DTC P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) |
DTC P032C Knock Sensor 3 Circuit Low |
DTC P032D Knock Sensor 3 Circuit High |
DTC P0332 Knock Sensor 2 Circuit Low Input (Bank 2) |
DTC P0333 Knock Sensor 2 Circuit High Input (Bank 2) |
DTC P033C Knock Sensor 4 Circuit Low Input |
DTC P033D Knock Sensor 4 Circuit High Input |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0327 | Output voltage of knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic) |
|
| P0328 | Output voltage of knock sensor (for Bank 1 Sensor 1) is 4.5 V or more (1 trip detection logic) |
|
| P0332 | Output voltage of knock sensor (for Bank 2 Sensor 1) is 0.5 V or less (1 trip detection logic) |
|
| P0333 | Output voltage of knock sensor (for Bank 2 Sensor 1) is 4.5 V or more (1 trip detection logic) |
|
| P032C | Output voltage of knock sensor (for Bank 1 Sensor 2) is 0.5 V or less (1 trip detection logic) |
|
| P032D | Output voltage of knock sensor (for Bank 1 Sensor 2) is 4.5 V or more (1 trip detection logic) |
|
| P033C | Output voltage of knock sensor (for Bank 2 Sensor 2) is 0.5 V or less (1 trip detection logic) |
|
| P033D | Output voltage of knock sensor (for Bank 2 Sensor 2) is 4.5 V or more (1 trip detection logic) |
|

| Tester Connection | Tool Setting | Condition | Specified Condition |
| D56-94 (KNK1) - D56-93 (EKNK) | 0.01 to 10 V/DIV. 0.01 to 10 msec./DIV. | Keep engine speed at 4000 rpm with warm engine | The correct waveform is as shown |
| D56-117 (KNK2) - D56-116 (EKN2) | 0.01 to 10 V/DIV. 0.01 to 10 msec./DIV. | Keep engine speed at 4000 rpm with warm engine | The correct waveform is as shown |
| D56-96 (KNK3) - D56-95 (EKN3) | 0.01 to 10 V/DIV. 0.01 to 10 msec./DIV. | Keep engine speed at 4000 rpm with warm engine | The correct waveform is as shown |
| D56-119 (KNK4) - D56-118 (EKN4) | 0.01 to 10 V/DIV. 0.01 to 10 msec./DIV. | Keep engine speed at 4000 rpm with warm engine | The correct waveform is as shown |
| Related DTCs | P0327: Knock sensor (for Bank 1 Sensor 1) open/short (Low voltage) P0328: Knock sensor (for Bank 1 Sensor 1) open/short (High voltage) P0332: Knock sensor (for Bank 2 Sensor 1) open/short (Low voltage) P0333: Knock sensor (for Bank 2 Sensor 1) open/short (High voltage) P032C: Knock sensor (for Bank 1 Sensor 2) open/short (Low voltage) P032D: Knock sensor (for Bank 1 Sensor 2) open/short (High voltage) P033C: Knock sensor (for Bank 2 Sensor 2) open/short (Low voltage) P033D: Knock sensor (for Bank 2 Sensor 2) open/short (High voltage) |
| Required Sensors/Components (Main) | Knock sensor (Bank 1, 2 Sensor 1, 2) |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | None |
| Battery voltage | 10.5 V or more |
| Time after engine start | 5 seconds or more |
| Knock sensor voltage | Less than 0.5 V |
| Knock sensor voltage | More than 4.5 V |

| 1.INSPECT KNOCK SENSOR |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D56-94 (KNK1) - D56-93 (EKNK) | 20°C (68°F) | 120 to 280 kΩ |
| D56-117 (KNK2) - D56-116 (EKN2) | 20°C (68°F) | 120 to 280 kΩ |
| D56-96 (KNK3) - D56-95 (EKN3) | 20°C (68°F) | 120 to 280 kΩ |
| D56-119 (KNK4) - D56-118 (EKN4) | 20°C (68°F) | 120 to 280 kΩ |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR) |
![]() |
Disconnect the ECM connector.
Disconnect the knock sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| b1-2 - D56-94 (KNK1) | Always | Below 1 Ω |
| b1-1 - D56-93 (EKNK) | Always | Below 1 Ω |
| b2-2 - D56-117 (KNK2) | Always | Below 1 Ω |
| b2-1 - D56-116 (EKN2) | Always | Below 1 Ω |
| b3-2 - D56-96 (KNK3) | Always | Below 1 Ω |
| b3-1 - D56-95 (EKN3) | Always | Below 1 Ω |
| b4-2 - D56-119 (KNK4) | Always | Below 1 Ω |
| b4-1 - D56-118 (EKN4) | Always | Below 1 Ω |
| b1-2 or D56-94 (KNK1) - Body ground | Always | 10 kΩ or higher |
| b1-1 or D56-93 (EKNK) - Body ground | Always | 10 kΩ or higher |
| b2-2 or D56-117 (KNK2) - Body ground | Always | 10 kΩ or higher |
| b2-1 or D56-116 (EKN2) - Body ground | Always | 10 kΩ or higher |
| b3-2 or D56-96 (KNK3) - Body ground | Always | 10 kΩ or higher |
| b3-1 or D56-95 (EKN3) - Body ground | Always | 10 kΩ or higher |
| b4-2 or D56-119 (KNK4) - Body ground | Always | 10 kΩ or higher |
| b4-1 or D56-118 (EKN4) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 3.INSPECT ECM |
Disconnect the knock sensor connector.
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Ignition switch ON | 4.5 to 5.5 V |
|
| ||||
| OK | ||
| ||