Home › Drivetrain · A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0756    Shift Solenoid "B" Performance (Shift Solenoid Valve S2)

for Preparation Click here


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC Code
DTC Detection Condition
Trouble Area
P0756
Gear required by ECM does not match actual gear when driving. (2 trip detection logic)
  1. Shift solenoid valve S2 remains open or closed
  2. Shift solenoid valve SLT remains open or closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

This DTC indicates a stuck ON malfunction or stuck OFF malfunction of the shift solenoid valve S2.
The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0756:
Shift solenoid valve S2/OFF malfunction
Shift solenoid valve S2/ON malfunction
Required sensors/Components
Shift solenoid valve S2, Vehicle speed sensor, Throttle position sensor, Speed sensor (NT), Speed sensor (SP2)
Frequency of operation
Continuous
Duration
OFF malfunction (A), (B) and (C):
0.4 seconds
OFF malfunction (D):
Immediately
ON malfunction (A) and (B):
0.4 seconds
ON malfunction (C):
3 seconds
ON malfunction (D):
0.5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
None
Turbine speed sensor circuit
Not circuit malfunction
Output speed sensor circuit
Not circuit malfunction
Shift solenoid valve S1 circuit
Not circuit malfunction
Shift solenoid valve S2 circuit
Not circuit malfunction
Shift solenoid valve SR circuit
Not circuit malfunction
Shift solenoid valve SL1 circuit
Not circuit malfunction
Shift solenoid valve SL2 circuit
Not circuit malfunction
ECT (Engine Coolant Temperature) sensor circuit
Not circuit malfunction
KCS sensor circuit
Not circuit malfunction
ETCS (Electric Throttle Control System)
Not system down
Transmission position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT
40°C (104°F) or more
Spark advance from max. retard timing by KCS control
0° crankshaft angle or more
Engine
Starting

Transfer Position is 4WD HIGH* 
Vehicle speed sensor circuit
Not circuit malfunction
Output shaft speed sensor circuit
Not circuit malfunction
Transfer output speed
143 rpm or more
NO/NOtf (Transfer input speed/Transfer output speed)
0.9 or more, and less than 1.1

HINT:
*: This condition only applies to 4WD.


OFF Malfunction (A) 
ECM selected gear
1st
Vehicle speed
2 km/h (1.2 mph) or more, and less than 40 km/h (24.9 mph)
Throttle valve opening angle
8% or more (when actual gear is 4th)
2% or more at 1000 rpm (Conditions vary with engine speed)

OFF Malfunction (B) 
ECM selected gear
2nd
Vehicle speed
2 km/h (1.2 mph) or more
Output speed
2nd → 1st down shift point or more
Throttle valve opening angle
2% or more at 1000 rpm
(Conditions vary with engine speed)

OFF Malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Continuous time for ECM selecting 4th gear
2 seconds or more
Actual gear when ECM selected 4th gear
4th

OFF Malfunction (D) 
Current ECM selected gear
5th
Last ECM selected gear
4th

ON Malfunction (A) 
ECM selected gear
1st
Vehicle speed
2 km/h (1.2 mph) or more, and less than 40 km/h (24.9 mph)
Throttle valve opening angle
8% or more (when actual gear is 4th)
2% or more at 1000 rpm (Conditions vary with engine speed)

ON Malfunction (B) 
ECM selected gear
4th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
2% or more at 1000 rpm
(Conditions vary with engine speed)

ON Malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Vehicle speed
(During transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

ON Malfunction (D) 
ECM selected gear
5th
Engine speed - Turbine speed (NE - NT)
(After transition from 4th to 5th gear)
150 rpm or less
Vehicle speed
(After transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
  1. All of the following are met: OFF malfunction (A), (B), (C) and (D)
    2 detections are necessary per driving cycle:
    1st detection: Temporary flag ON
    2nd detection: Pending fault code ON

OFF Malfunction (A) and (B) 
Turbine speed/Output speed (NT/NO)
3.30 or more, and 7.50 or less
(This means actual gear is 1st)

OFF Malfunction (C) 
Turbine speed/Output speed (NT/NO)
0.65 or more, and 0.79 or less
(This means actual gear is 5th)

OFF Malfunction (D) 
Output record of ECU from 4th to 5th up-shifting
Recorded
[ON malfunction]
  1. Both of the following conditions are met:
    ON malfunction (A) or (B), and ON malfunction (C) or (D)

ON Malfunction (A) 
Turbine speed/Output speed (NT/NO)
1.91 or more, and 2.35 or less
(This means actual gear is 2nd)

ON Malfunction (B) 
Turbine speed/Output speed (NT/NO)
1.28 or more, and 1.53 or less
(This means actual gear is 3rd)

ON Malfunction (C) 
Turbine speed - Output speed x 4th gear ratio
(NT - NO x 4th gear ratio)
1000 rpm or more

ON Malfunction (D) 
Turbine speed - Output speed x 5th gear ratio
(NT - NO x 5th gear ratio)
1000 rpm or more

INSPECTION PROCEDURE


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the Techstream.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valve and set each shift position by yourself
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (30 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
    2. The 4th to 5th up-shift must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shift must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the Data List display on the Techstream.
    6. The shift solenoid valve S2 turns ON/OFF normally when the shift lever is in D.

      ECM gear shift command
      1st
      2nd
      3rd
      4th
      5th
      Shift solenoid valve S2
      OFF
      ON
      ON
      OFF
      OFF

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0756)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0756 is output
    A
    P0756 and other DTCs are output
    B

    HINT:
    If any other codes besides P0756 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.



    C177720E01
  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

  1. Measure the line pressure.

    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


3.INSPECT SHIFT SOLENOID VALVE S2


    A110987E09
  1. Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body
    20°C (68°F)
    11 to 15 Ω

  1. Connect the battery positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE S2
OK


4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)