Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL › from 2020.08
RM3620E _52 Drivetrain _076176 AXLE AND DIFFERENTIAL _0373315 REAR DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during diaphragm oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FKS w/ Canister Pump Module:

(Click here)

·

for A25A-FKS w/o Canister Pump Module:

(Click here)

·

for M20A-FKS:

(Click here)



CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 41110 1.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY

Hide 52380 2.REMOVE REAR NO. 1 DIFFERENTIAL SUPPORT

Hide 52380C 3.REMOVE REAR NO. 2 DIFFERENTIAL SUPPORT

Hide 41330D 4.REMOVE TRANSMISSION COUPLING ASSEMBLY

Hide 41330E 5.REMOVE TRANSMISSION COUPLING CONICAL SPRING WASHER

Hide 41330J 6.REMOVE TRANSMISSION COUPLING SHIM

Hide 7.REMOVE DIAPHRAGM OIL SEAL

a.
C155113C06
0.458,0.271 0.802,0.625 false 2.406,1.625 2.104,0.583 2.104,0.583 2.302,0.583 false 1.365,0.729 1.542,0.885 0.177,0.156 10 *a 0.083,0.521 0.271,0.677 0.188,0.156 10 *b 0.302,0.104 0.677,0.26 0.375,0.156 10 SST 2.344,0.521 2.656,0.719 0.313,0.198 10 *1
*1 Diaphragm Oil Seal
*a Turn
*b Hold


Using SST, remove the diaphragm oil seal from the rear differential carrier sub-assembly.

SST
09308-10010  


Hide 8.INSTALL DIAPHRAGM OIL SEAL

a.
C293307C02
0.396,0.688 0.615,0.688 false 2.104,1.781 1.896,1.781 1.896,1.781 1.896,1.531 false 3.208,1.365 3.385,1.531 0.177,0.167 10 false *a 0.094,0.604 0.458,0.771 0.365,0.167 10 false SST 2.177,1.688 2.49,1.885 0.313,0.198 10 false *1
*1 Diaphragm Oil Seal
*a Distance


Using SST and a hammer, tap a new diaphragm oil seal into the rear differential carrier sub-assembly until it reaches the standard value.

SST
09710-30021  (09710-03121)
09950-60011  (09951-00570)
09950-70010  (09951-07100)

Standard distance:

6.5 to 7.5 mm (0.256 to 0.295 in.) (from the edge of the differential carrier sub-assembly)


NOTICE:
·

Tap the oil seal uniformly so that the oil seal is straight.

·

Do not tap the oil seal in too far.




Hide 41330J 9.INSTALL TRANSMISSION COUPLING SHIM

Hide 41330E 10.INSTALL TRANSMISSION COUPLING CONICAL SPRING WASHER

Hide 41330D 11.INSTALL TRANSMISSION COUPLING ASSEMBLY

Hide 52380 12.INSTALL REAR NO. 1 DIFFERENTIAL SUPPORT

Hide 52380C 13.INSTALL REAR NO. 2 DIFFERENTIAL SUPPORT

Hide 41110 14.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY