Home › Engine / Hybrid System › A25A-FXS (INTAKE / EXHAUST) › EXHAUST PIPE › from 2020.08
RM3620E _51 Engine / Hybrid System _076482 A25A-FXS INTAKE / EXHAUST _0372158 EXHAUST PIPE A

A25A-FXS INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17577 1.INSTALL NO. 7 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 7 exhaust pipe support bracket to the body with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


b.

Install the exhaust pipe support to the No. 7 exhaust pipe support bracket.


Hide 17576A 2.INSTALL NO. 6 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 6 exhaust pipe support bracket to the body with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


b.

Install the exhaust pipe support to the No. 6 exhaust pipe support bracket.


Hide 17573A 3.INSTALL NO. 3 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 3 exhaust pipe support bracket to the body with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


b.

Install the exhaust pipe support to the No. 3 exhaust pipe support bracket.


Hide 17572B 4.INSTALL NO. 2 EXHAUST PIPE SUPPORT BRACKET

Hide 17408 5.INSTALL TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the tail exhaust pipe baffle sub-assembly is necessary.

·

If the tail exhaust pipe baffle sub-assembly is removed, replace it with a new one.



a.
A463470C01
0.896,0.604 1.385,0.188 1.385,0.188 1.583,0.188 true 0.594,2.063 1.25,2.063 false 0.229,1.458 0.229,1.229 0.229,1.229 0.771,0.615 true 0.229,0.115 0.354,0.115 0.354,0.115 0.76,0.281 true 0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 0.396,1.99 0.708,2.146 0.313,0.156 10 false *d 0.188,1.521 0.5,1.677 0.313,0.156 10 false *b 1.677,0.115 1.99,0.271 0.313,0.156 10 false *c
*a Baffle Edge
*b Protrusion
*c Cutout
*d Wooden Block


Set a new tail exhaust pipe baffle sub-assembly to the tail exhaust pipe assembly.


b.

Insert the exhaust tailpipe baffle sub-assembly to the position where it can be pressed in by hand.


c.

Using a plastic-faced hammer and wooden block, uniformly tap the tail exhaust pipe baffle sub-assembly onto the tail exhaust pipe assembly.

NOTICE:
·

Lightly tap the top and bottom of the exhaust tailpipe baffle sub-assembly so that the exhaust tailpipe baffle sub-assembly is pressed in without a tilt.

·

Press the exhaust tailpipe baffle sub-assembly in until the protrusion on the exhaust tailpipe assembly is fit into the cutout area of the exhaust tailpipe baffle sub-assembly.

·

Check that there is no looseness in the exhaust tailpipe baffle sub-assembly.




Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.


c.

Install the front exhaust pipe assembly to the exhaust manifold with 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 89467C 7.INSTALL AIR FUEL RATIO SENSOR (for Sensor 2)

Hide 17430 8.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Connect the tail exhaust pipe assembly to the 3 exhaust pipe supports.


c.

Install the tail exhaust pipe assembly to the front exhaust pipe assembly with 2 new bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 9.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform "Inspection After Repair" after repairing an exhaust gas leak.