17168
1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 2 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.
17141
2.INSTALL EXHAUST MANIFOLD
Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.
Temporarily install the exhaust manifold, No. 1 exhaust manifold heat insulator and No. 1 upper front floor heat insulator.
At this time, do not install the parts with bolts or nuts.
Using a 12 mm deep socket wrench, temporarily install the exhaust manifold to the cylinder head sub-assembly with 7 new nuts.
Using the 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.
17118
3.INSTALL MANIFOLD STAY
Temporarily install the manifold stay to the exhaust manifold and cylinder block sub-assembly with the bolt and nut.
Tighten the bolt and nut in the order shown in the illustration.
17167
4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
| *a | Torque Wrench Fulcrum Length |
Using a 10 mm union nut wrench, install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.8 N*m (90 kgf*cm, 78 in.*lbf)
58151
5.INSTALL NO. 1 UPPER FRONT FLOOR HEAT INSULATOR
Install the No. 1 upper front floor heat insulator to the vehicle body with the 2 nuts.
25706
6.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)
| *a | Torque Wrench Fulcrum Length |
Using a 14 mm union nut wrench, install the No. 1 vacuum transmitting pipe sub-assembly to the exhaust manifold.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf).
Install the nut and connect the No. 1 vacuum transmitting pipe sub-assembly to the exhaust manifold.
Connect the vacuum transmitting hose assembly to the No. 1 tube and slide the clip to secure it.
7.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket with the bolt.
89467B
8.INSTALL AIR FUEL RATIO SENSOR (for Sensor 1)
17410
9.INSTALL FRONT EXHAUST PIPE ASSEMBLY
Install 2 new gaskets to the front exhaust pipe assembly.
Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.
Install the front exhaust pipe assembly to the exhaust manifold and tail exhaust pipe assembly with 2 new bolts and 2 new nuts.
| *a | Tie Band |
| *b | Wire Harness Clamp |
Connect the air fuel ratio sensor connector.
Attach the 2 wire harness clamps so that the tie band is positioned as shown in the illustration.
10.INSPECT FOR EXHAUST GAS LEAK
51468B
11.INSTALL ENGINE UNDER COVER HEAT INSULATOR
51420
12.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY