SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, use the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer. |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 650 to 750 rpm: Idling | - |
| Calculate Load | Calculated load by ECM/ Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load/ Min.: 0%, Max.: 25700% | Actual vehicle load | - |
| MAF | Air flow rate from Mass Air Flow (MAF) meter/ Min.: 0 g/sec., Max.: 655.35 g/sec. | 4.0 to 8.0 g/sec.: Idling | If the value approximately 0.0 g/sec.:
|
| Atmosphere Pressure | Atmospheric pressure/ Min.: 0 kPa, Max.: 255 kPa | Equivalent to atmospheric pressure (absolute pressure) | - |
| Coolant Temp | Engine coolant temperature: Min.: -40°C, Max.: 140°C | 80 to 100°C (176 to 212°F): After warming up | If the value -40°C (-40°F): sensor circuit open. If the value 140°C (284°F): sensor circuit shorted. |
| Intake Air | Intake air temperature/ Min.: -40°C, Max.: 140°C | Equivalent to ambient air temperature | If the value -40°C (-40°F): sensor circuit open. If the value 140°C (284°F): sensor circuit shorted. |
| Ambient Temperature | Ambient Temperature Min.: -40°C, Max.: 215°C | Actual ambient temperature | - |
| Engine Run Time | Engine run time/ Min.: 0 seconds, Max.: 65535 seconds | Time after engine start | Service data |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C , Max.: 120°C | Close to ambient air temperature | Service data |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C , Max.: 120°C | Close to ambient air temperature | Service data |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.5 V | 11 to 14 V: Idling | - |
| Accel Sens. No. 1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1/ Min.: 0%, Max.: 100% | 10 to 22%: accelerator pedal is released 54 to 86%: accelerator pedal is fully depressed | - |
| Accel Sens. No. 2 Volt % | Absolute APP No. 2/ Min.: 0%, Max.: 100% | 12 to 42%: accelerator pedal is released 66 to 98%: accelerator pedal is fully depressed | - |
| Accel Sensor Out No. 1 | APP sensor No. 1 voltage/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Accel Sensor Out No. 2 | APP sensor No. 2 voltage/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Accel Sensor Out No. 1 | APP sensor No. 1 voltage/ Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: accelerator pedal is released 2.6 to 4.5 V: accelerator pedal is fully depressed | - |
| Accel Sensor Out No. 2 | APP sensor No. 2 voltage/ Min.: 0 V, Max.: 4.98 V | 1.2 to 2.0 V: accelerator pedal is released 3.4 to 5.3 V: accelerator pedal is fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle/ ON or OFF | ON: Idling | - |
| Accel Fully Close #1 (AD) | Accelerator fully closed value No. 1 (AD)/ Min.: 0, Max.: 4.9 V | - | ETCS service data |
| Accel Fully Close Learn #1 | Accelerator fully closed learning value No. 1/ Min.: 0, Max.: 124.5 deg | - | ETCS service data |
| Accel Fully Close Learn #2 | Accelerator fully closed learning value No. 2/ Min.: 0, Max.: 124.5 deg | - | ETCS service data |
| Throttle Sensor Volt % | Absolute throttle position sensor/ Min.: 0%, Max.: 100% |
| Read the value with intrusive operation (Active Test). |
| Throttl Sensor #2 Volt % | Throttle sensor positioning #2/ Min.: 0%, Max.: 100% | - | Calculated value based on VTA2 |
| ST1 | Brake pedal signal/ ON or OFF | ON: Brake pedal depressed | - |
| System Guard | System guard/ ON or OFF | - | ETCS service data |
| Open Side Malfunction | Open side malfunction/ ON or OFF | - | ETCS service data |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle/ ON or OFF | ON: Idling | - |
| Throttle Require Position | Throttle requirement position/ Min.: 0 V, Max.: 4.9 V | 0.5 to 1.0 V: Idling | - |
| Throttle Sensor Position | Throttle sensor positioning/ Min.: 0%, Max.: 100% | 10 to 18%: Idling | Calculated value based on VTA1 |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Throttle Position No. 1 | Throttle position No. 1/ Min.: 0 V, Max.: 4.9 V |
| - |
| Throttle Position No. 2 | Throttle position No. 2/ Min.: 0 V, Max.: 4.9 V |
| Read the value with intrusive operation (Active Test). |
| Throttle Position Command | Throttle position command value/ Min.: 0 V, Max.: 4.9 V | 0.5 to 4.8 V | ETCS service data |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1/ Min.: 0 V, Max.: 4.9 V | 0.6 to 0.9 V | ETCS service data |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2/ Min.: 0 V, Max.: 4.9 V | 2.2 to 2.6 V | ETCS service data |
| Throttle Sens Open #1(AD) | Throttle sensor opener position No. 1 (AD)/ Min.: 0 V, Max.: 4.9 V | 0.6 to 0.9 V | ETCS service data |
| Throttle Motor | Whether or not throttle actuator control permitted/ ON or OFF | ON: Idling | Read the value with the ignition switch ON (Do not start engine). |
| Throttle Motor Current | Throttle actuator current/ Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | - |
| Throttle Motor DUTY | Throttle actuator/ Min.: 0%, Max.: 100% | 0.5 to 40%: Idling | - |
| Throttle Motor Current | Throttle actuator current/ Min.: 0 A, Max.: 19.92 A | 0 to 3.0 A: Idling | - |
| Throttle Motor Open Duty | Throttle actuator opening duty ratio/ Min.: 0%, Max.: 100% | 0 to 40%: During idling | When accelerator pedal depressed, duty ratio increased. |
| Throttle Motor Close Duty | Throttle actuator closed duty ratio/ Min.: 0%, Max.: 100% | 0 to 40%: During idling | When accelerator pedal released quickly, duty ratio increased. |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open)/ Min.: 0%, Max.: 100% | - | ETCS service data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close)/ Min.: 0%, Max.: 100% | - | ETCS service data |
| Throttle Fully Close Learn | Throttle valve fully closed (learned value) Min.: 0, Max.: 4.98 V | 0.4 to 0.8 V | - |
| ETCS Actuator Power | Whether or not electric throttle control system power inputted/ ON or OFF | ON: Idling | - |
| +BM Voltage | +BM voltage/ Min.: 0, Max.: 19.9 | 10 to 15 V: Idling | ETCS service data |
| Actuator Power Supply | Actuator power supply/ ON or OFF | ON: Idling | ETCS service data |
| Clutch Current | Clutch current/ Min.: 0 A, Max.: 2.49 A | - | - |
| Fail Safe Drive | Whether or not fail-safe function executed/ ON or OFF | ON: ETCS has failed | - |
| Fail Safe Drive (Main CPU) | Whether or not fail-safe function executed/ ON or OFF | ON: ETCS has failed | - |
| Injector (Port) | Injection period of the No. 1 cylinder/ Min.: 0 ms, Max.: 32.64 ms | 2.0 to 4.0 ms: idling | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1)/ Min.: 0 ml, Max.: 2.048 ml | 0 to 0.5 ml | Quantity of fuel injection volume for 10 times |
| Fuel Press Switching Valve | Fuel press switching valve status/ Low or High | Actual alcohol concentration | - |
| Fuel Pump/Speed Status | Fuel pump/speed status/ ON or OFF | - | Active Test support data |
| Vacuum Pump | Key-off EVAP system pump status/ ON or OFF | - | Active Test support data |
| EVAP (Purge) VSV | Purge VSV control duty/ Min.: 0%, Max.: 100% | 0 to 100%: During idling | Order signal from ECM |
| Evap Purge Flow | Purge flow/ Min.: 0%, Max.: 102.3% | 0 to 100%: Idling | - |
| Purge Density Learn Value | Learning value of purge density/ Min.: -50, Max.: 350.000 | Idling: -40 to 0% | Service data |
| Vapor Pressure Pump | Vapor pressure/ Min.: 33.853 kPa, Max.: 125.596 kPa | Approximately 100 kPa: Ignition switch ON | EVAP system pressure monitored by canister pressure sensor. |
| Vapor Pressure (Calculated) | Calculated EVAP system pressure/ Min.: -5.632 kPa, Max.: 715.264 kPa | Approximately 100 kPa: Ignition switch ON | - |
| EVAP System Vent Valve | Key-off EVAP system vent valve status/ ON or OFF | - | Active Test support data |
| EVAP Purge VSV | VSV status for EVAP control/ ON or OFF | - | Active Test support data |
| Target Air-Fuel Ratio | Air fuel ratio: Min.: 0, Max.: 1.998 | 0.8 to 1.2: During idling | - |
| AF Lambda B1 S1 | Short-term fuel trim associated with the Bank 1 Sensor 1/ Min.: 0, Max.: 1.99 |
| - |
| AF Lambda B2 S1 | Short-term fuel trim associated with the Bank 2 Sensor 1/ Min.: 0, Max.: 1.99 |
| - |
| AFS Voltage B1 S1 | Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/ Min.: 0 V, Max.: 7.99 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| AFS Voltage B2 S1 | Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/ Min.: 0 V, Max.: 7.99 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| AFS Current B1 S1 | Air fuel ratio sensor current Bank 1 Sensor 1/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor. |
| AFS Current B2 S1 | Air fuel ratio sensor current (for Bank 2 Sensor 1)/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor. |
| O2S B1 S2 | Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/ Min.: 0 V, Max.: 1.27 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| O2S B2 S2 | Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/ Min.: 0 V, Max.: 1.27 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| O2S Impedance B1S2 | Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/ Min.: 0 Ω, Max.: 21247.67 Ω | 5 to 15000 Ω | After driving approx. 10 min. in urban area |
| O2S Impedance B2S2 | Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/ Min.: 0 Ω, Max.: 21247.67 Ω | 5 to 15000 Ω | After driving approx. 10 min. in urban area |
| Short FT #1 | Short-term fuel trim of Bank 1/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #1 | Long-term fuel trim of Bank 1/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value. |
| Total FT #1 | Total fuel trim of bank 1 Average value for fuel trim system of Bank 1/ Min.: -0.5, Max.: 0.496 | -0.2 to 0.2: Idling | - |
| Short FT #2 | Short-term fuel trim of Bank 2/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #2 | Long-term fuel trim of Bank 2/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value. |
| Total FT #2 | Total fuel trim of bank 2 Average value for fuel trim system of Bank 2/ Min.: -0.5, Max.: 0.496 | -0.2 to 0.2: Idling | - |
| Fuel System Status #1 | Fuel system status (Bank 1)/ OL, CL, OL Drive, OL Fault or CL Fault | CL: Idling after warming up |
|
| Fuel System Status #2 | Fuel system status (Bank 2)/ OL, CL, OL Drive, OL Fault or CL Fault | CL: Idling after warming up |
|
| Air pump pressure (absolute) | Air pump pressure (absolute)/ Min.: 0 kPa, Max.: 320 kPa | Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open Close to atmospheric pressure: Air pump OFF, Air switching valve close | Refer to DTC P2431 (Click here) |
| Air Pump Pulsation Pressure | Air pump pulsation pressure/ Min.: 0 kPa, Max.: 639.98 kPa | - |
|
| Air Pump2 Pressure (Absolute) | Air pump pressure (absolute)/ Min.: 0 kPa, Max.: 320 kPa | Atmospheric pressure +1 kPa or more: Air pump ON, Air switching valve open Close to atmospheric pressure: Air pump OFF, Air switching valve close | Refer to DTC P2431 (Click here) |
| Air Pump2 Pulsation Pressure | Air pump pulsation pressure/ Min.: 0 kPa, Max.: 639.98 kPa | - |
|
| Secondary Air Control VSV | Secondary air injection system status ON or OFF | ON: Secondary air injection system operation | - |
| 2nd Air System Status | Secondary air system status/ ON or OFF | ON: Secondary air system operation | - |
| AI Test | AI operation prohibition/ READY or NOT RDY | READY | - |
| IGN Advance | Ignition timing advance for No. 1 cylinder/ Min.: -64 deg., Max.: 63.5 deg. | BTDC 5 to 15°: Idling | - |
| Knock Feedback Value | Feedback value of knocking/ Min.: -64° CA, Max.: 1983.9° CA | -22 to 0° CA: Driving, 70 km/h (44 mph) | Service data |
| Knock Correct Learn Value | Correction learning value of knocking/ Min.: -64° CA, Max.: 1983.9° CA | 0 to 22° CA: Driving, 70 km/h (44 mph) | Service data |
| ACIS VSV | VSV status for ACIS control/ ON or OFF | - | Active Test support data |
| VVT Control Status #1 | Variable valve timing (VVT) control status (Bank 1)/ ON or OFF | - | Active Test support data |
| VVT Control Status #2 | VVT control status (Bank 2)/ ON or OFF | - | Active Test support data |
| VVT Aim Angle #1 | VVT aim angle (Bank 1)/ Min.: 0%, Max.: 100% | 0%: Idling | VVT duty signal value during intrusive operation. |
| VVT Change Angle #1 | VVT change angle (Bank 1)/ Min.: 0° FR , Max.: 60° FR | 0 to 5° FR: Idling | Displacement angle during intrusive operation. |
| VVT OCV Duty #1 | VVT OCV operation duty (Bank 1)/ Min.: 0%, Max.: 100% | 0%: Idling | Requested duty value for intrusive operation. |
| VVT Aim Angle #2 | VVT aim angle (Bank 2)/ Min.: 0%, Max.: 100% | 0%: Idling | VVT duty signal value during intrusive operation. |
| VVT Change Angle #2 | VVT change angle (Bank 2)/ Min.: 0° FR , Max.: 60° FR | 0 to 5° FR: Idling | Displacement angle during intrusive operation. |
| VVT OCV Duty #2 | VVT OCV operation duty (Bank 2)/ Min.: 0%, Max.: 100% | 0%: Idling | Requested duty value for intrusive operation. |
| VVT Ex Hold Lrn Val #1 | VVT exhaust hold duty ratio learning value (Bank 1)/ Min.: 0%, Max.: 100% | 0 to 80%: Idling | - |
| VVT Ex Chg Angle #1 | VVT exhaust change angle (Bank 1)/ Min.: 0°FR, Max.: 60°FR | 0 to 40°FR: Idling | Displacement angle during intrusive operation. |
| VVT Ex OCV Duty #1 | VVT exhaust OCV duty (Bank 1)/ Min.: 0%, Max.: 100% | 0 to 100%: Idling | Requested duty value for intrusive operation. |
| VVT Ex Hold Lrn Val #2 | VVT exhaust hold duty ratio learning value (Bank 2)/ Min.: 0%, Max.: 100% | 0 to 80%: Idling | - |
| VVT Ex Chg Angle #2 | VVT exhaust change angle (Bank 2)/ Min.: 0°FR, Max.: 60°FR | 0 to 40°FR: Idling | Displacement angle during intrusive operation. |
| VVT Ex OCV Duty #2 | VVT exhaust OCV duty (Bank 2)/ Min.: 0%, Max.: 100% | 0 to 100%: Idling | Requested duty value for intrusive operation. |
| Catalyst Temp B1 S1 | Catalyst temperature (Bank 1, Sensor 1)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B2 S1 | Catalyst temperature (Bank 2, Sensor 1)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B1 S2 | Catalyst temperature (Bank 1, Sensor 2)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B2 S2 | Catalyst temperature (Bank 2, Sensor 2)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Starter Signal | Starter signal/ ON or OFF | ON: Cranking | - |
| Starter Control | Starter switch status/ ON or OFF | ON: Cranking | - |
| Power Steering Signal Record | Power steering switch signal/ ON or OFF | ON: Power steering operation | - |
| Starter Relay | Starter relay status/ ON or OFF | ON: Cranking | - |
| Power Steer. Sig. Record | Power steering signal (history)/ ON or OFF | ON: When steering wheel first turned after battery terminals connected | This signal status is usually ON until the cables are disconnected from the battery terminals. |
| ACC Relay | Acc relay status/ ON or OFF | ON: Cranking | - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | ON: P or N position | - |
| Stop Light Switch | Stop light switch/ ON or OFF | ON: Brake pedal is depressed | - |
| A/C Signal | A/C switch status/ ON or OFF | ON: A/C ON | - |
| Closed Throttle Position SW | Closed throttle position switch/ ON or OFF |
| - |
| Fuel Cut Condition | Fuel cut condition/ ON or OFF | ON: Fuel cut operating | - |
| Immobiliser Communication | Immobiliser communication/ ON or OFF | ON: Normal | - |
| Electrical Load Signal | Electrical load signal/ ON or OFF | ON: Headlights or defogger is turned ON | - |
| Check Mode | Check mode/ ON or OFF | ON: Check mode ON | Refer to Check Mode Procedure (Click here). |
| SPD Test Result | Check mode result for vehicle speed sensor/ Compl or Incmpl | - | - |
| AS Test Result | Check mode result for secondary air injection system/ Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor/ Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor (Bank 1)/ Compl or Incmpl | - | - |
| OXS2 Test Result | Check mode result for heated oxygen sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #2 | Check mode result for air fuel ratio sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (Bank 1)/ Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor/ Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor/ Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor/ Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor/ Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor/ Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor/ Compl or Incmpl | - | - |
| Component Monitor ENA | Comprehensive component monitor/ Unable or Enable | - | - |
| Component Monitor CMPL | Comprehensive component monitor/ Compl or Incmpl | - | - |
| Fuel System Monitor ENA | Fuel system monitor/ Unable or Enable | - | - |
| Fuel System Monitor CMPL | Fuel system monitor/ Compl or Incmpl | - | - |
| Misfire Monitor ENA | Misfire monitor/ Unable or Enable | - | - |
| Misfire Monitor CMPL | Misfire monitor/ Compl or Incmpl | - | - |
| EGR/VVT Monitor ENA | EGR/VVT monitor/ Unable or Enable | - | - |
| EGR/VVT Monitor CMPL | EGR/VVT monitor/ Compl or Incmpl | - | - |
| Heater Monitor ENA | O2S (A/FS) heater monitor/ Unable or Enable | - | - |
| Heater Monitor CMPL | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor ENA | O2S (A/FS) monitor/ Unable or Enable | - | - |
| O2S(A/FS) Monitor CMPL | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor ENA | A/C monitor/ Unable or Enable | - | - |
| A/C Monitor CMPL | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor ENA | 2nd air monitor/ Unable or Enable | - | - |
| 2nd Air Monitor CMPL | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor ENA | EVAP monitor/ Unable or Enable | - | - |
| EVAP Monitor CMPL | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Cat Monitor ENA | Heated catalyst monitor/ Unable or Enable | - | - |
| Heated Cat Monitor CMPL | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor ENA | Catalyst monitor/ Unable or Enable | - | - |
| Catalyst Monitor CMPL | Catalyst monitor/ Compl or Incmpl | - | - |
| # Codes (Include History) | #Codes/ Min.: 0, Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status/ ON or OFF | ON: MIL ON | - |
| MIL ON Run Distance | MIL ON run distance/ Min.: 0 km, Max.: 65535 km | Distance after DTC detected | - |
| Running Time from MIL ON | Running time from MIL ON/ Min.: 0 minute, Max.: 65535 minutes | Equivalent to running time after MIL was ON | - |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 minutes, Max.: 65535 minutes | Equivalent to time after DTCs were cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared/ Min.: 0 km, Max.: 65535 km | Equivalent to drive distance after DTCs were cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared/ Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTC cleared |
| OBD Requirements | OBD requirement | OBD2 | - |
| Number of Emission DTC | Emission related DTCs | - | Number of emission related DTCs |
| TC and TE1 | TC and TE1 terminal of DLC3/ ON or OFF | - | - |
| Ignition Trig. Count | Ignition counter/ Min.: 0, Max.: 800 | 0 to 800 | - |
| Cylinder #1 Misfire Count to Cylinder #8 Misfire Count | Misfire ratio of the cylinder 1 to 8/ Min.: 0, Max.: 255 | 0% | This item displayed only when idling engine. |
| All Cylinders Misfire Count | All cylinders misfire rate/ Min.: 0, Max.: 255 | 0 to 35 | - |
| Multi Cylinders Misfire Count | Multiple cylinder misfire rate/ Min.: 0 Max.: 65535 | 0 to 65535 | - |
| Misfire RPM | Engine speed for first misfire range/ Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: Misfire 0 | - |
| Misfire Load | Engine load for first misfire range/ Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| Misfire Margin | Misfire monitoring/ Min.: -100%, Max.: 99.21% | -100 to 99.2% | Misfire detecting margin |
| Catalyst OT MF F/C | Catalyst over temperature misfire prevention F/C/ Not Avl or Avail | Avail: Cat OT MF F/C available Not Avl: Cat OT MF F/C not available | - |
| Cat OT MF F/C History | Catalyst over temperature misfire prevention F/C history/ ON or OFF | ON: Fuel cut operation history exists | - |
| Cat OT MF F/C Cylinder #1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #5 | Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #6 | Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #7 | Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #8 | Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Power Steering Pressure | Power steering oil pressure/ Min.: -1.897 MPa, Max.: 12.799 MPa | - | - |
| ACT VSV | A/C cut status for Active Test/ ON or OFF | - | Active Test support data |
| Idle Fuel Cut | Fuel cut idle/ ON or OFF | ON: Fuel cut operation | Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm. |
| FC TAU | Fuel cut TAU: Fuel cut during very light load/ ON or OFF | ON: Fuel cut operation | The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete. |
| Alcohol Density Estimate | Alcohol Density Estimate Min.: 0%, Max.: 100% | Changes according to concentration of alcohol in fuel | - |
| Alcohol Density Learning | Status of the alcohol density learning Compl or Incmpl | Compl: Alcohol concentration learning has been completed | - |
| Model Code | Model code | - | Identifying the model code: USK6## |
| Engine Type | Engine type | - | Identifying the engine type: 3URFBE |
| Cylinder Number | Number of cylinders/ Min.: 0, Max.: 255 | - | Identifying number of cylinders: 8 |
| Transmission Type | Transmission type | - | Identifying the transmission type: ECT 6th |
| Destination | Destination | - | Identifying the destination: A (America) |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | Identifying the model year: 200# |
| System Identification | System identification | - | Identifying the engine system: Gasoline (gasoline engine) |
| Engine Speed of Cyl #1 | Engine speed for cylinder 1/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #2 | Engine speed for cylinder 2/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #3 | Engine speed for cylinder 3/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #4 | Engine speed for cylinder 4/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #5 | Engine speed for cylinder 5/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #6 | Engine speed for cylinder 6/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #7 | Engine speed for cylinder 7/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #8 | Engine speed for cylinder 8/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Av Engine Speed of All Cyl | Engine speed for all cylinders/ Min.: 0 rpm, Max.: 25600 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| SPD (NT) | Input shaft speed/ Min.: 0 rpm, Max.: 12750 rpm | Lock-up is
| Data is displayed in increments of 50 rpm |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | Lower by -12.5% or increase 25% |
|
| Activate the VSV for Secondary Air Control | Activate the Secondary Air System | ON/OFF |
|
| Activate the VSV for Intake Control | Activate VSV for intake control | ON/OFF | - |
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | - |
| Control the A/C Cut Signal | Control A/C cut signal | ON/OFF | - |
| Control the Fuel Pump / Speed | Activate fuel pump | ON/OFF | Engine is stopped. |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Prohibit the Catalyst OT Misfire prevent F/C | Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire | ON: Fuel cut is prohibited | Confirm that the Vehicle is Stopped and Engine Speed is 3000 rpm or less. |
| Activate the Starter Relay | Activate the starter relay | ON/OFF | Engine is stopped. |
| Activate the ACC Cut Relay | Activate the ACC CUT relay | ON/OFF | Engine is stopped. |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open Open: throttle valve opens slowly | This test is possible when the following conditions are met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open Open: throttle valve opens fast | Same as above. |
| Control the VVT Linear (Bank 1) | Control Variable Valve Timing (VVT) [Bank 1] | -128 to 127% This value added to present OCV control duty |
|
| Control the VVT System (Bank 1) | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| Control the VVT Linear (Bank 2) | Control Variable Valve Timing (VVT) [Bank 2] | -128 to 127% This value added to present OCV control duty |
|
| Control the VVT System (Bank 2) | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| Control the VVT Exhaust Linear (Bank 1) | Control VVT (Bank 1) | -128 to 127% This value added to present OCV control duty |
|
| Control the VVT Exhaust Linear (Bank 2) | Control VVT (Bank 2) | -128 to 127% This value added to present OCV control duty |
|
| Activate the Vacuum Pump | Activate vacuum pump (built into canister pump module) | ON/OFF | - |
| Activate the VSV for Vent Valve | Activate vent valve (built into canister pump module) | ON/OFF | - |
| Activate the Fuel Pressure Switching Valve | Activate fuel pressure switching valve | Low/High | Vehicle is stopped. |
| Control the Cylinder #1 Fuel Cut | Cylinder #1 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #2 Fuel Cut | Cylinder #2 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #3 Fuel Cut | Cylinder #3 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #4 Fuel Cut | Cylinder #4 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #5 Fuel Cut | Cylinder #5 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #6 Fuel Cut | Cylinder #6 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #7 Fuel Cut | Cylinder #7 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #8 Fuel Cut | Cylinder #8 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the All Cylinders Fuel Cut | All cylinder fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Check the Cylinder Compression*2 | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stop in all cylinders. |
| SYSTEM CHECK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Perform the System Check by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Evaporative System Check (Automatic Mode) | Perform 5 steps in order to operate EVAP key-off monitor automatically | 35°C (95°F) or less |
|
| Evaporative System Check (Manual Mode) | Perform 5 steps in order to operate EVAP key-off monitor manually | 35°C (95°F) or less |
|
| Air Injection Check (Automatic Mode) | Perform secondary air injection system operation automatically | With warm engine, ignition switch turned off once |
|
| Air Injection Check (Manual Mode) | Perform 7 operations in order to operate air injection system monitor manually | With warm engine, ignition switch turned off once |
|