The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
1.RELEASE PARKING BRAKE
for Manual Transaxle: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
except Manual Transaxle: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
2.DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
3.REMOVE REAR WHEEL
890C0A
4.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.
Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.
42312B
5.REMOVE REAR AXLE SHAFT NUT (for 4WD/AWD)
Using SST and a hammer, release the staked part of the rear axle shaft nut.
Loosen the staked part of the rear axle shaft nut completely, otherwise the threads of the rear drive shaft assembly may be damaged.
While applying the brakes, remove the rear axle shaft nut.
47319F
6.DISCONNECT REAR FLEXIBLE HOSE LH
for 2WD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER (for 2WD)>REMOVAL
for 4WD/AWD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER (for 4WD/AWD)>REMOVAL
7.DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH
for 2WD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER (for 2WD)>REMOVAL
for 4WD/AWD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER (for 4WD/AWD)>REMOVAL
42431
8.REMOVE REAR DISC
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
890C0A
9.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for 2WD)
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.
Be careful not to damage the rear axle hub and bearing assembly and connector cover.
89544E
10.DISCONNECT SKID CONTROL SENSOR (for 4WD/AWD)
Remove the bolt and disconnect the skid control sensor from the rear axle carrier sub-assembly.
Keep the tip of the skid control sensor and installation hole free of foreign matter.
Do not rotate or apply excessive force to the skid control sensor when removing it from the rear axle carrier sub-assembly. Rotating or applying excessive force may result in damage to the skid control sensor.
42450B
11.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 2WD)
Remove the 4 bolts, rear axle hub and bearing assembly and rear disc brake dust cover sub-assembly from the rear axle carrier sub-assembly.
42450B
12.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD/AWD)
| *a | Matchmark |
Place matchmarks on the rear drive shaft assembly and the rear axle hub and bearing assembly.
Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.
Do not damage the rear drive shaft outboard joint boot.
Do not push the rear axle hub and bearing assembly towards the outside of the vehicle any further than necessary.
If it is difficult to separate the rear drive shaft assembly rear axle hub and bearing assembly, tap the end of the rear drive shaft assembly using a brass bar and a hammer.
Remove the 4 bolts, rear axle hub and bearing assembly and rear disc brake dust cover sub-assembly from the rear axle carrier sub-assembly.