1.INSPECT TIRES
Inspect the tires for wear and proper inflation pressure.
| Tire Size | Drive Train | Front
kPa (kgf/cm2 or bar, psi) |
Rear
kPa (kgf/cm2 or bar, psi) |
|---|---|---|---|
| 225/65R17 102H | 2WD | 240 (2.4, 35) | 240 (2.4, 35) |
| 4WD/AWD | 250 (2.5, 36) | 250 (2.5, 36) | |
| 225/60R18 100H | 4WD/AWD | 230 (2.3, 33) | 230 (2.3, 33) |
| 235/55R19 101V | 2WD | 230 (2.3, 33) | 230 (2.3, 33) |
| 4WD/AWD | 240 (2.4, 35) | 240 (2.4, 35) |
| Tire Size | Front
kPa (kgf/cm2 or bar, psi) |
Rear
kPa (kgf/cm2 or bar, psi) |
|---|---|---|
| 225/65R17 102H | 230 (2.3, 33) | 230 (2.3, 33) |
| 225/60R18 100H | ||
| 235/55R19 101V | ||
| 225/55R19 99V |
| Tire Size | kPa (kgf/cm2 or bar, psi) |
|---|---|
| T165/80R17 104M | 420 (4.2, 60) |
| T165/80D17 104M | |
| T165/90D18 107M |
Perform initialization. (w/ Tire Pressure Warning System)Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
Tire pressure adjustment method when warm (w/ Tire Pressure Warning System):
Adjust the tire inflation pressure of the data list to the set pressure.
Perform initialization and check that initialization completes.Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
Check and record the value of the Data List item "Temperature in Tire". (Ts)
Check and record the ambient temperature during tire pressure adjustment. (Tm)
Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)
Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P
P = (Specified Pressure) + (Ts - Tm)
Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".
Check the tire pressure warning system for the relationship between the inflation pressure and tire pressure warning pressure.Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using a dial indicator, check the runout of the tires.
1.4 mm (0.055 in.)
2. ROTATE TIRES
|
Front of the Vehicle |
| *a | Vehicle Wheels and Spare Tire Wheel are Same |
| *b | Vehicle Wheels and Spare Tire Wheel are Not Same, or No Spare Tire |
3.INSPECT AND ADJUST WHEEL BALANCE
for Aluminum Wheel Type:
Inspect and adjust the off-the-car balance.
8.0 g (0.0176 lb)
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
Do not touch the sticking surface of the tape.
Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.
25 mm (0.984 in.)
Push the balance weight firmly to adhere it to the position.
Do not reuse the balance weight.
Use only TOYOTA genuine stick-on type balance weights or equivalent.
The inner side balance weights should be installed by clipping them to the rim.
If necessary, check and adjust the on-the-car balance.
for Steel Wheel Type:
Inspect and adjust the off-the-car balance.
8.0 g (0.0176 lb)
If necessary, check and adjust the on-the-car balance.
4.INSPECT FRONT AXLE HUB BEARING LOOSENESS
5.INSPECT FRONT AXLE HUB RUNOUT
6.INSPECT REAR AXLE HUB BEARING LOOSENESS
7.INSPECT REAR AXLE HUB RUNOUT