10 false CANH 0.031,1.5 0.646,1.698 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.708,0.229 3.427,0.427 0.719,0.198 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Normal waveform


ii.
C265974N05
1.469,1.479 1.552,1.479 1.552,1.479 1.969,1.104 true 1.521,0.49 1.604,0.49 1.604,0.49 1.969,0.792 true 1.094,0.385 1.708,0.583 0.615,0.198 10 false CANH 1.063,1.385 1.677,1.583 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND 2.688,0.229 3.375,0.406 0.688,0.177 10 false 1 V/DIV.

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not output from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
C265975N05
1.292,0.917 0.573,0.458 0.573,0.458 0.51,0.458 true 0.469,1.417 0.552,1.417 0.552,1.417 1.063,0.958 true 0.073,0.354 0.688,0.552 0.615,0.198 10 false CANH 0.063,1.323 0.677,1.521 0.615,0.198 10 false CANL 1.344,1.917 2.875,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.229 3.344,0.438 0.625,0.208 10 false 1 V/DIV. 2.958,1.354 3.417,1.552 0.458,0.198 10 false GND

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. the actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
C265976N05
0.938,0.76 0.583,0.458 0.583,0.458 0.49,0.458 true 0.458,1.552 0.552,1.552 0.552,1.552 0.854,1.146 true 0.063,0.354 0.677,0.552 0.615,0.198 10 false CANH 0.063,1.458 0.677,1.656 0.615,0.198 10 false CANL 1.313,1.927 2.844,2.125 1.531,0.198 10 false 50 μs/DIV. 2.708,0.229 3.344,0.448 0.635,0.219 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN branch line (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. the waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




ii.
C265977N05
0.479,1.406 0.573,1.406 0.573,1.406 0.885,1.125 true 0.5,0.438 0.573,0.438 0.573,0.438 0.833,0.74 true 0.063,0.333 0.677,0.531 0.615,0.198 10 false CANH 0.052,1.302 0.667,1.5 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.417,0.458 0.719,0.229 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN branch line (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. the waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




iii.
C265978N05
0.49,0.406 0.573,0.406 0.573,0.406 0.938,0.708 true 0.469,1.458 0.552,1.458 0.552,1.458 0.938,1.156 true 0.063,0.302 0.677,0.5 0.615,0.198 10 false CANH 0.063,1.365 0.677,1.563 0.615,0.198 10 false CANL 1.323,1.927 2.854,2.125 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.281,0.469 0.583,0.24 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN main bus line (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the central gateway ECU (network gateway ECU) than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the central gateway ECU (network gateway ECU) from the open part are abnormal.

·

An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
C265979N05
0.458,1.813 0.563,1.813 0.563,1.813 1.083,1.531 true 1.063,1.333 0.573,0.906 0.573,0.906 0.49,0.906 true 0.052,0.802 0.667,1 0.615,0.198 10 false CANH 0.042,1.708 0.656,1.906 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.229 3.375,0.479 0.656,0.25 10 false 1 V/DIV. 2.99,1.354 3.385,1.563 0.396,0.208 10 false GND

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
C265980N05
0.458,1.76 0.563,1.76 0.563,1.76 0.948,1.385 true 0.458,0.5 0.552,0.5 0.552,0.5 1.021,0.708 true 0.031,0.406 0.646,0.604 0.615,0.198 10 false CANH 0.052,1.667 0.667,1.865 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.292,0.49 0.594,0.26 10 false 1 V/DIV. 2.969,1.354 3.354,1.604 0.385,0.25 10 false GND

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.






DATA SENDING/RECEIVING TABLE


a.

Data sending/receiving table

HINT:

If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.


Data Detected and Sent by Can be Checked in Data List Relevant Data List Item Relevant Data List Item
Can be Checked in Data List Cannot be Checked in Data List Selected System*3 Data List Items
Engine speed ECM
·

Combination meter assembly

·

Rack and pinion power steering gear assembly

·

4WD ECU assembly

·

Brake actuator assembly (skid control ECU)

·

Engine stop and start ECU


·

Air conditioning amplifier assembly

·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)

·

Airbag sensor assembly

·

Clearance warning ECU assembly

·

Radio and display receiver assembly

·

Telephone transceiver assembly

·

Bus buffer ECU


Engine Engine Speed
Combination Meter Engine RPM
EMPS Engine Revolution
Four Wheel Drive Engine Speed
Brake/EPB* Engine Revolutions
Stop and Start
·

Engine Speed (ECM)

·

Engine Speed


Engine coolant temperature ECM
·

Air conditioning amplifier assembly

·

Combination meter assembly

·

4WD ECU assembly

·

Swing grille actuator assembly

·

Engine stop and start ECU


·

Certification ECU (smart key ECU assembly)

·

Radio and display receiver assembly


Engine Coolant Temperature
Air Conditioner Engine Coolant Temp
Combination Meter Coolant Temperature
Four Wheel Drive Coolant Temperature
Grille Shutter Engine Coolant Temperature
Stop and Start Coolant Temperature
Shift position
·

ECM

·

Transmission control ECU


·

Certification ECU (smart key ECU assembly)

·

Brake actuator assembly (skid control ECU)

·

Blind spot monitor sensor LH

·

Clearance warning ECU assembly

·

Parking assist ECU

·

Radio and display receiver assembly

·

Engine stop and start ECU


·

Main body ECU (multiplex network body ECU)

·

Multiplex network door ECU

·

Combination meter assembly*1

·

Airbag sensor assembly

·

Television camera assembly

·

Forward recognition camera

·

Telephone transceiver assembly

·

Bus buffer ECU


Engine
·

Shift SW Status (P Range)

·

Shift SW Status (R Range)

·

Shift SW Status (N Range)

·

Shift SW Status (N,P Range)

·

Shift SW Status (S Range)

·

Shift SW Status (D Range)


Transmission
·

Shift SW Status (P Range)

·

Shift SW Status (R Range)

·

Shift SW Status (N Range)

·

Shift SW Status (N,P Range)

·

Shift SW Status (S Range)

·

Shift SW Status (D Range)


Starting Control Shift Position P or N
Power Source Control Shift P Signal
Brake/EPB* Reverse Position Switch
Blind Spot Monitor Master Reverse (Only for AT/CVT)
Clearance Sonar
·

Parking Signal

·

Reverse Signal


Clearance Warning
·

Parking Signal

·

Reverse Signal


Circumference Monitoring Camera Module Shift R Position
Navigation System Reverse Signal
Stop and Start Shift Position
Stop light switch signal ECM
·

Engine stop and start ECU

·

Transmission control ECU


·

Main body ECU (multiplex network body ECU)

·

Airbag sensor assembly

·

Radio and display receiver assembly

·

Telephone transceiver assembly


Engine Stop Light SW
Stop and Start
·

Stop Light SW (ECM)

·

Stop Light SW (ABS/VSC)


Transmission Stop Light SW
Wheel speed Brake actuator assembly (skid control ECU)
·

Rack and pinion power steering gear assembly

·

4WD ECU assembly


·

Airbag sensor assembly

·

Blind spot monitor sensor LH

·

Clearance warning ECU assembly

·

Forward recognition camera

·

Engine stop and start ECU

·

Transmission control ECU

·

ECM

·

Telephone transceiver assembly


Brake/EPB*
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


EMPS
·

Wheel Speed Right

·

Wheel Speed Left


Four Wheel Drive
·

FR Wheel Speed

·

FL Wheel Speed

·

RR Wheel Speed

·

RL Wheel Speed


Vehicle speed ECM Swing grille actuator assembly Certification ECU (smart key ECU assembly) Engine Vehicle Speed
Grille Shutter Vehicle Speed
Combination meter assembly*2 Position control ECU assembly
·

Air conditioning amplifier assembly

·

Clearance warning ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Multiplex network door ECU

·

Certification ECU (smart key ECU assembly)

·

Telephone transceiver assembly

·

Bus buffer ECU


Combination Meter Vehicle Speed Meter
Driver Seat Vehicle Speed
Brake actuator assembly (skid control ECU)
·

Combination meter assembly

·

Rack and pinion power steering gear assembly

·

Occupant detection ECU

·

Forward recognition camera

·

Radio and display receiver assembly


·

Main body ECU (multiplex network body ECU)

·

Airbag sensor assembly

·

Parking assist ECU

·

Telephone transceiver assembly


Brake/EPB* Vehicle Speed
Combination Meter Vehicle Speed Meter
EMPS Meter Vehicle Velocity
Occupant Detection VSC Vehicle Speed
Radar Cruise2 Vehicle Speed
Navigation System Vehicle Speed
Ambient temperature Air conditioning amplifier assembly
·

Combination meter assembly

·

4WD ECU assembly

·

Brake actuator assembly (skid control ECU)

·

Engine stop and start ECU

·

ECM


·

Main body ECU (multiplex network body ECU)

·

Bus buffer ECU

·

Rack and pinion power steering gear assembly

·

Clearance warning ECU assembly

·

Forward recognition camera

·

Radio and display receiver assembly

·

Telephone transceiver assembly


Air Conditioner Ambient Temp Sensor
Combination Meter
·

Ambient Temperature (Celsius)

·

Ambient Temperature (Fahrenheit)


Four Wheel Drive Ambient Temperature
Brake/EPB* Ambient Temperature
Stop and Start Ambient Temperature
Engine Ambient Temperature
Steering angle signal Steering sensor
·

Rack and pinion power steering gear assembly

·

Brake actuator assembly (skid control ECU)

·

Blind spot monitor sensor LH

·

Forward recognition camera


·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Airbag sensor assembly

·

4WD ECU assembly

·

Television camera assembly

·

Clearance warning ECU assembly

·

Parking assist ECU

·

Radio and display receiver assembly

·

Telephone transceiver assembly


EMPS Steering Angle
Brake/EPB* Steering Angle Value
Blind Spot Monitor Master Steering Angle
Radar Cruise2 Steering Angle Signal
Door courtesy Main body ECU (multiplex network body ECU) -
·

Air conditioning amplifier assembly

·

Certification ECU (smart key ECU assembly)

·

Combination meter assembly

·

Brake actuator assembly (skid control ECU)

·

Parking assist ECU

·

Radio and display receiver assembly

·

Telephone transceiver assembly

·

Bus buffer ECU


Main Body
·

FR Door Courtesy SW

·

FL Door Courtesy SW

·

RR Door Courtesy SW

·

RL Door Courtesy SW


Luggage courtesy Main body ECU (multiplex network body ECU) -
·

Bus buffer ECU

·

Certification ECU (smart key ECU assembly)

·

Combination meter assembly

·

Television camera assembly

·

Parking assist ECU

·

Radio and display receiver assembly

·

Telephone transceiver assembly


Main Body Back Door Courtesy SW
Multiplex network door ECU - Main body ECU (multiplex network body ECU) Back Door Courtesy SW

*1: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter assembly.

*2: The combination meter assembly receives a vehicle speed signal from the brake actuator assembly (skid control ECU) and sends the signal to other ECUs.

*3: According to the display on the GTS, read the Data List.

-

Enter the following menus: Body Electrical / Combination Meter / Data List

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Chassis / EMPS / Data List

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Chassis / Four Wheel Drive / Data List

for Dynamic Torque Control 4WD/AWD: Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DATA LIST / ACTIVE TEST

for Dynamic Torque Vectoring AWD: Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE VECTORING AWD SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Chassis / Brake/EPB* / Data List

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/ Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Air Conditioner / Data List

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Grille Shutter / Data List

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Power Source Control / Data List

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Chassis / Circumference Monitoring Camera Module / Data List

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Navigation System / Data List

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Driver Seat / Data List

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Occupant Detection / Data List

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST

-
-

Enter the following menus: Body Electrical / Main Body / Data List

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

-

Enter the following menus: Body Electrical / Back Door / Data List

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST


EPB*: Electric Parking Brake