Home › Engine / Hybrid System › STOP AND START › ENGINE STOP AND START ECU › from 2020.08
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371970 ENGINE STOP AND START ECU A

STOP AND START  ENGINE STOP AND START ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine stop and start ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73900 4.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

Hide 58810J 5.REMOVE CONSOLE BOX ASSEMBLY (for RHD)

Hide 62312B 6.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 67914B 7.REMOVE FRONT DOOR SCUFF PLATE LH (for RHD)

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH (for RHD)

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55607 9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 10.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

Hide 89261A 11.REMOVE ENGINE STOP AND START ECU

a.

for LHD:

i.

for Automatic Transaxle:

Remove the engine stop and start solenoid filter.

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START SOLENOID FILTER>REMOVAL


ii.
A434531

Disconnect the 3 connectors from the engine stop and start ECU.


iii.

Detach the clamp and disconnect the wire harness from the engine stop and start ECU.


iv.
A434532

Remove the 2 nuts and engine stop and start ECU.



b.

for RHD:

i.
A421595

Detach the 2 clamps and disconnect the 4 connectors.


ii.
A421596

Disconnect the 5 connectors.


iii.
A434629

for Automatic Transaxle:

Disconnect the connector from the engine stop and start solenoid filter.


iv.
A434533

Disconnect the 3 connectors from the engine stop and start ECU.


v.
A434534

Remove the bolt, nut and engine stop and start ECU.


vi.

for Automatic Transaxle:

Remove the engine stop and start solenoid filter from the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START SOLENOID FILTER>REMOVAL