Home › Drivetrain ยท A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



2. DRAIN TRANSFER OIL


    C159809
  1. Remove the 4 bolts and lower transfer case protector.

  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the transfer oil.



3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



    A156211E01

  1. Tighten the radiator drain cock plug by hand.



4. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
  1. Remove the front propeller shaft assembly (Click here).



5. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft assembly (Click here).



6. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A185584
  1. Disconnect the air fuel ratio sensor connector.



    A185585
  1. Disconnect the heated oxygen sensor connector and 2 clamps.



    A185586
  1. Remove the 3 nuts and remove the front exhaust pipe assembly.

  1. Remove the gasket form the front exhaust pipe assembly.



7. REMOVE FRONT NO. 3 EXHAUST PIPE ASSEMBLY


    A185593
  1. Remove the 2 bolts and 2 nuts.

  1. Disconnect the exhaust pipe support and remove the front No. 3 exhaust pipe sub-assembly.

  1. Remove the gasket from the front No. 2 exhaust pipe assembly.



8. REMOVE HOSE HEAT PROTECTOR


    C161816
  1. Remove the bolt and hose heat protector.



9. DISCONNECT WATER BY-PASS PIPE ASSEMBLY


    C158371
  1. Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler, and separate the by-pass pipe from the automatic transmission.

    HINT:
    Use a container to catch any coolant which flows out of the water by-pass hoses.



10. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)


    C161814
  1. Disconnect the 2 transmission oil cooler hoses.

  1. Remove the 2 bolts and transmission oil cooler with transmission oil cooler spacer.



    C157012E03
  1. Remove the 3 bolts and separate the transmission oil cooler from the transmission oil cooler spacer.

  1. Remove the 2 O-rings.



11. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)


    C155914
  1. Disconnect the 2 No. 2 transmission oil cooler hoses from the transmission oil thermostat.



    C179290
  1. Disconnect the 2 transmission oil cooler hoses.

  1. Remove the 2 bolts and transmission oil cooler with transmission oil thermostat.



    C179291E01
  1. Remove the 3 bolts and separate the transmission oil cooler from the transmission oil thermostat.

  1. Remove the 2 O-rings.



12. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C155905
  1. Remove the nut and clip, and disconnect the transmission control cable.



13. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    C155910
  1. Remove the bolt and flywheel housing under cover.



    C155911
  1. Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.



14. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


    C159641
  1. Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.



15. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    C157036
  1. Remove the 4 bolts of the rear No. 1 engine mounting insulator.



    C157035
  1. Remove the 4 nuts, 4 washers, 4 bolts and No. 3 frame crossmember.



16. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


    C157037
  1. Remove the bolt and rear engine mounting heat insulator.

  1. Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.



17. DISCONNECT WIRE HARNESS AND CONNECTOR


    C155915
  1. Remove the bolt and disconnect the ground cable.



    C157274
  1. Tilt the automatic transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



    C157278E01
  1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 transmission speed sensor connectors and 3 transfer control side connectors.

    HINT:
    Detach the claw, press down the lever, and then disconnect the transmission wire connector.

  1. Disconnect the 4 connector clamps and 8 harness clamps.

  1. Remove the bolt and disconnect the harness clamp and wire harness.



18. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    C159642
  1. Remove the 10 bolts and transmission.

    NOTICE:
    Do not use excess force when prying the automatic transmission.



19. REMOVE CONNECTOR CLAMP BRACKET
  1. Remove the 2 bolts and 2 left bank oxygen sensor connector clamp brackets from the automatic transmission.



20. REMOVE TRANSMISSION CONTROL CABLE BRACKET


    C159643
  1. Remove the 2 bolts and transmission control cable bracket.



21. REMOVE TORQUE CONVERTER ASSEMBLY
  1. Remove the torque converter clutch from the automatic transmission.



22. REMOVE TRANSFER ASSEMBLY


    C160352
  1. Remove the 8 transfer adaptor rear mounting bolts.

  1. Pull the transfer straight up and remove it from the transmission.

    NOTICE:
    Take care not to damage the rear adaptor oil seal with the transfer input gear spline.



23. INSPECT TORQUE CONVERTER CLUTCH AND DRIVE PLATE
  1. Inspect the torque converter clutch and drive plate (Click here).