Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM (for A25A-FKS) › from 2020.08
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371962 STOP AND START SYSTEM(for A25A-FKS) C

STOP AND START  STOP AND START SYSTEM(for A25A-FKS)  P323A19  Backup Boost Converter "A" Circuit Current Above Threshold  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU.

The backup boost converter helps maintain battery voltage to prevent various functions from failing if power source voltage supplied from the backup boost converter drops due to the high electrical load when the engine is restarted by stop and start control.

The backup boost converter helps maintain the power source voltage if the battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self resets according to electric signal.

The backup boost converter supplies power to:
·

Toyota safety sense

·

Tire pressure warning system

·

Vehicle stability control system

·

Power steering system

·

Audio and visual system

·

Navigation system

·

Panoramic view monitor system

·

Blind spot monitor system

·

Telematics system

·

CAN communication system

·

Meter / gauge system

·

Air conditioning system



DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P323A19 Backup Boost Converter "A" Circuit Current Above Threshold The following condition continues for 1 second or more (1 trip detection logic):
·

Overcurrent is detected at the B41, B42, B43, IG41 and EMOP terminals in the engine stop and start ECU


·

Wire harness or connector

·

Forward recognition camera

·

Millimeter wave radar sensor assembly

·

Radio and display receiver assembly (w/ Display Audio System or w/ Navigation System)

·

Parking assist ECU (w/ Panoramic View Monitor System)

·

Blind spot monitor sensor LH (w/ Blind Spot Monitor System)

·

Blind spot monitor sensor RH (w/ Blind Spot Monitor System)

·

Air conditioning control assembly

·

Cooler control switch assembly

·

Oil pump with solenoid assembly

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P323A

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

e.

Start the engine and warm it up.


f.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



g.

Depress the brake pedal and stop the vehicle.


h.

Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)


i.

Release the brake pedal with the shift lever in D to start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



j.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



WIRING DIAGRAM

A436154E02
0.135,0.125 2.625,0.427 2.49,0.302 12 false w/ Entry and Start System: 1.646,4.667 4.5,4.979 2.854,0.313 10 false Instrument Panel Junction Block Assembly 5.427,8.01 7.156,8.333 1.729,0.323 10 false Engine Stop and Start ECU 0.26,1.323 0.74,1.583 0.479,0.26 10 false ALT 0.438,2.052 0.917,2.313 0.479,0.26 10 false J/B-B 2.698,1.594 3.49,1.885 0.792,0.292 10 false IG1 NO. 1 2.708,2.729 3.5,3.021 0.792,0.292 10 false IG2 NO. 2 2.875,3.885 3.667,4.177 0.792,0.292 10 false ACC 1.833,4.344 2.625,4.635 0.792,0.292 10 false AM2 3.531,1.094 4.323,1.385 0.792,0.292 10 false EPS-IG1 3.5,3.375 4.292,3.667 0.792,0.292 10 false ECU-ACC 3.354,2.229 4.146,2.521 0.792,0.292 10 false METER-IG2 0.135,8.229 0.927,8.521 0.792,0.292 10 false A 6.313,0.969 7.104,1.26 0.792,0.292 10 false IG1 6.313,2.094 7.104,2.385 0.792,0.292 10 false IG2 6.313,3.24 7.104,3.531 0.792,0.292 10 false ACC 6.302,5.156 7.094,5.448 0.792,0.292 10 false +B 5.854,0.958 6.646,1.25 0.792,0.292 10 false G62 5.385,2.083 6.177,2.375 0.792,0.292 10 false A32 5.865,5.146 6.656,5.438 0.792,0.292 10 false A34 4.375,0.958 5.167,1.25 0.792,0.292 10 false 4A 4.375,2.073 5.167,2.365 0.792,0.292 10 false 4D 4.354,3.24 5.146,3.531 0.792,0.292 10 false 4A 4.375,4.198 5.167,4.49 0.792,0.292 10 false 4D 1.167,0.948 1.958,1.24 0.792,0.292 10 false 4K 1.177,1.708 1.969,2 0.792,0.292 10 false 4L 1.156,2.438 1.948,2.729 0.792,0.292 10 false 4A 1.177,3.594 1.969,3.885 0.792,0.292 10 false 4A 1.167,4.208 1.958,4.5 0.792,0.292 10 false 4A 5.885,0.729 6.677,1.021 0.792,0.292 10 false 21*2 5.885,1.854 6.677,2.146 0.792,0.292 10 false 18*2 5.896,3.021 6.688,3.313 0.792,0.292 10 false 19*2 5.948,4.906 6.74,5.198 0.792,0.292 10 false 1 4.385,0.74 5.177,1.031 0.792,0.292 10 false 55 4.385,1.875 5.177,2.167 0.792,0.292 10 false 32 4.354,3.031 5.146,3.323 0.792,0.292 10 false 40 4.417,3.979 5.208,4.271 0.792,0.292 10 false 3 4.083,5.292 4.875,5.583 0.792,0.292 10 false EFI NO. 1 1.042,5.292 2.146,5.604 1.104,0.313 10 false EFI-MAIN NO. 1 2.656,5.813 3.76,6.125 1.104,0.313 10 false EFI-MAIN NO. 1 1.229,0.74 2.021,1.031 0.792,0.292 10 false 1 1.198,1.51 1.99,1.802 0.792,0.292 10 false 1 1.188,2.229 1.979,2.521 0.792,0.292 10 false 17 1.188,3.375 1.979,3.667 0.792,0.292 10 false 30 1.188,4 1.979,4.292 0.792,0.292 10 false 44 2.604,5.385 3.396,5.677 0.792,0.292 10 false 1 3.354,5.021 4.146,5.313 0.792,0.292 10 false 5 2.604,5.021 3.396,5.313 0.792,0.292 10 false 3 3.354,5.385 4.146,5.677 0.792,0.292 10 false 2 2.969,6.656 4.073,6.969 1.104,0.313 10 false ECM 3.448,6.208 4.552,6.521 1.104,0.313 10 false 15 2.958,6.313 4.063,6.625 1.104,0.313 10 false MREL 2.583,6.656 3.688,6.969 1.104,0.313 10 false A24 1.813,8.177 2.917,8.49 1.104,0.313 10 false G54 1.802,8.354 5.021,8.635 3.219,0.281 10 false Certification ECU (Smart Key ECU Assembly) 2.219,7.115 3.323,7.427 1.104,0.313 10 false 17 2.208,7.479 3.313,7.792 1.104,0.313 10 false 16 2.292,7.927 3.396,8.24 1.104,0.313 10 false 4 2.49,7.219 3.594,7.531 1.104,0.313 10 false IG1D 2.49,7.594 3.594,7.906 1.104,0.313 10 false ACCD 2.5,8.031 3.604,8.344 1.104,0.313 10 false +B 5.396,0.958 6.188,1.25 0.792,0.292 10 false A32 5.854,2.083 6.646,2.375 0.792,0.292 10 false G62 5.854,3.24 6.646,3.531 0.792,0.292 10 false G62 5.385,3.24 6.177,3.531 0.792,0.292 10 false A32 4.938,3.844 5.729,4.135 0.792,0.292 10 false B 5.406,0.729 6.198,1.021 0.792,0.292 10 false 21*1 5.396,1.854 6.188,2.146 0.792,0.292 10 false 18*1 5.417,3.021 6.208,3.313 0.792,0.292 10 false 19*1 4.458,7.365 5.25,7.656 0.792,0.292 10 false *2: for RHD 4.438,6.979 5.229,7.271 0.792,0.292 10 false *1: for LHD

A436155E02
0.135,0.125 2.625,0.427 2.49,0.302 12 false w/o Entry and Start System: 1.646,4.667 4.5,4.979 2.854,0.313 10 false Instrument Panel Junction Block Assembly 5.427,8.01 7.156,8.333 1.729,0.323 10 false Engine Stop and Start ECU 0.26,1.323 0.74,1.583 0.479,0.26 10 false ALT 0.438,2.052 0.917,2.313 0.479,0.26 10 false J/B-B 2.698,1.594 3.49,1.885 0.792,0.292 10 false IG1 NO. 1 2.708,2.729 3.5,3.021 0.792,0.292 10 false IG2 NO. 2 2.875,3.885 3.667,4.177 0.792,0.292 10 false ACC 1.833,4.344 2.625,4.635 0.792,0.292 10 false AM2 3.531,1.094 4.323,1.385 0.792,0.292 10 false EPS-IG1 3.469,3.375 4.26,3.667 0.792,0.292 10 false ECU-ACC 3.365,2.229 4.156,2.521 0.792,0.292 10 false METER-IG2 0.135,8.229 0.927,8.521 0.792,0.292 10 false A 6.125,0.969 6.917,1.26 0.792,0.292 10 false IG1 6.125,2.094 6.917,2.385 0.792,0.292 10 false IG2 6.125,3.24 6.917,3.531 0.792,0.292 10 false ACC 6.125,5.156 6.917,5.448 0.792,0.292 10 false +B 5.667,0.958 6.458,1.25 0.792,0.292 10 false G62 5.198,2.083 5.99,2.375 0.792,0.292 10 false A32 5.677,5.156 6.469,5.448 0.792,0.292 10 false A34 4.375,0.938 5.167,1.229 0.792,0.292 10 false 4A 4.375,2.073 5.167,2.365 0.792,0.292 10 false 4D 4.354,3.24 5.146,3.531 0.792,0.292 10 false 4A 4.375,4.198 5.167,4.49 0.792,0.292 10 false 4D 1.167,0.938 1.958,1.229 0.792,0.292 10 false 4K 1.177,1.698 1.969,1.99 0.792,0.292 10 false 4L 1.156,2.438 1.948,2.729 0.792,0.292 10 false 4A 1.177,3.583 1.969,3.875 0.792,0.292 10 false 4A 1.167,4.208 1.958,4.5 0.792,0.292 10 false 4A 5.708,0.74 6.5,1.031 0.792,0.292 10 false 21*2 5.708,1.844 6.5,2.135 0.792,0.292 10 false 18*2 5.719,3.021 6.51,3.313 0.792,0.292 10 false 19*2 5.781,4.906 6.573,5.198 0.792,0.292 10 false 1 4.385,0.74 5.177,1.031 0.792,0.292 10 false 55 4.385,1.875 5.177,2.167 0.792,0.292 10 false 32 4.354,3.031 5.146,3.323 0.792,0.292 10 false 40 4.417,3.979 5.208,4.271 0.792,0.292 10 false 3 4.083,5.292 4.875,5.583 0.792,0.292 10 false EFI NO. 1 1.042,5.292 2.146,5.604 1.104,0.313 10 false EFI-MAIN NO. 1 2.656,5.813 3.76,6.125 1.104,0.313 10 false EFI-MAIN NO. 1 1.229,0.74 2.021,1.031 0.792,0.292 10 false 1 1.198,1.51 1.99,1.802 0.792,0.292 10 false 1 1.188,2.229 1.979,2.521 0.792,0.292 10 false 17 1.188,3.375 1.979,3.667 0.792,0.292 10 false 30 1.188,4 1.979,4.292 0.792,0.292 10 false 44 2.604,5.385 3.396,5.677 0.792,0.292 10 false 1 3.354,5.021 4.146,5.313 0.792,0.292 10 false 5 2.604,5.021 3.396,5.313 0.792,0.292 10 false 3 3.354,5.385 4.146,5.677 0.792,0.292 10 false 2 2.958,6.656 4.063,6.969 1.104,0.313 10 false ECM 3.448,6.208 4.552,6.521 1.104,0.313 10 false 15 2.958,6.313 4.063,6.625 1.104,0.313 10 false MREL 2.583,6.656 3.688,6.969 1.104,0.313 10 false A24 1.813,8.177 2.917,8.49 1.104,0.313 10 false G28 1.802,8.354 5.021,8.635 3.219,0.281 10 false Ignition or Starter Switch Assembly 2.323,7.781 3.427,8.094 1.104,0.313 10 false 7 3.604,7.521 4.708,7.833 1.104,0.313 10 false 6 3.615,7.781 4.719,8.094 1.104,0.313 10 false 8 2.51,7.771 3.615,8.083 1.104,0.313 10 false AM1 3.219,7.531 4.323,7.844 1.104,0.313 10 false ACC 3.302,7.76 4.406,8.073 1.104,0.313 10 false IG1 5.177,0.958 5.969,1.25 0.792,0.292 10 false A32 5.667,2.083 6.458,2.375 0.792,0.292 10 false G62 5.688,3.24 6.479,3.531 0.792,0.292 10 false G62 5.188,3.24 5.979,3.531 0.792,0.292 10 false A32 4.865,3.729 5.656,4.021 0.792,0.292 10 false B 5.208,0.74 6,1.031 0.792,0.292 10 false 21*1 5.198,1.844 5.99,2.135 0.792,0.292 10 false 18*1 5.208,3.021 6,3.313 0.792,0.292 10 false 19*1 4.333,6.5 6.167,6.698 1.833,0.198 10 false *2: for RHD 4.313,6.083 6.146,6.281 1.833,0.198 10 false *1: for LHD

A436156E02
0.531,0.104 0.771,0.323 0.24,0.219 10 false A 0.844,5.031 1.646,5.281 0.802,0.25 10 false Battery 4.198,0.719 5,0.969 0.802,0.25 10 false BBC NO. 1 4.219,1.198 5.021,1.448 0.802,0.25 10 false BBC NO. 2 4.26,0.458 4.5,0.677 0.24,0.219 10 false 1 4.271,0.958 4.51,1.177 0.24,0.219 10 false 1 4.688,0.458 4.927,0.677 0.24,0.219 10 false 2 4.719,0.958 4.958,1.177 0.24,0.219 10 false 2 5.417,0.583 6.219,0.833 0.802,0.25 10 false A33 5.427,1.073 6.229,1.323 0.802,0.25 10 false A33 5.438,6.281 6.24,6.531 0.802,0.25 10 false A33 5.438,6.875 6.24,7.125 0.802,0.25 10 false A33 5.438,7.594 6.24,7.844 0.802,0.25 10 false A34 5.385,8.188 7.104,8.469 1.719,0.281 10 false Engine Stop and Start ECU 5.865,0.563 6.667,0.813 0.802,0.25 10 false BIN1 5.875,1.083 6.677,1.333 0.802,0.25 10 false BIN2 5.875,6.292 6.677,6.542 0.802,0.25 10 false GND1 5.854,6.885 6.656,7.135 0.802,0.25 10 false GND2 5.875,7.604 6.677,7.854 0.802,0.25 10 false DGND 5.854,4.615 6.656,4.865 0.802,0.25 10 false IG12 2.115,4.927 4.25,5.281 2.135,0.354 10 false Combination Meter Assembly 2.083,4.75 2.885,5 0.802,0.25 10 false G18 3.177,5.552 3.979,5.802 0.802,0.25 10 false IG 2.906,3.542 5.844,3.917 2.938,0.375 10 false External Backup Boost Converter 2.906,3.396 3.708,3.646 0.802,0.25 10 false A14 1.792,5.896 4.635,6.323 2.844,0.427 10 false Power Steering ECU (Rack and Pinion Power Steering Gear Assembly) 2.073,5.667 2.875,5.917 0.802,0.25 10 false C54 3.135,4.615 3.938,4.865 0.802,0.25 10 false IG+ 3.917,2.573 4.719,2.823 0.802,0.25 10 false DON2 5.448,2.354 6.25,2.604 0.802,0.25 10 false 19 3.49,5.427 4.292,5.677 0.802,0.25 10 false 4 3.469,4.49 4.271,4.74 0.802,0.25 10 false 38 5.51,0.854 6.313,1.104 0.802,0.25 10 false 1 5.51,0.365 6.313,0.615 0.802,0.25 10 false 3 5.51,6.073 6.313,6.323 0.802,0.25 10 false 8 5.5,6.656 6.302,6.906 0.802,0.25 10 false 2 5.5,7.344 6.302,7.594 0.802,0.25 10 false 6 5.448,5.323 6.25,5.573 0.802,0.25 10 false 6*2 5.396,4.385 6.198,4.635 0.802,0.25 10 false 10*2 4.49,1.479 4.729,1.698 0.24,0.219 10 false B 2.167,2.115 2.969,2.365 0.802,0.25 10 false BBC NO. 3 2.25,1.854 2.49,2.073 0.24,0.219 10 false 1 3,1.844 3.24,2.063 0.24,0.219 10 false 11 0.938,2.115 1.74,2.365 0.802,0.25 10 false R/B NO.1 5.417,2.563 6.219,2.813 0.802,0.25 10 false A34 5.885,2.583 6.688,2.833 0.802,0.25 10 false DON2 4.375,2.469 5.177,2.719 0.802,0.25 10 false 1 4,3.094 4.802,3.344 0.802,0.25 10 false GND 4.375,2.969 5.177,3.219 0.802,0.25 10 false 6 3.302,1.969 4.104,2.219 0.802,0.25 10 false BIN 2.646,1.854 2.885,2.073 0.24,0.219 10 false 2 2.479,3.219 3.281,3.469 0.802,0.25 10 false BBC NO. 4 3.094,2.969 3.333,3.188 0.24,0.219 10 false 5 3.271,3.073 4.073,3.323 0.802,0.25 10 false BO1 1.406,3.542 2.208,3.792 0.802,0.25 10 false +B2 1.49,3.083 2.292,3.333 0.802,0.25 10 false +B 0.74,3.813 1.969,4.26 1.229,0.448 10 false Stereo Component Amplifier Assembly 1.885,3.531 2.688,3.781 0.802,0.25 10 false M2 1.885,3.073 2.688,3.323 0.802,0.25 10 false M2 1.906,2.573 2.708,2.823 0.802,0.25 10 false M3 3.01,2.438 3.813,2.688 0.802,0.25 10 false 12 1.896,3.323 2.698,3.573 0.802,0.25 10 false 16 1.948,2.865 2.75,3.115 0.802,0.25 10 false 1 1.385,2.583 2.188,2.833 0.802,0.25 10 false ACC 4.938,4.604 5.74,4.854 0.802,0.25 10 false A32 5.427,4.604 6.229,4.854 0.802,0.25 10 false G62 5.427,5.542 6.229,5.792 0.802,0.25 10 false G62 4.938,5.542 5.74,5.792 0.802,0.25 10 false A32 3.292,2.563 4.094,2.813 0.802,0.25 10 false ACO 1.938,2.365 2.74,2.615 0.802,0.25 10 false 12 3.99,1.979 4.792,2.229 0.802,0.25 10 false ACC 4.354,1.854 4.594,2.073 0.24,0.219 10 false 3 4.875,4.396 5.677,4.646 0.802,0.25 10 false 10*1 4.938,5.313 5.74,5.563 0.802,0.25 10 false 6*1 5.854,5.563 6.656,5.813 0.802,0.25 10 false IG11 1.365,7.667 2.469,7.927 1.104,0.26 10 false *2: for RHD 1.354,7.302 2.458,7.563 1.104,0.26 10 false *1: for LHD 2.885,3.719 5.823,4.094 2.938,0.375 10 false (Eco Run Vehicle Converter Assembly)

A475457E01
5.76,0.698 6.375,0.896 0.615,0.198 10 false IG13 5.75,1.281 6.365,1.479 0.615,0.198 10 false B12 5.76,3.427 6.375,3.625 0.615,0.198 10 false B42 5.729,5.615 6.344,5.813 0.615,0.198 10 false IG41 5.344,7.042 7.094,7.313 1.75,0.271 10 false Engine Stop and Start ECU 0.115,1.958 2.906,2.25 2.792,0.292 10 false Telematics Transceiver Assembly 0.104,3.802 3.302,4.219 3.198,0.417 10 false Radio and Display Receiver Assembly*3 0.104,3.615 2.896,3.906 2.792,0.292 10 false G3 0.125,5.073 3.615,5.354 3.49,0.281 10 false G66 2.927,6.635 5.25,7.021 2.323,0.385 10 false Clearance Warning ECU Assembly 0.083,6.51 3.573,6.792 3.49,0.281 10 false G72 0.073,8.063 3.563,8.344 3.49,0.281 10 false Forward Recognition Camera 0.073,7.906 3.563,8.188 3.49,0.281 10 false P8 5.125,9.448 7,9.875 1.875,0.427 10 false *4 w/o Display Audio System 5.354,2.656 5.969,2.854 0.615,0.198 10 false 24*2 5.385,5.365 6,5.563 0.615,0.198 10 false 3*2 1.063,1.208 1.677,1.406 0.615,0.198 10 false +B 0.906,2.896 1.521,3.094 0.615,0.198 10 false ACC1 1.01,3.448 1.625,3.646 0.615,0.198 10 false +B1 0.125,1.76 2.917,2.052 2.792,0.292 10 false H10 1.396,3.344 2.01,3.542 0.615,0.198 10 false 4 1.344,2.771 1.958,2.969 0.615,0.198 10 false 15 1.354,1.094 1.969,1.292 0.615,0.198 10 false 1 1.01,4.698 1.625,4.896 0.615,0.198 10 false +B1 1.365,4.573 1.979,4.771 0.615,0.198 10 false 4 1.021,6.125 1.635,6.323 0.615,0.198 10 false IG1 1.375,6 1.99,6.198 0.615,0.198 10 false 11 1.031,7.521 1.646,7.719 0.615,0.198 10 false IGB 1.375,8.698 1.99,8.896 0.615,0.198 10 false 5 1.021,0.583 1.635,0.781 0.615,0.198 10 false IG2 1.354,0.51 1.969,0.708 0.615,0.198 10 false 19 0.135,5.219 3.625,5.5 3.49,0.281 10 false Radio Receiver Assembly*4 5.76,2.896 6.375,3.094 0.615,0.198 10 false AC41 5.302,0.688 5.781,0.958 0.479,0.271 10 false G62 4.823,1.271 5.302,1.542 0.479,0.271 10 false A32 4.802,2.896 5.281,3.167 0.479,0.271 10 false A32 4.813,3.448 5.292,3.719 0.479,0.271 10 false A32 5.313,1.271 5.792,1.542 0.479,0.271 10 false G62 5.302,2.917 5.781,3.188 0.479,0.271 10 false G62 5.313,3.448 5.792,3.719 0.479,0.271 10 false G62 4.813,0.698 5.292,0.969 0.479,0.271 10 false A32 5.313,0.479 5.927,0.677 0.615,0.198 10 false 26*2 5.333,1.063 5.948,1.26 0.615,0.198 10 false 16*2 4.813,5.604 5.292,5.875 0.479,0.271 10 false A32 5.302,5.604 5.781,5.875 0.479,0.271 10 false G62 5.333,3.219 5.948,3.417 0.615,0.198 10 false 12*2 0.083,6.646 1.969,7 1.885,0.354 10 false Network Gateway ECU 2.927,6.51 6.417,6.792 3.49,0.281 10 false H4 3.406,6.125 4.021,6.323 0.615,0.198 10 false IG 3.229,6 3.844,6.198 0.615,0.198 10 false 1 3.417,7.51 4.031,7.708 0.615,0.198 10 false IGB 3.229,7.406 3.844,7.604 0.615,0.198 10 false 8 3.042,9.396 6.531,9.677 3.49,0.281 10 false Blind Spot Monitor Sensor RH 0.073,9.229 3.563,9.51 3.49,0.281 10 false Q1 3.406,8.833 6.896,9.115 3.49,0.281 10 false BRB 1.354,7.406 1.969,7.604 0.615,0.198 10 false 7 3.24,8.698 3.854,8.896 0.615,0.198 10 false 5 2.281,9.51 5.771,9.792 3.49,0.281 10 false C 0.083,9.406 3.573,9.688 3.49,0.281 10 false Blind Spot Monitor Sensor LH 0.969,8.833 4.458,9.115 3.49,0.281 10 false BLB 3.052,9.219 6.542,9.5 3.49,0.281 10 false Q13 4.823,0.479 5.438,0.677 0.615,0.198 10 false 26*1 4.854,1.063 5.469,1.26 0.615,0.198 10 false 16*1 4.802,2.656 5.417,2.854 0.615,0.198 10 false 24*1 4.854,3.208 5.469,3.406 0.615,0.198 10 false 12*1 3.052,7.917 6.542,8.198 3.49,0.281 10 false Millimeter Wave Radar Sensor Assembly*1 3.042,7.75 6.531,8.031 3.49,0.281 10 false B9 5.125,9.073 6.979,9.438 1.854,0.365 10 false *3: w/ Display Audio System 5.156,8.708 7.01,9.073 1.854,0.365 10 false *2: for RHD 5.167,8.365 7.021,8.729 1.854,0.365 10 false *1: for LHD 4.896,5.354 5.51,5.552 0.615,0.198 10 false 3*1

A436158E03
5.354,0.615 5.813,0.813 0.458,0.198 10 false G62 4.875,0.615 5.333,0.813 0.458,0.198 10 false A32 5.417,1.667 5.875,1.865 0.458,0.198 10 false 2*2 5.792,0.625 6.25,0.823 0.458,0.198 10 false IL41 4.875,4.51 5.333,4.708 0.458,0.198 10 false A32 5.354,0.406 5.813,0.604 0.458,0.198 10 false 25*2 5.365,4.51 5.823,4.708 0.458,0.198 10 false G62 5.792,4.542 6.25,4.74 0.458,0.198 10 false B43 4.135,0.302 4.594,0.5 0.458,0.198 10 false C 0.563,5.979 1.021,6.177 0.458,0.198 10 false H7 0.125,1.281 2.458,1.646 2.333,0.365 10 false Air Conditioning Control Assembly 1.281,0.875 1.74,1.073 0.458,0.198 10 false IG+ 1.24,0.625 1.698,0.823 0.458,0.198 10 false ILL+ 0.563,6.146 2.896,6.51 2.333,0.365 10 false Navigation ECU 0.156,1.125 0.615,1.323 0.458,0.198 10 false G24 0.302,5 2.656,5.365 2.354,0.365 10 false Inner Rear View Mirror Assembly*3 1.729,3.354 2.188,3.552 0.458,0.198 10 false P2 0.313,4.833 0.771,5.031 0.458,0.198 10 false P1 1.625,0.5 2.073,0.729 0.448,0.229 10 false 8 2.24,3.344 2.698,3.542 0.458,0.198 10 false P3 1.615,0.781 2.063,1.01 0.448,0.229 10 false 9 1.76,3.135 2.208,3.365 0.448,0.229 10 false 4*4 2.25,3.135 2.698,3.365 0.448,0.229 10 false 1*5 1.615,4.365 2.063,4.594 0.448,0.229 10 false 6 1.292,4.51 1.75,4.708 0.458,0.198 10 false +B 1.313,3.354 1.771,3.552 0.458,0.198 10 false IG 4.333,8.167 6.521,8.406 2.188,0.24 10 false *4: w/ Forward Recognition Camera 4.333,7.833 5.917,8.146 1.583,0.313 10 false *3: Digital Inner Mirror 4.333,8.5 6.573,8.75 2.24,0.25 10 false *5: w/o Forward Recognition Camera 0.281,3.719 3.635,4.146 3.354,0.427 10 false Inner Rear View Mirror Assembly (EC Mirror)*4,*5 1.313,5.583 1.771,5.781 0.458,0.198 10 false +B 1.604,5.427 2.063,5.625 0.458,0.198 10 false 10 5.417,7.323 7.115,7.677 1.698,0.354 10 false Engine Stop and Start ECU 0.125,2.5 3.177,3.135 3.052,0.635 10 false Electrical Key and Tire Pressure Monitoring System Receiver Assembly 4.333,7.5 5.917,7.813 1.583,0.313 10 false *2: for RHD 4.333,7.167 5.917,7.479 1.583,0.313 10 false *1: for LHD 0.115,2.344 0.573,2.542 0.458,0.198 10 false M8 1.625,2.063 2.073,2.292 0.448,0.229 10 false 1 1.354,2.208 1.813,2.406 0.458,0.198 10 false IG 1.323,1.896 1.781,2.094 0.458,0.198 10 false +B 1.625,1.781 2.073,2.01 0.448,0.229 10 false 7 4.906,0.406 5.365,0.604 0.458,0.198 10 false 25*1 5.802,1.885 6.26,2.083 0.458,0.198 10 false B41 4.875,1.885 5.333,2.083 0.458,0.198 10 false A32 5.354,1.875 5.813,2.073 0.458,0.198 10 false G62 4.948,1.667 5.406,1.865 0.458,0.198 10 false 2*1 4.948,6.479 5.406,6.677 0.458,0.198 10 false 1*1 5.365,4.292 5.823,4.49 0.458,0.198 10 false 11*2 0.469,7.25 3.354,7.615 2.885,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 5.781,6.708 6.24,6.906 0.458,0.198 10 false IG31 1.26,6.719 1.719,6.917 0.458,0.198 10 false IG1 4.865,6.698 5.323,6.896 0.458,0.198 10 false A32 5.365,6.698 5.823,6.896 0.458,0.198 10 false G62 0.49,7.083 0.948,7.281 0.458,0.198 10 false A39 1.604,6.583 2.063,6.781 0.458,0.198 10 false 36 1.615,7.75 2.073,7.948 0.458,0.198 10 false 9 0.521,8.219 0.979,8.417 0.458,0.198 10 false G68 0.521,8.375 3.406,8.74 2.885,0.365 10 false Steering Sensor 1.271,7.875 1.729,8.073 0.458,0.198 10 false IG1 5.438,6.479 5.896,6.677 0.458,0.198 10 false 1*2 4.844,4.281 5.302,4.479 0.458,0.198 10 false 11*1

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

If electrical load from additional devices installed to the vehicle (aftermarket audio system, etc.) is applied to the B41, B42, B43 or IG41 terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate.

If the fuse function of the backup boost converter operates, any systems connected to the B41, B42, B43 or IG41 terminal in the engine stop and start ECU will not operate.

·

If DTCs P279612 (Electromagnetic Oil Pump Circuit Short to Battery), P279614 (Electromagnetic Oil Pump Circuit Open), P279796 (Electromagnetic Oil Pump Component Internal Failure) and P323A19 (Backup Boost Converter "A" Circuit Current Above Threshold) are output simultaneously, troubleshoot for DTC P279612, P279614 or P279796 first, as a malfunction which causes DTC P279612, P279614 or P279796 to be stored may also cause DTC P323A19 to be stored.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>DIAGNOSTIC TROUBLE CODE CHART

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>DTC CHECK / CLEAR

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>FREEZE FRAME DATA



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P323A19)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392
Result:
Result Proceed to
DTC P323A19 is output A
DTC P279612, P279614 or P279796 and P323A19 are output B


HINT:

If DTCs P323A19 and P279612, P279614 or P279796 are output simultaneously, troubleshoot for DTC P279612, P279614 or P279796 first.




A

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC NO. 1 FUSE AND BBC NO. 2 FUSE)

B

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC NO. 1 FUSE AND BBC NO. 2 FUSE)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the BBC NO. 1 fuse and BBC NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-1 (BIN2) - BBC NO. 2 fuse terminal 2 Always Below 1 Ω
A33-3 (BIN1) - BBC NO. 1 fuse terminal 2 Always Below 1 Ω
A33-1 (BIN2) or BBC NO. 2 fuse terminal 2 - Body ground and other terminals Always 10 kΩ or higher
A33-3 (BIN1) or BBC NO. 1 fuse terminal 2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the radio and display receiver assembly connector. (w/ Display Audio System)


c.

Disconnect the radio receiver assembly connector. (w/o Display Audio System)


d.

Disconnect the electrical key and tire pressure monitoring system receiver assembly connector. (w/ Tire Pressure Warning System)


e.

Disconnect the central gateway ECU (network gateway ECU) connector.


f.

Disconnect the clearance warning ECU assembly connector.


g.

Disconnect the forward recognition camera connector. (w/ Toyota Safety Sense)


h.

Disconnect the millimeter wave radar sensor assembly connector. (w/ Toyota Safety Sense)


i.

Disconnect the blind spot monitor sensor LH connector.


j.

Disconnect the blind spot monitor sensor RH connector.


k.

Disconnect the air conditioning control assembly connector.


l.

Disconnect the inner rear view mirror assembly connector. (w/ EC Mirror)


m.

Disconnect the inner rear view mirror assembly connector. (w/ Digital Inner Mirror)


n.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
A32-12 (B42) - G3-4 (+B1)*1 Always Below 1 Ω
A32-12 (B42) - G66-4 (+B1)*2 Always Below 1 Ω
A32-2 (B41) - M8-7 (+B)*3 Always Below 1 Ω
A32-3 (IG41) - M8-1 (IG)*3 Always Below 1 Ω
A32-3 (IG41) - G72-11 (IG1) Always Below 1 Ω
A32-3 (IG41) - H4-1 (IG) Always Below 1 Ω
A32-3 (IG41) - P8-7 (IGB)*4 Always Below 1 Ω
A32-3 (IG41) - B9-8 (IGB)*4 Always Below 1 Ω
A32-3 (IG41) - Q1-5 (BLB) Always Below 1 Ω
A32-3 (IG41) - Q13-5 (BRB) Always Below 1 Ω
A32-3 (IG41) - G24-9 (IG+) Always Below 1 Ω
A32-3 (IG41) - P2-4 (IG)*5 Always Below 1 Ω
A32-3 (IG41) - P3-1 (IG)*6 Always Below 1 Ω
A32-11 (B43) - P1-6 (+B)*7 Always Below 1 Ω
A32-11 (B43) - H7-10 (+B) Always Below 1 Ω
A32-12 (B42) or G3-4 (+B1)*1 - Body ground and other terminals Always 10 kΩ or higher
A32-12 (B42) or G66-4 (+B1)*2 - Body ground and other terminals Always 10 kΩ or higher
A32-2 (B41) or M8-7 (+B)*3 - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or M8-1 (IG)*3 - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or G72-11 (IG1) - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or H4-1 (IG) - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or P8-7 (IGB)*4 - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or B9-8 (IGB)*4 - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or Q1-5 (BLB) - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or Q13-5 (BRB) - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or G24-9 (IG+) - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or P2-4 (IG)*5 - Body ground and other terminals Always 10 kΩ or higher
A32-3 (IG41) or P3-1 (IG)*6 - Body ground and other terminals Always 10 kΩ or higher
A32-11 (B43) or P1-6 (+B)*7 - Body ground and other terminals Always 10 kΩ or higher
A32-11 (B43) or H7-10 (+B) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
G62-12 (B42) - G3-4 (+B1)*1 Always Below 1 Ω
G62-12 (B42) - G66-4 (+B1)*2 Always Below 1 Ω
G62-2 (B41) - M8-7 (+B)*3 Always Below 1 Ω
G62-3 (IG41) - M8-1 (IG)*3 Always Below 1 Ω
G62-3 (IG41) - G72-11 (IG1) Always Below 1 Ω
G62-3 (IG41) - H4-1 (IG) Always Below 1 Ω
G62-3 (IG41) - P8-7 (IGB)*4 Always Below 1 Ω
G62-3 (IG41) - Q1-5 (BLB) Always Below 1 Ω
G62-3 (IG41) - Q13-5 (BRB) Always Below 1 Ω
G62-3 (IG41) - G24-9 (IG+) Always Below 1 Ω
G62-3 (IG41) - P2-4 (IG)*5 Always Below 1 Ω
G62-3 (IG41) - P3-1 (IG)*6 Always Below 1 Ω
G62-11 (B43) - P1-6 (+B)*7 Always Below 1 Ω
G62-11 (B43) - H7-10 (+B) Always Below 1 Ω
G62-12 (B42) or G3-4 (+B1)*1 - Body ground and other terminals Always 10 kΩ or higher
G62-12 (B42) or G66-4 (+B1)*2 - Body ground and other terminals Always 10 kΩ or higher
G62-2 (B41) or M8-7 (+B)*3 - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or M8-1 (IG)*3 - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or G72-11 (IG1) - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or H4-1 (IG) - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or P8-7 (IGB)*4 - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or Q1-5 (BLB) - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or Q13-5 (BRB) - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or G24-9 (IG+) - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or P2-4 (IG)*5 - Body ground and other terminals Always 10 kΩ or higher
G62-3 (IG41) or P3-1 (IG)*6 - Body ground and other terminals Always 10 kΩ or higher
G62-11 (B43) or P1-6 (+B)*7 - Body ground and other terminals Always 10 kΩ or higher
G62-11 (B43) or H7-10 (+B) - Body ground and other terminals Always 10 kΩ or higher


*1: w/ Display Audio System

*2: w/o Display Audio System

*3: w/ Tire Pressure Warning System

*4: w/ Toyota Safety Sense

*5: w/ Forward Recognition Camera

*6: w/o Forward Recognition Camera

*7: w/ Digital Inner Mirror



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE STOP AND START ECU
A436411C02
3.333,0.5 3.833,0.75 0.5,0.25 5,0.5 5.5,0.75 0.5,0.25 5,0.167 5.5,0.417 0.5,0.25 3.427,2.302 3.635,1.344 true 4.333,2.292 4.479,1.458 true 5.604,2.281 5.563,1.448 true 6.156,2.292 5.729,1.427 true 4.76,2.292 4.646,1.469 true 3.219,2.333 3.833,2.531 0.615,0.198 10 false DGND 4.167,2.333 4.781,2.531 0.615,0.198 10 false B42 5.469,2.333 6.083,2.5 0.615,0.167 10 false IG41 6.083,2.333 6.698,2.531 0.615,0.198 10 false B41 3.469,0.531 3.927,0.729 0.458,0.198 10 false A34 5.125,0.219 5.583,0.417 0.458,0.198 10 false A32 5.125,0.542 5.583,0.74 0.458,0.198 10 false G62 5.604,0.531 6.219,0.729 0.615,0.198 10 false *2 5.594,0.219 6.208,0.417 0.615,0.198 10 false *1 0.104,0.083 0.719,0.281 0.615,0.198 10 false *a 4.635,2.333 5.25,2.531 0.615,0.198 10 false B43
*1 for LHD *2 for RHD
*a Component without harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32*1-2 (B41) - A34-6 (DGND)
G62*2-2 (B41) - A34-6 (DGND)
Always 10 kΩ or higher
A32*1-3 (IG41) - A34-6 (DGND)
G62*2-3 (IG41) - A34-6 (DGND)
Always 10 kΩ or higher
A32*1-11 (B43) - A34-6 (DGND)
G62*2-11 (B43) - A34-6 (DGND)
Always 10 kΩ or higher
A32*1-12 (B42) - A34-6 (DGND)
G62*2-12 (B42) - A34-6 (DGND)
Always 10 kΩ or higher



*1: for LHD

*2: for RHD


Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE CONDITION (B41, B42, B43 OR IG41 CIRCUIT)

NG

5.CHECK VEHICLE CONDITION (B41, B42, B43 OR IG41 CIRCUIT)
a.

Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the B41, B42, B43 or IG41 terminal circuit of the engine stop and start ECU.

Result:
Result Proceed to
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. A
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. B




A

TROUBLESHOOT ECUS CONNECTED TO TERMINALS B41, B42, B43 AND IG41

B

END (REMOVE ADDITIONAL DEVICE)