Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.08
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Front Camera Module Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Front Camera Module" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Front Camera Module" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Front Camera Module Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Forward recognition camera branch wire or connector

·

Power source circuit of forward recognition camera

·

Forward recognition camera ground circuit

·

Forward recognition camera



WIRING DIAGRAM

C393549E08
5.615,0.51 6.229,0.708 0.615,0.198 10 false CA1P 5.625,1.094 6.24,1.292 0.615,0.198 10 false CA1N 5.583,3.458 6.198,3.656 0.615,0.198 10 false GND 5.604,2.406 6.219,2.604 0.615,0.198 10 false IGB 3.333,2.823 4.625,3.156 1.292,0.333 10 false ECU-IG1 NO.3*2 5.385,2.281 6,2.479 0.615,0.198 10 false 7 5.333,3.302 5.948,3.5 0.615,0.198 10 false 10 5.344,1 5.958,1.198 0.615,0.198 10 false 11 5.375,0.396 5.99,0.594 0.615,0.198 10 false 5 1.823,0.385 2.448,0.583 0.625,0.198 10 false 6 1.76,0.979 2.375,1.177 0.615,0.198 10 false 16 5.208,3.99 5.823,4.188 0.615,0.198 10 false P8 5.177,4.146 7.01,4.49 1.833,0.344 10 false Forward Recognition Camera 0.375,1.438 2.573,1.771 2.198,0.333 10 false No. 2 CAN Junction Connector 0.385,1.219 1,1.417 0.615,0.198 10 false G102 1.594,2.948 3.271,3.271 1.677,0.323 10 false from IG1 NO.1 Relay*2 4.656,2.708 5.01,2.917 0.354,0.208 10 false *2 3.865,2.281 4.219,2.49 0.354,0.208 10 false *1 0.906,2.427 3.167,2.729 2.26,0.302 10 false from Engine Stop and Start ECU*1 0.271,3.698 3.896,3.969 3.625,0.271 10 false *1: for Manual Transaxle with Stop and Start System 0.25,4.052 3.771,4.51 3.521,0.458 10 false *2: w/o Stop and Start System, except Manual Transaxle with Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (FORWARD RECOGNITION CAMERA BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C386793C10
1.49,0.104 1.875,0.375 0.385,0.271 1.948,1.198 1.948,0.458 1.948,0.458 2.104,0.458 true 1.958,1.521 1.958,1.917 1.958,1.917 2.115,1.917 true 0.083,0.094 0.417,0.323 0.333,0.229 10 false *a 1.583,0.135 1.917,0.365 0.333,0.229 10 false P8 2.167,0.354 2.615,0.604 0.448,0.25 10 false CA1P 2.167,1.813 2.615,2.063 0.448,0.25 10 false CA1N
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-5 (CA1P) - P8-11 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (for Manual Transaxle with Stop and Start System) A
OK (w/o Stop and Start System) B
OK (except Manual Transaxle with Stop and Start System)
NG C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C386793C11
1.49,0.104 1.875,0.375 0.385,0.271 1.792,1.521 1.792,1.979 1.792,1.979 1.948,1.979 true 1.302,1.521 1.302,1.969 1.302,1.969 1.146,1.969 true 0.083,0.094 0.417,0.323 0.333,0.229 10 false *a 1.583,0.135 1.917,0.365 0.333,0.229 10 false P8 0.844,1.865 1.292,2.115 0.448,0.25 10 false IGB 1.99,1.854 2.438,2.104 0.448,0.25 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-10 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P8-7 (IGB) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (IGB terminal) B
NG (Other terminal) C



A

REPLACE FORWARD RECOGNITION CAMERA

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C386793C11
1.49,0.104 1.875,0.375 0.385,0.271 1.792,1.521 1.792,1.979 1.792,1.979 1.948,1.979 true 1.302,1.521 1.302,1.969 1.302,1.969 1.146,1.969 true 0.083,0.094 0.417,0.323 0.333,0.229 10 false *a 1.583,0.135 1.917,0.365 0.333,0.229 10 false P8 0.844,1.865 1.292,2.115 0.448,0.25 10 false IGB 1.99,1.854 2.438,2.104 0.448,0.25 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-10 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P8-7 (IGB) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR