Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY STACK (for LITHIUM-ION BATTERY) › from 2020.08
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425018 HV BATTERY STACK(for LITHIUM-ION BATTERY) A

HYBRID / BATTERY CONTROL  HV BATTERY STACK(for LITHIUM-ION BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV supply stack sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of No. 1 HV supply stack sub-assembly

·

Replacement of No. 2 HV supply stack sub-assembly


1.

Battery status info update

2.

Prediagnostic battery charge

3.

Battery diagnosis


HV battery status information cannot be updated for 2WD:(Click here)
for 4WD/AWD:(Click here)
·

Replacement of battery ECU assembly

·

Replacement of HV battery junction block assembly


Current sensor offset learning DTCs are stored (Click here)
Replacement of hybrid battery terminal block Perform high voltage fuse accumulated load history reset for 2WD:(Click here)
for 4WD/AWD:(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.


·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·

The hybrid system has high-voltage circuits. Accidents, such as electric shock, or electric leaks may result if the hybrid system is not operated in a correct manner. Make sure to follow the correct procedure.

·

When disposing of an HV battery or HV supply stack sub-assembly, make sure to return them through an authorized collection agent who is capable of handling them safely.

·

Before returning an HV battery, make sure to perform a recovery inspection.

·

Before returning an HV supply stack sub-assembly, make sure to perform a recovery inspection.

·

Make a note of the output DTCs as some of them may be necessary for "Recovery Inspection" of the HV battery and HV supply stack sub-assemblies.



NOTICE:
·

When replacing the No. 1 HV supply stack sub-assembly or No. 2 HV supply stack sub-assembly, it is necessary to check, adjust and equalize the SOC of the HV battery. Otherwise, the engine may run longer than normal, resulting in a decrease in fuel efficiency.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>BASIC INSPECTION

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1. READ VALUE USING GTS

a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid/EV Battery Temperature 1 to 6.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid/EV Battery Temperature 1
Hybrid/EV Battery Temperature 2
Hybrid/EV Battery Temperature 3
Hybrid/EV Battery Temperature 4
Hybrid/EV Battery Temperature 5
Hybrid/EV Battery Temperature 6
50003 397 198,199,200,201,202,203

d.

Read the Data List.

NOTICE:

If any of the temperatures listed in "Hybrid/EV Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.



Hide G920NB 3.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

Hide G92Z0 5.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

Hide G920R 7.REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A462815

Remove the bolt, 3 nuts and No. 2 hybrid battery shield sub-assembly from the HV battery.


Hide G92E1 8.REMOVE NO. 1 HV BATTERY INTAKE DUCT LH

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A462117

Remove the clip to disconnect the No. 1 HV battery intake duct LH from the HV battery.


b.

Disengage the claw of hybrid battery thermistor (sensor portion) and remove the No. 1 HV battery intake duct LH.


Hide G9508 10.REMOVE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A462118

Disconnect the connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.
A462119

Disconnect the connector.


c.
A462120

Disengage the claw.


d.
A462121

Remove the 4 nuts and No. 1 HV supply stack sub-assembly.


Hide G9509 11.REMOVE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A462123

Remove the nut and disconnect the ground terminal.


b.
A462124

Disengage the clamp.


c.
A462125

Disengage the claw.


d.
A462126

Remove the 4 nuts and No. 2 HV supply stack sub-assembly.


Hide 12.PERFORM RECOVERY INSPECTION

a.

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION