Home › Engine / Hybrid System · 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

DTC    P2197    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)

DTC    P2198    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.

A171616E01


DTC No.
DTC Detection Condition
Trouble Area
P2195
P2197
Conditions (a) and (b) continue for 5 seconds or more
(2 trip detection logic):
(a) A/F sensor voltage more than 3.8 V for 5 seconds
(b) Heated Oxygen (HO2) sensor voltage 0.21 V or more
  1. Open or short in A/F sensor (for sensor 1) circuit
  2. A/F sensor (for sensor 1)
  3. A/F sensor heater (for sensor 1)
  4. Integration relay
  5. A/F sensor heater and integration relay circuits
  6. Air induction system
  7. Fuel pressure
  8. Injector
  9. ECM
While fuel-cut operation performed (during vehicle deceleration), A/F sensor current 3.6 mA or more for 3 seconds (2 trip detection logic)
  1. A/F sensor
  2. ECM
P2196
P2198
Conditions (a) and (b) continue for 5 seconds or more
(2 trip detection logic):
(a) A/F sensor voltage less than 2.8 V for 5 seconds
(b) HO2 sensor voltage less than 0.59 V
  1. Open or short in A/F sensor (for sensor 1) circuit
  2. A/F sensor (for sensor 1)
  3. A/F sensor heater (for sensor 1)
  4. Integration relay
  5. A/F sensor heater and integration relay circuits
  6. Air induction system
  7. Fuel pressure
  8. Injector
  9. ECM
While fuel-cut operation performed (during vehicle deceleration), A/F sensor current less than 1.4 mA for 3 seconds (2 trip detection logic)
  1. A/F sensor
  2. ECM

HINT:
  1. DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.
  2. DTCs P2197 and P2198 indicate malfunctions related to bank 2 A/F sensor circuit.
  3. Bank 1 refers to the bank that includes No. 1 cylinder.
  4. Bank 2 refers to the bank that includes No. 2 cylinder.
  5. When either of these DTCs is output, check the A/F sensor output voltage by entering the following menus using the Techstream: Powertrain / Engine / Data List / A/F Control System / AFS Voltage B1 S1 or AFS Voltage B2 S1.
  6. Short-term fuel trim values can also be read using the Techstream.
  7. The ECM regulates the voltages at the A1A+ and A1A- or A2A+ and A2A- terminals of the ECM to a constant level. Therefore, the A/F sensor output voltage cannot be confirmed without using the Techstream.
  8. If the A/F sensor is malfunctioning, the ECM sets the DTC P2195, P2196, P2197 or P2198.


MONITOR DESCRIPTION

  1. Sensor voltage detection monitor
    Under the air-fuel ratio feedback control, if the A/F sensor output voltage indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the A/F sensor. The ECM illuminates the MIL and stores a DTC.
    Example:
    If the A/F sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds, despite the rear HO2 sensor output voltage being less than 0.59 V, the ECM sets DTC P2196 or P2198. Alternatively, if the A/F sensor output voltage is more than 3.8 V (very lean condition) for 5 seconds despite the rear HO2 sensor output voltage being 0.21 V or more, DTC P2195 or P2197 is stored.
  1. Sensor current detection monitor
    A rich air-fuel mixture causes a low A/F sensor current, and a lean air-fuel mixture causes a high A/F sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the A/F sensor current during fuel-cut and detects any abnormal current values.
    If the A/F sensor output is 3.6 mA or more for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the A/F sensor and stores DTC P2195 or P2197 (high-side stuck). If the A/F sensor output is less than 1.4 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 or P2198 (low-side stuck).

A107165E18


MONITOR STRATEGY


Related DTCs
P2195: A/F sensor signal stuck lean (bank 1)
P2196: A/F sensor signal stuck rich (bank 1)
P2197: A/F sensor signal stuck lean (bank 2)
P2198: A/F sensor signal stuck rich (bank 2)
Required Sensors/Components (Main)
A/F sensor
Required Sensors/Components (Related)
HO2 sensor
Frequency of Operation
Continuous
Duration
5 seconds: Sensor voltage detection monitor
3 seconds: Sensor current detection monitor
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Sensor)
P0110, P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0300 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500 (Vehicle Speed Sensor)
P0505 (IAC Valve)

Sensor Voltage Detection Monitor 
Time after engine start
30 seconds or more
Fuel system status
Closed-loop

Sensor Current Detection Monitor 
Battery voltage
11 V or more
Atmospheric pressure
76 kPa (570 mmHg) or more
A/F sensor status
Activated
Continuous time of fuel cut
3 to 10 seconds
ECT
75°C (167°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Sensor Voltage Detection Monitor (Lean Side Malfunction P2195 and P2197) 
Rear HO2S voltage
Rises from less than 0.21 V to 0.59 V or more
A/F sensor voltage
More than 3.8 V for 5 seconds

Sensor Voltage Detection Monitor (Rich Side Malfunction P2196 and P2198) 
Rear HO2S voltage
Falls from 0.59 V or more to less than 0.21 V
A/F sensor voltage
Less than 2.8 V for 5 seconds

Sensor Current Detection Monitor (High Side Malfunction P2195 and P2197) 
A/F sensor current
3.6 mA or more

Sensor Current Detection Monitor (Rich Side Malfunction P2196 and P2198) 
A/F sensor current
Less than 1.4 mA

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM


A164734E05


CONFIRMATION DRIVING PATTERN

CAUTION:
Strictly observe posted speed limits, traffic laws, and road conditions when performing these drive patterns.

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

A107162E70


A107163E52

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Turn the ignition switch to ON.
  3. (c) Turn the Techstream ON.
  4. (d) Clear DTCs (Click here).
  5. (e) Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher.
  6. (f) Enter the following menus: Powertrain / Engine / Data List / All Data / Idle Fuel Cut.
  7. (g) Drive the vehicle at between 60 km/h (38 mph) and 120 km/h (75 mph) for at least 10 minutes.
  8. (h) Change the transmission to 2nd gear.
  9. (i) Drive the vehicle at the proper vehicle speed to perform fuel-cut operation.

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal fully released.
    2. Engine speed is 2500 rpm or more (fuel injection returns at 1000 rpm).

  10. (j) Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds.
  11. (k) Soon after performing step (j) above, release the accelerator pedal for at least 5 seconds without depressing the brake pedal, in order to execute fuel-cut control.
  12. (l) Allow the vehicle to decelerate until the vehicle speed declines to less than 10 km/h (6 mph).
  13. (m) Repeat steps (h) through (k) above at least 3 times in one driving cycle.

    HINT:
    Completion of all O2S (A/F) Monitor is required to change the value in Data List.


INSPECTION PROCEDURE

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  3. DTC P2A00 may be set when the air-fuel ratio is stuck rich or lean.
  4. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  5. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  6. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.
  1. (a) Connect the Techstream to the DLC3.
  2. (b) Start the engine.
  3. (c) Turn the Techstream ON.
  4. (d) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. (e) On the Techstream, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.
  6. (f) Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  7. (g) Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1 S1 and O2S B1 S2 or AFS Voltage B2 S1 and O2S B2 S2) displayed on the Techstream.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  1. The sensors react in accordance with increases and decreases in the fuel injection volume.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1 S1
(A/F)
+25%
Rich
Less than 3.1
-12.5%
Lean
More than 3.4
O2S B1 S2
(HO2)
+25%
Rich
More than 0.55
-12.5%
Lean
Less than 0.4
AFS Voltage B2 S1
(A/F)
+25%
Rich
Less than 3.1
-12.5%
Lean
More than 3.4
O2S B2 S2
(HO2)
+25%
Rich
More than 0.55
-12.5%
Lean
Less than 0.4

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor (for sensor 2) output has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E05
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E05
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus using the Techstream: Powertrain / Engine / Active Test / Control the Injection Volume for A/ F Sensor / A/F Control System / AFS Voltage B1 S1 and O2S B1 S2 or AFS Voltage B2 S1 and O2S B2 S2; and then press the graph button on the Data List view.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2195, P2196, P2197 or P2198 is output
    A
    P2195, P2196, P2197 or P2198 and other DTCs are output
    B

HINT:
If any DTCs relating to the A/F sensor (DTCs for the A/F sensor heater or A/F sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (TEST VALUE OF A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Allow the vehicle to drive in accordance with the drive pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Monitor / O2 Sensor.

  1. Check that the status of O2 Sensor is Complete. If the status is still Incomplete, drive the vehicle according to the driving pattern again.

  1. Enter the following menus: Powertrain / Engine / Monitor / O2 Sensor / Details / RANGE B1 S1.

  1. Check the test value of the A/F sensor output current during fuel-cut.
    Result 
    Result
    Proceed to
    Within normal range (1.4 mA or more, and less than 3.6 mA)
    A
    Outside normal range (Less than 1.4 mA, or 3.6 mA or more)
    B



B
Go to step 12
A


3.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream ON.

  1. Warm up the A/F sensor at an engine speed of 2500 rpm for 90 seconds.

  1. On the Techstream, enter the following menus: Powertrain / Engine / Data List / A/F Control System / Snapshot / AFS Voltage B1 S1 or AFS Voltage B2 S1 and Engine Speed.

  1. Check the A/F sensor voltage 3 times, when the engine is in each of the following conditions:

    1. While idling (check for at least 30 seconds).

    2. At an engine speed of approximately 2500 rpm (without any sudden changes in engine speed).

    3. Raise the engine speed to 4000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed.

      Standard Voltage:
      Condition
      A/F Sensor Voltage Variation
      Reference
      (1) and (2)
      Remains at approximately 3.3 V
      3.1 V to 3.4 V
      (3)
      Increases to 3.8 V or more
      This occurs during engine deceleration
      (when fuel-cut performed)

HINT:

  1. For more information, see the diagrams below.


    A107161E47

  2. If the output voltage of the A/F sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have an open circuit. (This will also happen if the A/F sensor heater has an open circuit.)
  3. If the output voltage of the A/F sensor remains at either approximately 3.8 V or more, or 2.8 V or less (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have a short circuit.
  4. The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the A/F sensor output voltage.
  5. The ECM must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 16 km/h (10 mph) to allow the ECM to learn the closed throttle valve position.
  6. When the vehicle is driven:
    The output voltage of the A/F sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The A/F sensor is functioning normally.
  7. The A/F sensor is a current output element; therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the A/F sensor or ECM will show a constant voltage result.



NG
Go to step 9
OK


4.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read DTCs using the Techstream.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    P2195, P2196, P2197 or P2198 is output
    A
    No DTC is output
    B



B
END
A


6.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


7.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read DTCs using the Techstream.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P2195, P2196, P2197 or P2198 is output
    B



B
REPLACE ECM (Click here)
A

END 

9.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E06
  1. Disconnect the A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


10.INSPECT INTEGRATION RELAY (A/F)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the A/F fuse.

    1. Remove the A/F fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

    3. Reinstall the A/F fuse.

  1. Inspect the integration relay (A/F).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      When battery voltage not applied
      10 kΩ or higher
      When battery voltage applied to terminals 1A-2 and 1A-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY (A/F)
OK


11.CHECK HARNESS AND CONNECTOR (AIR-FUEL RATIO SENSOR - ECM)
A160209E14
  1. Disconnect the A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D19-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D20-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.



  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D19-1 (HA1A) - D56-22 (HA1A)
    Always
    Below 1 Ω
    D19-3 (A1A+) - D56-126 (A1A+)
    Always
    Below 1 Ω
    D19-4 (A1A-) - D56-125 (A1A-)
    Always
    Below 1 Ω
    D20-1 (HA2A) - D56-20 (HA2A)
    Always
    Below 1 Ω
    D20-3 (A2A+) - D56-103 (A2A+)
    Always
    Below 1 Ω
    D20-4 (A2A-) - D56-102 (A2A-)
    Always
    Below 1 Ω
    D19-1 (HA1A) or D56-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D19-3 (A1A+) or D56-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    D19-4 (A1A-) or D56-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    D20-1 (HA2A) or D56-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    D20-3 (A2A+) or D56-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    D20-4 (A2A-) or D56-102 (A2A-) - Body ground
    Always
    10 kΩ or higher


    A164715E03



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


13.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read DTCs using the Techstream.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P2195, P2196, P2197 or P2198 is output
    B



B
REPLACE ECM (Click here)
A

END